SsangYong Stavic / SsangYong Rodius (2005 year). Service manual — part 396
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
7
PROPELLER SHAFT
STAVIC - 2004.09
4I
Tightening torque : 81 ~ 89 Nm
Tightening torque : 70 ~ 80 Nm
Tightening torque : 80 ~ 90 Nm
(1) Rear propeller shaft (T/C)
(2) Center bearing bracket
(3) Rear propeller shaft (Axle)
Tightening torque : 70 ~ 80 Nm
Tightening torque : 81 ~ 89 Nm
(4) Front propeller shaft (Axle)
(5) Front propeller shaft (T/C)
3. Rear axle
2. Center bearing
1. Rear - T/C
5. Front - T/C
4. Front axle
Installation
1. Installation in the reverse order of removal.
2. Keep the tigtening torque.
3. Keep the guide mark when install.
4. Check and replace parts if defective.
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
8
PROPELLER SHAFT
STAVIC - 2004.09
4I
4. INSPECTION
Disassembly
1. Place an alignment mark and remove the propeller shaft.
2. Place an alignment on the spiders before removing.
3. Remove the snap ring with snap ring pliers.
4. Tap the yoke shoulder on shaft with copper hammer to
remove the roller bearing. Remove the other bearings with
same manner.
5. If it cannot be removed, hold the welding area with vise
and remove the needle bearing by using a suitable drift
and hammer.
6. Disassemble the universal joint.
The universal joint compensates the angle changes due
to vertical movement of the axle shaft.
7. Remove the intermediate bearing bracket and remove
the bearing with special tool.
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
9
PROPELLER SHAFT
STAVIC - 2004.09
4I
Inspection
1. Visual Check
Check the components for wear and crack and replace if
needed.
2. Outer diameter of spider journal
3. Clearance between spider journal and bearing
4. Run-out of propeller shaft
Set up the dial gauge on the center point of propeller
shaft and measure the run-out. If the run-out is out of the
specified range, correct it with press or replace it with
new one.
5. Starting torque of universal joint
6. Major causes of vibration
• Balance weights missing
• Excessive run-out of propeller shaft
• When using the general bolts
• Excessive wear of universal joint
• Stuck in sleeve joint
• Vibration is mainly caused by the angle changes in
front and rear universal joint. It normally occurs when
the vehicle speed is 60 ~ 100 km/h.
Specified value
Limit
17.893 mm
17.910 mm
Specified value
Limit
0.03 ~ 0.098 mm
0.25 mm
Limit
0.4 mm
Specified value
3 ~ 8 kg.cm
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
10
PROPELLER SHAFT
STAVIC - 2004.09
4I
2. Apply the grease to the inner lip of needle roller bearing
and assemble the needle roller.
3. Install the yoke bearing shaft on the shaft and insert the
spider. Place the cap on the opposite side and tap it
with plastic hammer to seat it. Adjust the clearance of
spider below 0.1 mm and install the snap ring.
Assembly
Clean the components and replace if damaged.
1. Align the alignment marks on the yoke and assemble
the spider, bearing and snap ring.
Flange yoke
Spider
Bearing
Snap ring
Yoke
Needle roller bearing
Grease
4. Apply the specified grease on the propeller shaft and
install it.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст