SsangYong Stavic / SsangYong Rodius (2005 year). Service manual — part 168
DI10-67
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSIS
DI ENG SM - 2004.9
O
DTC
Trouble
Limp
Home
Mode
Immediately
Engine
Stop
Delayed
Engine
Stop
Torque
Reduction
(max.20%)
Help
Torque
Reduction
(max.50%)
P1603
P1604
P1605
P1148
P0400
P1235
P1608
P0335
P1170
ECU Fault
ECU Fault
ECU Fault
Accelerometer (Knock
Sensor) Learning Fault
EGR Control Valve Fault
VGT Operation Fault
ECU Fault
No Crank Signals
Torque Trim Fault - High
O
O
O
O
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- Check if the MDP is successful.
- Check the accelerometer (knock
sensor) sensor and wiring harness.
- Replace the ECU if required.
- When the EGR emission is more than
specified value.
• The EGR controller circuit is open
or short to ground.
• The EGR controller is short to
battery.
- Check the EGR actuator wiring harness.
- Check the supply voltage to EGR sole-
noid valve.
- Check if the EGR valve is stuck.
- Check the resistance of EGR valve: 15.
4
Ω.
- Check the ECU wiring harness.
• Check the ECU pin #96 for open and
short.
- The boost pressure control is faulty.
- Check the air intake system.
- Check the supply voltage to sensor.
- Check the wiring harness and the ECU
wiring harness.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- Refer to P0372.
- Refer to P0372.
DI10-68
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSIS
DI ENG SM - 2004.9
DTC
Trouble
Limp
Home
Mode
Immediately
Engine
Stop
Delayed
Engine
Stop
Torque
Reduction
(max.20%)
Help
Torque
Reduction
(max.50%)
P1676
P1677
P0671
P0672
P0673
Glow Plug Communication
Fault
Glow Plug Controller Fault
#1 Glow Plug Fault - Open
#2 Glow Plug Fault - Open
#3 Glow Plug Fault - Open
- The communication between ECU and
glow plug is faulty.
- Check the communication line between
ECU and glow plug.
- Check the glow plug wiring harness.
- Check the resistance of glow plug:
below 1
Ω.
- Check the glow plug relay.
- Check the ECU wiring harness.
• Check the ECU pin #113 for short to
ground.
- Replace the ECU if required.
- The communication between ECU and
glow plug is faulty.
- Check the communication line between
ECU and glow plug.
- Check the glow plug wiring harness.
- Check the resistance of glow plug:
below 1
Ω.
- Check the glow plug relay.
- Check the ECU wiring harness.
• Check the ECU pin #113 for short to
ground.
- Replace the ECU if required.
- The glow plug circuit is open.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω.
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
- The glow plug circuit is open.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω.
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
- The glow plug circuit is open.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω.
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
DI10-69
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSIS
DI ENG SM - 2004.9
DTC
Trouble
Limp
Home
Mode
Immediately
Engine
Stop
Delayed
Engine
Stop
Torque
Reduction
(max.20%)
Help
Torque
Reduction
(max.50%)
P0674
P0675
P1671
P1672
P1673
P1674
#4 Glow Plug Fault - Open
#5 Glow Plug Fault - Open
#1 Glow Plug Fault - Short
(B+)
#2 Glow Plug Fault - Short
(B+)
#3 Glow Plug Fault - Short
(B+)
#4 Glow Plug Fault - Short
(B+)
- The glow plug circuit is open.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω.
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
- The glow plug circuit is open.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω.
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
- The glow plug circuit is short.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω.
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
- The glow plug circuit is short.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
- The glow plug circuit is short.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
- The glow plug circuit is short.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
DI10-70
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSIS
DI ENG SM - 2004.9
DTC
Trouble
Limp
Home
Mode
Immediately
Engine
Stop
Delayed
Engine
Stop
Torque
Reduction
(max.20%)
Help
Torque
Reduction
(max.50%)
P1675
P0700
P1540
P1541
P1542
P1149
P1634
P1635
#5 Glow Plug Fault - Short
(B+)
TCU Signal Fault
Air Conditioner Operating
Circuit Fault - Open
Air Conditioner Operating
Circuit Fault - Short
Air Conditioner Operating
Circuit Fault - Short to
Ground
Too High Water Level in
Fuel Filter
Immobilizer Fault (refer to
immobilizer section)
No response from Immobi-
lizer (refer to immobilizer
section)
- The glow plug circuit is short.
- Check the communication line between
ECU and each glow plug.
- Check each glow plug wiring harness.
- Check the resistance of each glow
plug: below 1
Ω
- Check each glow plug relay.
- Check the ECU wiring harness.
- Replace the ECU if required.
- The communication between ECU and
TCU is faulty.
- Check the communication line between
ECU and TCU.
- Check the ECU pin #54, 73 for open
and short.
- Replace the ECU if required.
- Check the air conditioner sensors and
wiring harnesses.
- Check the ECU wiring harness.
- Check the ECU if required.
- Check the air conditioner sensors and
wiring harnesses.
- Check the ECU wiring harness.
- Check the ECU if required.
- Check the air conditioner sensors and
wiring harnesses.
- Check the ECU wiring harness.
- Check the ECU if required.
- Drain the water from fuel filter.
- No response from immobilizer.
- Perform the immobilizer coding again.
- Check the ECU wiring harness.
• Check the ECU pin #34 for open and
short.
- Check the immobilizer unit for open and
short or check the supply voltage.
- Check the immobilizer antenna.
- Replace the ECU if required.
- No response from immobilizer.
- Perform the immobilizer coding again.
- Check the ECU wiring harness.
• Check the ECU pin #34 for open and
short.
- Check the immobilizer unit for open and
short or check the supply voltage.
- Check the immobilizer antenna.
- Replace the ECU if required.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст