SsangYong Stavic / SsangYong Rodius (2005 year). Service manual — part 66
1G-13
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE INTAKE & EXHAUST
M162 GSL ENG SM - 2005.7
7. Remove the mounting hanger and tail exhaust pipe.
8. Check the muffler and pipes for holes, damage, open
seams, or other deterioration. Which could permit
exhaust fumes to seep into the passenger compartment
or the trunk.
9. Installation should follow the removal procedure in the
reverse order.
1G-14
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE INTAKE & EXHAUST
M162 GSL ENG SM - 2005.7
FASTENER TIGHTENING SPECIFICATIONS
SPECIFICATIONS
Lb-In
-
-
-
-
-
80 ~ 97
Lb-Ft
11 ~ 21
21 ~ 35
16.6 ~ 20.3
16.6 ~ 20.3
21 ~ 35
-
Nm
15 ~ 28
28 ~ 47
22.5 ~ 27.5
22.5 ~ 27.5
28 ~ 47
9 ~ 11
Application
Exhaust manifold to front exhaust pipe nut
Front exhaust pipe to muffler nut
Intake air duct mounting bolt
Intake manifold mounting bolt
Muffler to tail exhaust pipe nut
Resonance flap mounting bolt
DI0A-1
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
GENERAL INFORMATION
DI ENG SM - 2004.9
GENERAL INFORMATION
00
SECTION DI0A
Table of Contents
CLEANNESS . . . . . . . . . ... DI0A-2
STRUCTURE . . . . . . . . . .. DI0A-7
ENGINE CONTROLS . . . . . ... DI0A-10
ECU related components . . . . DI0A-10
Engine and sensors . . . . . .. DI0A-11
Electrical components and pre heating
system . . . . . . . . . . .. DI0A-12
INTAKE SYSTEM . . . . . . . . DI0A-13
Intake air flow chart . . . . . .. DI0A-14
EXHAUST SYSTEM . . . . . . .. DI0A-15
Exhaust air flow chart . . . . ... DI0A-16
LUBRICATION SYSTEM . . . . .. DI0A-17
COOLING SYSTEM . . . . . . . DI0A-18
Coolant flow chart . . . . . . DI0A-19
FUEL SYSTEM . . . . . . . . . DI0A-20
Fuel supply system . . . . . .. DI0A-21
MAINTENANCE AND REPAIR . . .. DI0A-22
Maintenance and lubrication . ... DI0A-22
Guidelines for
service work safety . . . . . .. DI0A-23
Vehicle lifting procedures . . . DI0A-28
OWNER INSPECTIONS AND SERVICES
. . . . . . . . . . . . . . .. DI0A-30
While operating the vehicle . . . DI0A-30
At each fuel fill . . . . . . . . DI0A-30
At least twice a month . . . . .. DI0A-30
At least monthly . . . . . . ... DI0A-30
At least twice a year . . . . . . DI0A-31
Each time the oil is changed . ... DI0A-31
At least annually . . . . . . .. DI0A-31
STANDARD BOLTS SPECIFICATIONS
. . . . . . . . . . . . . . .. DI0A-32
BASIC SPECIFICATION . . . . ... DI0A-34
Vehicle specifications . . . . ... DI0A-34
Specifications . . . . . . . ... DI0A-35
Maintenance . . . . . . . . DI0A-37
VEHICLE IDENTIFICATION . . . .. DI0A-39
Vehicle identification number (VIN)
. . . . . . . . . . . . . . DI0A-39
Manufacturer’s plate . . . . . DI0A-40
Engine serial number . . . . ... DI0A-40
Transmission & transfer case number
. . . . . . . . . . . . . . DI0A-41
HOW TO USE AND MAINTAIN WORKSHOP
MANUAL . . . . . . . . . . ... DI0A-42
Consists of workshop manual . .. DI0A-42
Manual description . . . . . .. DI0A-42
DI0A-2
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
GENERAL INFORMATION
DI ENG SM - 2004.9
The fuel system for DI engine consists of transfer (low pressure) line and high pressure line. Its highest pressure
reaches over 1600 bar. Some components in injector and HP pump are machined at the micrometer 100
µm of
preciseness. The pressure regulation and injector operation are done by electric source from engine ECU.
Accordingly, if the internal valve is stucked due to foreign materials, injector remains open. Even in this case, the
HP pump still operates to supply high pressurized fuel. This increases the pressure to combustion chamber (over
250 bar) and may cause fatal damage to engine.
You can compare the thickness of injector nozzle hole and hair as shown in below figure (left side). The right side
figure shows the clearance between internal operating elements.
Cleanness of DI Engine Fuel System and Service Procedures
The core elements of fuel system has very high preciseness that is easily affected by dust or very small foreign
material. Therefore, make sure to keep the preliminary works and job procedures in next pages. If not, lots of
system problems and claims may arise.
CLEANNESS
Hair
Nozzle hole
Valve actuator lift: 0.028 mm
Diameter: 0.40 mm
Operating
clearance:
0.002 mm
Diameter:
2.0 mm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст