SsangYong: Engine Euro 4. Service manual — part 103
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
8
DIAGNOSIS
CCCS
GND
GND
12 V
GND
GND
GND
GND
GND
12 V
GND
-
1. All door knob lock relays other than the driver
side
The value appears only when the relay is con-
nected
2. Ground level when operating
3. Battery level during normal
1. All door knob unlock relays
(Cannot operate with driver side lock knob)
The value appears only when the relay is con-
nected
2. Ground level when operating
3. Battery level when not operating
1. Windshield wiper operation switch
When equipped with the rain sensor, no in-
puts are transmitted to STICS
2. Battery level when operating
3. Ground level when not operating
1. Siren operation signal
2. Ground level when operating
3. Battery level when not operating
1. Parking brake headlamp
2. Ground level when operating
3. Battery level when not operating
1. Buzzer operation
2. Ground level when operating
3. Battery level when not operating
1. Door open and driving warning
2. Ground level when operating
3. Battery level when not operating
1. Heating grid operation relay drive output
2. Ground level when operating
3. Battery level when not operating
1. Heating grid operation relay drive output
(Operates when in armed mode)
2. Ground level when operating
3. Battery level when not operating
1. Tail lamp relay drive output
(Blink once when operating the tail lamp
switch)
2. Ground level when operating
3. Battery level when not operating
-
1.Driver side foot lamp
(Operating value delays as per dimming time)
2. Pulse signal between the battery and ground
when operating.
→ Refer to operation signal STICS specifi-
cations
38
39
40
41
42
43
44
45
46
47
48
49
All door lock other
than driver side
Driver side door
unlock relay
Windshield wiper
relay
Siren operation
Parking brake
headlamp
Buzzer operation
Door open
headlamp
Heating grid relay
Hazard warning
relay
Tail lamp relay
-
Front left foot lamp
Not
operating
Not
operating
Not
operating
Not
operating
Not
operating
Not
operating
Not
operating
Not
operating
Operating
Not
operating
-
Not
operating
12 V
12 V
GND
12 V
12 V
12 V
12 V
12 V
GND
12 V
-
Operating
Operating
Operating
Operating
Operating
Operating
Operating
Operating
Not
operating
Operating
-
Operating
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
-
Output
No.
Sensor value item
Information
Help
Input/
Output
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
9
DIAGNOSIS
CCCS
BRAKE
ECU
TCU
A/BAG
TC
RK-STICS
FFH
R/SENSOR
FA
T
C
TGS-LEVER
P/TRUNK
CCCS
1. Passenger side foot lamp
(Operating value delays as per dimming time)
2. Pulse signal between the battery and ground
when operating.
→ Refer to operation signal STICS specifi-
cations
1. Rear door foot lamp
(Operating value delays as per dimming time)
2. Pulse signal between the battery and ground
when operating.
→ Refer to operation signal STICS specifi-
cations
1. Room lamp
(Operating value delays as per dimming time)
2. Pulse signal between the battery and ground
when operating.
→ Refer to operation signal STICS specifi-
cations
1. Brightness changes according to the rheostat
volume when the tail lamp is turned on
2. Pulse signal between the battery and ground
when operating. Pulse width may change by
20% ~ 100% (based on GND).
→ Refer to operation signal STICS specifi-
cations
1. Fixed rate dimming light
(Operating value changes periodically)
2. Pulse signal between the battery and ground
when operating. Pulse width maintains 50%
of the duty rate.
→ Refer to operation signal STICS specifi-
cations
-
-
-
Controls the dimming by 20 ~ 100%
1. Windshield wiper volume value: 0 ~ 10 k
Ω
→ Value between 0 ~ Vcc
For the rain sensor equipped vehicle, no in-
puts are transmitted to STICS
1. The unit time of the windshield wiper inter-
mittent intervals
For the rain sensor equipped vehicle, no in-
puts are transmitted to STICS
50
51
52
53
54
55
56
57
58
59
60
61
Front right foot
lamp
Rear foot lamp
Room lamp
Rheostat lamp
Fixed rate dimming
control
-
-
-
Current vehicle
speed
Dimming control
Windshield wiper
operating resis-
tance stages
Intermittent time
Not
operating
Not
operating
Not
operating
Not
operating
Not
operating
-
-
-
-
-
-
Operating
Operating
Operating
Operating
Operating
-
-
-
Output
Output
Output
Output
Output
-
-
-
Output
Output
Output
Output
No.
Sensor value item
Information
Help
Input/
Output
-
-
-
A km/h
A %
A kohn
A
*
10 ms
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
10
DIAGNOSIS
CCCS
DIAGNOSIS OF MAIN DICS
Code
Malfunction
Help
- The inputs have more than 30 edge hall pulses under the limiter switch off recog-
nized as the upper position condition during the power window up or down outputs
- Check the limiter switch
- Check the sensor values
• Power window anti-trap (DICS-Main: No. 50)
• Power window limiter switch (DICS-Main: No. 56)
- When the power window motor is under load, the auto-stop orders the power win-
dow to disengage auto-up function regardless ON or OFF inputs (no pulse signals)
- No inputs of hall pulse exceeding 700 milliseconds during the power window mo-
tor down outputs under the limiter switch OFF (the upper position of the window)
conditions or no inputs of pulse exceeding 100 milliseconds during the up outputs
under the limit switch ON (the lowest position of the window) conditions.
- Replace the power window motor
- Check the driver side door actuator
- Check the sensor value
• Key lock (DICS-Main: No. 32)
- Check the driver side door actuator
• Check the method of the actuator operation
- Check the sensor value
• Key unlock (DICS-Main: No. 31)
- When the outside rearview mirror has no UP or DOWN sensor values, DICS-Main
recognizes and disables the vehicle memory function. However, when the memory
input has detected, it means the sensor is open-circuited or has different mirror
has been installed.
- Check the outside rearview mirror UP or DOWN sensor wires
- Measure sensor values and check the accordance position
• Internal DOWN switch of the outside rearview mirror (DICS-Main: No. 21)
• Internal UP switch of the outside rearview mirror (DICSMain:No. 22)
• Internal DOWN motor of the outside rearview mirror (DICS-Main: No. 37)
• Internal UP motor of the outside rearview mirror (DICSMain:No. 38)
• Internal sensor of the outside rearview mirror (DICS-Main: No. 49)
• Internal operation of the outside rearview mirror (DICSMain:No. 53)
- When the outside rearview mirror has no LEFT or RIGHT sensor values, DICS-Main
recognizes and disables the vehicle memory function. However, when the memory
input has detected, it means the sensor is open-circuited or has different mirror
has been installed.
- Check the outside rearview mirror LEFT or RIGHT sensor wires.
- Measure the sensor values and check the relevant position
• Internal RIGHT switch of the outside rearview mirror (DICS-Main: No. 19)
• Internal LEFT switch of the outside rearview mirror (DICSMain: No. 20)
• Internal RIGHT motor of the outside rearview mirror (DICSMain: No. 35)
• nternal LEFT motor of the outside rearview mirror (DICSMain: No. 36)
• Internal sensor of the outside rearview mirror (DICS-Main: No. 49)
• Internal operation of the outside rearview mirror (DICSMain: No. 53)
- The window does not lower to the certain range when autostop is detected during
the driver side window auto-up operation.
- Check the power window motor wires
- Measure the sensor values and check the relevant position
• Power window anti-trap (DICS-Main: No. 50)
• Replace the power window motor
0 X 21
0 X 22
0 X 23
0 X 24
0 X 25
0 X 26
0 X 27
Power window
limiter switch open
Defective power
window motor hall
sensor
Inactive key door lock
actuator
Inactive key door
unlock actuator
Memory switch input
during no mirror UP
or DN input
Memory switch input
during no mirror LT or
RT input
Defective auto-stop
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
11
DIAGNOSIS
CCCS
BRAKE
ECU
TCU
A/BAG
TC
RK-STICS
FFH
R/SENSOR
FA
T
C
TGS-LEVER
P/TRUNK
CCCS
1. Switch the input signal to raise the rear left
window
2. Internal input
3. Input signal transmits to STICS through CAN
1. Switch the input signal to lower the passenger's
window
2. Internal input
3. Input signal transmits to DICS-Sub through
CAN
1. Switch the input signal to lower the passenger's
window automatically
2. Internal input
3. Input signal transmits to DICS-Sub through
CAN
1. Switch the input signal to raise the passenger's
window
2. Internal input
3. Input signal transmits to DICS-Sub through
CAN
1. Switch the input signal to lower the driver side
window
2. Internal input
3. DICS-Main has direct drive circuit
1. Switch the input signal to lower the driver
side window automatically
2. Internal input
3. MICOM drives based on the signal
1. Switch input signal to raise the driver side window
2. Internal input
3. DICS-Main has direct drive circuit
1. Switch input signal to raise the driver side
window automatically (operates only when
the engine is running)
2. Internal input
3. MICOM drives based on the signal
4. When the obstruction is found (detects as hall
pulse signal), the auto-stop engages the win-
dow to be lowered by 150 mm from its position
1. Input signal of the motor protection is en-
gaged by cutting the motor output when de-
tects the increasing in currency when the
motor is stopped at the lowest position of the
driver side's window
2. Internal input
1. Input signal coming from STICS
2. Outside rearview mirrors will not fold when
the signal comes on while outside rearview
mirror is folding.
1
2
3
4
5
6
7
8
9
10
Rear left P/WDW
UP S/W
Front right P/WDW
DN S/W
Front right P/WDW
AUTO DN S/W
Front right P/WDW
UP S/W
Front left P/WDW
DN S/W
Front left P/WDW
AUTO DN S/W
Front left P/WDW
UP S/W
Front left P/WDW
AUTO UP S/W
Detecting driver's
P/WDW detention
Detecting 3 km/h
of vehicle speed
Not
operating
Not
operating
Not
detected
Not
operating
Not
operating
Not
detected
Not
operating
Not
operating
Not
detected
Not
detected
Operating
Operating
Detected
Operating
Operating
Detected
Operating
Operating
Detected
Detected
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
No.
Sensor value item
Information
Help
Input/
Output
Main DICS Input/Output Monitoring Data
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст