SsangYong Rexton. Service manual — part 307
M162 ENGINE MECHANICAL 1B1-31
SSANGYONG Y200
OIL PAN
1 Gasket. . . . . . . . . . . . . Replace
2 Bolt (M6 x 22, 6 pieces)
. . . . . . . . . ... 9-11 N•m (80-97 lb-in)
3 Drain Plug . . 22.5-27.5 N•m (16.6-20.3 lb-ft)
4 Bolt (M6 x 20, 22 pieces)
. . . . . . . . . ... 9-11 N•m (80-97 lb-in)
5 Bolt (M6 x 85, 3 pieces)
. . . . . . . . . ... 9-11 N•m (80-97 lb-in)
6 Bolt (M8 x 40, 4 pieces)
. . . . . . ... 22.5-27.5 N•m (16.6-20.3 lb-ft)
7 Bolt (M10) . . . . . . . . 40 N•m (30 lb-ft)
8 Oil Pan
YAD1B5B0
SSANGYONG Y200
1B1-32 M162 ENGINE MECHANICAL
Removal & Installation Procedure
1. R e m o v e t h e d r a i n p l u g a n d d r a i n t h e o i l
completely.
2. Unscrew the bolts and remove the oil pan and
gasket.
Notice: Arrange the bolts according to each size.
3. Clean the inside of oil pan and sealing surface,
then apply the sealant.
4. Replace the gasket with new one.
5. Install the oil pan with gasket, and tighten each
bolt in specified torque.
6. Check for oil leaks while running the engine.
M8 X 40, 4 pieces
M6 X 85, 3 pieces
M6 X 35, 3 pieces
M6 X 22, 6 pieces
M6 X 20, 28 pieces
Others
YAD1B5C0
M162 ENGINE MECHANICAL 1B1-33
SSANGYONG Y200
TIMING GEAR CASE COVER
Preceding Work : Removal of cylinder head front cover
Removal of generator bracket
Removal of tensioning device
Removal of belt pulley and vibration damper
1 Bolt (M8 x 60, 3 pieces)
. . . . . . ... 22.5-27.5 N•m (16.6-20.3 lb-ft)
2 A/C Bracket
3 Bolt (M8 x 65, 3 pieces)
. . . . . . ... 22.5-27.5 N•m (16.6-20.3 lb-ft)
4 Bolt (M8 x 40, 1 piece)
. . . . . . ... 22.5-27.5 N•m (16.6-20.3 lb-ft)
5 Bolt (M8 x 60, 1 piece)
. . . . . . ... 22.5-27.5 N•m (16.6-20.3 lb-ft)
6 Seal
7 Timing Gear Case Cover
8 Roll Pin
9 Bolt (M6 x 22, 6 pieces)
. . . . . . . . . . .9-11 N•m (80-97 lb-in)
YAD1B690
SSANGYONG Y200
1B1-34 M162 ENGINE MECHANICAL
3. Remove the cooling fan and the viscous clutch.
Unscrew the three bolts from the cooling fan
bracket and remove the bracket.
Installation Notice
4. R e m o v e t h e t i m i n g g e a r c a s e c o v e r a f t e r
unscrewing the bolts (3) and (4) from the timing
gear case cover and the bolt (9) from the oil pan.
Notice: Be careful not to damage the oil pan
gasket.
Installation Notice
Removal & Installation Procedure
1. Put the alignment marks (arrows) on the timing
chain and camshaft sprocket.
2. Unscrew the A/C bracket bolts (1) and remove the
bracket.
Installation Notice
Tightening Torque
22.5 - 27.5 N•m
(16.6 - 20.3 lb-ft)
Tightening Torque
22.5 - 27.5 N•m
(16.6 - 20.3 lb-ft)
•
Apply the sealant after cleaning the timing gear
case cover surface.
•
Be careful not to stain the oil chamber of chain
tensioner with the sealant.
5. Installation should follow the removal procedure
in the reverse order.
6. Warm up the engine and check for oil leaks.
Tightening Torque
Bolt (3, 4) :
22.5 - 27.5 N•m
(16.6 - 20.3 lb-ft)
Bolt (9) :
9 - 11 N•m
(80 - 97 lb-in)
YAD1B590
YAD1B700
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст