SsangYong Rexton. Service manual — part 308
M162 ENGINE MECHANICAL 1B1-35
SSANGYONG Y200
CRANKSHAFT SEALING REAR COVER
Preceding Work : Removal of the automatic transmission drive plate
1 Bolt (M6 x 20, 6 pieces)
. . . . . . . . . . . 9-11 N•m (80-97 lb-in)
2 Radial Shaft Seal
3 Rear Cover
4 Sleeve
5 Bolt (M6 x 85, 2 pieces)
. . . . . . . . . . .9-11 N•m (80-97 lb-in)
6 Washer
YAD1B710
SSANGYONG Y200
1B1-36 M162 ENGINE MECHANICAL
Tools Required
601 589 03 43 00
Crankshaft Rear Seal Installer
Removal & Installation Procedure
1. Unscrew the bolts (1) and (5) and remove the
closing cover by pulling the rear cover lug (arrows).
Notice: Be careful not to damage the oil pan
gasket.
7. Install the crankshaft sealing rear cover mounting
bolts and remove the crankshaft rear seal installer
601 589 03 43 00.
Installation Notice
2. Clean the sealing surface of the crankcase and
the rear sealing cover.
3. Check the radial shaft seal and replace it if
necessary.
4. Apply the Loctite 573 to the rear cover sealing
surface.
5. Apply the engine oil to the dust lip of the radial
shaft seal.
Notice: Do not use the grease.
6. Install the crankshaft rear radial seal and the
crankshaft sealing rear cover, using crankshaft rear
seal installer 601 589 03 43 00.
Tightening Torque
9 - 11 N•m
(80 - 97 lb-in)
YAD1B740
YAD1B750
YAD1B760
YAD1B770
M162 ENGINE MECHANICAL 1B1-37
SSANGYONG Y200
1 Center Bolt (M18 x 50)
. . .. 1st step
180- 220 N•m (133-162 lb-ft)
. . .. 2nd step 90°+10°
2 Vibration Damper Disk
3 Bolt (M6 x 20, 6 pieces)
. . . . . . . 7.7-9.5 N•m (68.1-84.1 lb-in)
CRANKSHAFT ASSEMBLY
BELT PULLEY AND VIBRATION DAMPER
Preceding Work : Removal of cooling fan and viscous clutch
Removal of fan shroud
Removal of drive belt
4 Vibration Damper Assembly
5 Woodruff Key
6 Bolt (M6 x 12, 4 pieces)
. . . . . . . . . ... 9-11 N•m (80-97 lb-in)
7 Cooling Fan Pulley
YAD1B650
SSANGYONG Y200
1B1-38 M162 ENGINE MECHANICAL
Components
1 Center Bolt (M18 x 50)
2 Vibration Damper Disk
3 Vibration Damper and Pulley Assembly
4 Woodruff Key
5 Crankshaft Front Seal
6 Timing Gear Case Cover
7 Crankshaft Sprocket (Camshaft Driven)
8 Crankshaft Sprocket (Oil Pump Driven)
9 Crankshaft
10 Oil Pan
11 Oil Pan Gasket
12 Oil Pan Mounting Bolt (M6 x 22)
Service Data Standard
Permissble Deviation of The Vibration Damper
Radial Runout
Axial Runout
0.6 mm
0.6 mm
YAD1B660
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст