SsangYong Rexton. Service manual — part 607
SSANGYONG Y200
5D2-76 TRANSFER CASE - TOD
03E-019
YAD5D370
YAD5D380
YAD5D390
DISASSEMBLY PROCEDURE
1. Disconnect transfer case from vehicle
2. Using a 30 mm thin-wall socket, first remove the
rear output nut, output shaft yoke washer, oil seal
then the case flange.
3. Disconnect shift motor/clutch coil connector and
speed sensor connector from upper bracket of
transfer case.
N o t i c e : W h e n d i s c o n n e c t c o n n e c t o r , p u l l
forwards grasping connector housing.
4. Remove outer tube on speed sensor connector.
5. Remove wire supporting cape back side of speed
sensor connector.
7. Remove shift motor.
Notice: When remove shift motor, pay attention
to the location of triangular slot and shaft in transfer
case inside motor.
6. Disconnect pin of clutch coil wire (yellow) from
speed sensor connector (7 pin) using long-nose
plier.
TRANSFER CASE - TOD 5D2-77
SSANGYONG Y200
8. Disconnect front and rear speed sensor as
needed.
9. Remove the 17 bolts that retain the front case to
the rear case.
17. Remove the three nuts and washers retaining the
clutch coil assembly to the rear case.
18. Pull the assembly, along with the O-ring and wire,
from the case.
10. Make sure that the front case is facing downward
so that the rear cover is facing upwards.
11. Remove the rear front case from the rear case.
12. Remove all traces of gasket sealant from the
mating surfaces of the front case and rear case.
13. If the speedometer drive gear is to be replaced,
first remove the flange seal by prying and pulling
the curved-up lip of the flange seal.
Notice: Be careful not to damage the bearing,
bearing cage or case. Remove and discard the
flange seal.
14. Remove the speedometer drive gear and upper
tone wheel.
15. If the rear output shaft bearing requires replacing,
remove the internal snap ring that retains the
bearing in the bore.
16. From the outside of the case, drive out the bearing
using the driver.
YAD5D400
YAD5D410
YAD5D420
SSANGYONG Y200
5D2-78 TRANSFER CASE - TOD
YAD5D430
YAD5D440
YAD5D450
YAD5D460
19. Remove bearing assembly from output shaft.
20. Remove the clutch housing from the output shaft.
26. Remove the magnet from the slot in the front of the
case bottom.
27. Remove the output shaft and oil pump as an
assembly.
28. If required, to remove the pump from the output
shaft, rotate the pump to align.
29. Pull out the shift rail.
30. Remove the helical cam from the front case.
31. If required, remove the helical cam, torsion spring
and sleeve from the shaft.
24. Remove the chain, driven sprocket and drive
sprocket as an assembly.
25. Remove thrust washer from output shaft.
21. Remove the balls and apply cam and wave
washer from the output shaft.
22. Remove snap ring from output shaft.
23. Remove clutch pack assembly from output shaft.
TRANSFER CASE - TOD 5D2-79
SSANGYONG Y200
YAD5D470
YAD5D480
YAD5D490
42. Inspect the bushing and needle bearing in the end
of the input shaft for wear or damage.
Notice: Under normal use, the needle bearing
and bushing should not require replacement. If
replacement is required, the bushing and needle
bearing must be replaced as a set.
32. Remove the high-low range shift fork and collar
as an assembly.
33. Expand the tangs of the large snap ring in the
case.
34. With the input shaft against a bench, push the case
down and slide the main drive gear bearing
retainer off the bearing.
35. Lift the input shaft and front planet from the case.
36. If required, remove the oil seal from the case by
prying and pulling on the curved-up lip of the oil
seal.
Notice: Be careful not to damage the bearing,
bearing cage or case.
40. Place the input shaft in a vise and remove the
bearing.
41. Remove the thrust washer, thrust plate and the sun
gear off the input shaft.
37. Remove the internal snap ring from the planetary
carrier.
38. Separate the front planet from the input shaft.
39. Remove the external snap ring from the input shaft.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст