SsangYong Rexton. Service manual — part 372
SSANGYONG Y200
1B3-64 DIESEL ENGINE MECHANICAL
YAD1BE60
YAD1BE70
YAD1BE80
YAD1BE90
Tools Required
601 589 03 43 00
Oil Seal Assembler
602 589 00 40 00
Engine Lock
Removal Procedure
1. Install the engine lock 602 589 00 40 00.
2. Remove the 12-sided stretch bolts.
Notice: Remove the flywheel and drive plate, if
equipped with automatic transmission.
3. Remove the bolts (3. 6) from end cover, by pulling
out the lug (arrow), remove the cover.
Notice: Be careful not to damage the oil pan
gasket.
4. Remove the radial seal (4) with care not to damage
the sealing surface.
Notice: If the length ‘L’of bolts exceeds 22.5 mm,
replace the bolts.
DIESEL ENGINE MECHANICAL 1B3-65
SSANGYONG Y200
;;;;;
;;;;;
;;;;;
;;;;
;;;;
;;;;
;;;
;;;
;;;
;;;
YAD1BEA0
YAD1BEB0
YAD1BEC0
YAD1BED0
Installation Procedure
1. Throughly clean the sealing surface of end cover
and apply Loctite 573.
2. Clean the groove of radial seal.
3. Apply Loctite 573 on the bolts and install the end
cover.
Installation Notice
4. Install the inner oil seal assembler 601 589 03 43
00 to the crankshaft flange.
5. Coat a little oil on the sealing lip of new radial seal
and contacting surface.
Notice: Don’t use grease.
6. Insert the new radial seal (4) on to the oil seal
assembler 601 589 03 43 00 (7).
Notice: The sealing lip of the repair radial seal is
offset to the inside by 3 mm to ensure that is does
not run in any groove which the standard radial
seal may have left on the crankshaft flange.
Be careful not to damage the oil pan gasket.
Tightening Torque
10 N•m (89 lb-in)
A
Standard Radial Seal
B
Repair Radial Seal
SSANGYONG Y200
1B3-66 DIESEL ENGINE MECHANICAL
;;
;;
;;
;;
;;
;;
;;
;;
;;
;;
;;
;;
;;
;;
;;
;;
;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
;;;;;
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
yyyyy
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
;;;;
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
yyyy
YAD1BEE0
YAD1BEF0
7. Install the outer oil seal assembler 601 589 03 43
00 on the seal and by tightening the bolts, press
the radial seal into the end cover as far as the
stop.
Notice: The seal must be positioned exactly at
right angles in the end cover to ensure that it
provide a proper seal.
8. Install the flywheel.
Installation Notice
Tightening Torque
45 N•m (33 lb-ft)+ 90°
YAD1BEG0
DIESEL ENGINE MECHANICAL 1B3-67
SSANGYONG Y200
CRANKSHAFT BALL BEARING
YAD1BEH0
Notice: Manual transmission only.
Tools Required
000 589 25 33 00
Internal Extractor
000 589 33 33 00
Counter Support
Removal & Installation Procedure
1. Remove the manual transmission.
2. Using a internal extractor 000 589 25 33 00 and
counter support 000 589 33 33 00, pull out the
locking ring and ball bearing together.
3. Apply Loctite 241 on the new ball bearing and then
insert the ball bearing to be stopped at the spacer
ring by using a proper mandrel.
1 Spacer
2 Cover . . . . . . . . . . . . . .. Replace
3 Ball Bearing
4 Bolt . . . . . . . . .. 45 N•m (33 lb-ft)+ 90°
YAD1BEJ0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст