Jaguar X-Type Sedan and Estate (Wagon). Service manual — part 246
4.
CAUTION: Do not over tighten the drain plug. Failure to follow this
instruction may cause damage to the vehicle.
Install the drain plug when all coolant has drained.
Tighten to 1 Nm.
Remove the drain tray.
5. Install the undertray. For additional information, refer to Section
501-02
Front End Body Panels
.
6. Lower the vehicle.
7. Remove the engine cover.
8. Fill the cooling system up to the MAX mark on the coolant expansion
tank using a 50% mixture of Jaguar Premium Cooling System Fluid or
equivalent, meeting Jaguar specification ESE-M97B44-A and 50%
distilled water.
9. Install the coolant expansion tank pressure cap.
10. NOTE: During this procedure the thermostat should open.
START and RUN the engine at 2000 rpm until the cooling fan operates.
11. Stop the engine and allow to cool for two minutes.
12. Loosely install a pipe clamp to the heater inlet hose.
13. Loosely install a pipe clamp to the heater return hose.
14. START and RUN the engine at 2000 rpm.
15. With the engine at 2000 rpm, fully clamp the heater outlet hose and
then fully clamp the heater inlet hose.
16. Continue to run the engine for a further two minutes.
17. Switch the engine off.
18. Remove the heater hose clamps.
19. Fit the engine cover.
20. Allow the vehicle to cool to room temperature.
21. Remove the coolant expansion tank pressure cap, top up the coolant
level to the MAX mark on the coolant expansion tank.
22. Install the coolant expansion tank pressure cap.
Published: 11-May-2011
Engine Cooling - 2.0L NA V6 - AJV6/2.5L NA V6 - AJV6/3.0L NA V6 - AJ27 - Cooling
System Flushing
General Procedures
• NOTE: To remove rust, sludge and other foreign material from the cooling system, use Premium Cooling System flush, meeting Jaguar
specification EGR-M14P7-A, which is safe for use with aluminium cooling systems. This cleaning restores cooling system efficiency and helps
prevent overheating.
• NOTE: In severe cases where cleaning solvents will not properly clean the cooling system, it will be necessary to use the pressure flushing
method using Cooling System Flusher, 164-R3670 to restore efficient operation.
• NOTE: A pulsating or reversed direction of flushing water will loosen sediment more quickly than a steady flow in the normal coolant flow
direction.
• NOTE: Dispose of old coolant and flushing water contaminated with coolant and cleaning chemicals in accordance with local, state and
federal laws.
1. Remove the air cleaner. For additional information, refer to Section
303-12A Intake Air Distribution and Filtering
Section
303-12B Intake Air
Distribution and Filtering
.
2. Remove the thermostat. For additional information, refer to
Thermostat
.
3. Detach the lower coolant hose from the radiator and position to one
side.
4. Lower the vehicle.
5. Detach the upper coolant hose from the radiator.
6. Connect a hose pipe to the radiator upper coolant hose connection
using a suitable connector.
7.
CAUTION: Radiator internal pressure must not exceed 100 kPa
(14.5 psi). Failure to follow this instruction may cause damage to the
radiator.
Flush the radiator using the hose pipe until the coolant flowing from the
radiator lower coolant hose connection is clear.
8. Remove the hose pipe from the radiator upper coolant hose connection.
9. Connect a hose pipe to the upper coolant hose using a suitable
connector.
10. Flush the engine using the hose pipe until the coolant flowing from the
radiator lower coolant hose is clear.
11. Remove the hose pipe from the upper coolant hose connection.
12. Connect the upper coolant hose to the radiator.
13. Install the thermostat. For additional information, refer to
Thermostat
.
14. Fill the cooling system. For additional information, refer to
Cooling
System Draining, Filling and Bleeding
.
15. Install the undertray. For additional information, refer to Section
501-02 Front End Body Panels
.
16. Install the air cleaner. For additional information, refer to Section
303-12A Intake Air Distribution and Filtering
Section
303-12B Intake Air
Distribution and Filtering
.
Published: 11-May-2011
Engine Cooling - 2.0L NA V6 - AJV6/2.5L NA V6 - AJV6/3.0L NA V6 - AJ27 - Block
Heater
Removal and Installation
Removal
1. Drain the cooling system. For additional information, refer to
Cooling
System Draining, Filling and Bleeding
.
2. Disconnect the block heater electrical connector.
3. Remove the block heater.
Installation
1. To install, reverse the removal procedure.
Tighten to 40 Nm.
2. Fill the cooling system. For additional information, refer to
Cooling
System Draining, Filling and Bleeding
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст