Jaguar X-Type Sedan and Estate (Wagon). Service manual — part 383
Published: 11-May-2011
Automatic Transmission/Transaxle - Vehicles With: 6-Speed Automatic Transaxle -
AWF21 - Torque Converter
Removal and Installation
Removal
1. Raise and support the vehicle.
2. Remove the transmission.
For additional information, refer to:
Transmission
(307-01B Automatic
Transmission/Transaxle - Vehicles With: 6-Speed Automatic Transaxle -
AWF21, Removal).
3. NOTE: Some variation in the illustrations may occur, but the essential
information is always correct.
Using the special tools, remove the torque converter.
Installation
1. CAUTIONS:
Align the torque converter and oil pump drive before installing the
torque converter.
Make sure that the mating faces are clean and free of foreign
material.
Take extra care when handling the component.
Install the torque converter.
2. Install the transmission.
For additional information, refer to:
Transmission
(307-01B Automatic
Transmission/Transaxle - Vehicles With: 6-Speed Automatic Transaxle -
AWF21, Removal).
Published: 11-May-2011
Automatic Transmission/Transaxle - Vehicles With: 6-Speed Automatic Transaxle -
AWF21 - Torque Converter Seal
Removal and Installation
Removal
1. Raise and support the vehicle.
2. Remove the torque converter.
For additional information, refer to: Torque Converter (307-01, Removal
and Installation).
3. Carefully remove and discard the torque converter seal.
Installation
1. CAUTIONS:
Extreme cleanliness must be exercised when handling this
component.
Make sure that the mating faces are clean and free of foreign
material.
Using the special tool, install a new torque converter seal.
2. CAUTIONS:
Align the torque converter and oil pump drive before installing the
torque converter.
Make sure that the mating faces are clean and free of foreign
material.
Take extra care when handling the component.
Install the torque converter.
For additional information, refer to: Torque Converter (307-01, Removal
and Installation).
Published: 11-May-2011
Automatic Transmission/Transaxle - Vehicles With: 6-Speed Automatic Transaxle -
AWF21 - Turbine Shaft Speed (TSS) Sensor
Removal and Installation
Removal
1. Remove the main control valve body.
For additional information, refer to:
Main Control Valve Body
(307-01B
Automatic Transmission/Transaxle - Vehicles W ith: 6-Speed Automatic
Transaxle - AW F21, In-vehicle Repair).
2. Remove the turbine shaft speed (TSS) sensor.
Remove the bolt.
Release the sensor from the transmission.
Installation
1. To install, reverse the removal procedure.
Tighten to 6 Nm.
Published: 11-May-2011
Automatic Transmission/Transaxle - Vehicles With: 6-Speed Automatic Transaxle -
AWF21 - Transmission
Removal
Special Tool(s)
Impulse extractor
100-012(LRT-99-004)
Slide Hammer Shaft -
100-012-02
Halfshaft Remover Fork -
204-226
Power train assembly jack
HTJ1200-2
Engine support bracket
303-021
Removal
1. Disconnect the battery ground cable.
For additional information, refer to:
Battery Disconnect and Connect
(414-01 Battery, Mounting and Cables, General Procedures).
2. Remove the battery tray.
For additional information, refer to:
Battery Tray
(414-01 Battery,
Mounting and Cables, Removal and Installation).
3. Raise the vehicle.
4. Remove the front subframe.
For additional information, refer to:
Front Subframe - 2.0L Duratorq-
TDCi/2.2L Duratorq-TDCi (110kW /150PS) - Puma
(502-00 Uni-Body,
Subframe and Mounting System, Removal and Installation).
5. Drain the transmission fluid.
For additional information, refer to:
Transmission Fluid Drain and Refill
(307-01B Automatic Transmission/Transaxle - Vehicles W ith: 6-Speed
Automatic Transaxle - AWF21, General Procedures).
6.
CAUTION: Make sure the halfshaft constant velocity (CV) joints do
not over articulate. Failure to follow this instruction may result in damage
to the CV joints.
Release the RH halfshaft.
Release the RH halfshaft from the transmission.
Secure the RH halfshaft to one side.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст