Jaguar X-Type Sedan and Estate (Wagon). Service manual — part 410
Published: 11-May-2011
Manual Transmission/Transaxle - Halfshaft Seal LH
In-vehicle Repair
Special Tool(s)
Link shaft oil seal installer
205-115
Pinion oil seal remover
308-208
Removal
1. Drain the transmission.
For additional information, refer to:
Transaxle Draining and Filling -
Vehicles W ith: 5-Speed Manual Transmission - MT75
(308-03 Manual
Transmission/Transaxle, General Procedures) /
Transaxle Draining and Filling - Vehicles W ith: 6-Speed Manual
Transaxle - MMT6
(308-03 Manual Transmission/Transaxle, General
Procedures).
2. Remove the left-hand halfshaft.
For additional information, refer to:
Front Halfshaft LH
(205-04 Front
Drive Halfshafts, Removal and Installation).
3. Using the special tool, remove the halfshaft oil seal.
Installation
1. Using the special tool, install the halfshaft oil seal.
2. Install the left-hand halfshaft.
For additional information, refer to:
Front Halfshaft LH
(205-04 Front
Drive Halfshafts, Removal and Installation).
3. Refill the transmission.
For additional information, refer to:
Transaxle Draining and Filling -
Vehicles W ith: 5-Speed Manual Transmission - MT75
(308-03 Manual
Transmission/Transaxle, General Procedures) /
Transaxle Draining and Filling - Vehicles W ith: 6-Speed Manual
Transaxle - MMT6
(308-03 Manual Transmission/Transaxle, General
Procedures).
Published: 11-May-2011
Manual Transmission/Transaxle - Halfshaft Seal RH
In-vehicle Repair
Special Tool(s)
Link shaft oil seal installer
205-115
Pinion oil seal remover
308-208
1. Drain the transmission.
For additional information, refer to:
Transaxle Draining and Filling -
Vehicles W ith: 5-Speed Manual Transmission - MT75
(308-03 Manual
Transmission/Transaxle, General Procedures) /
Transaxle Draining and Filling - Vehicles W ith: 6-Speed Manual
Transaxle - MMT6
(308-03 Manual Transmission/Transaxle, General
Procedures).
2. Remove the right-hand halfshaft.
For additional information, refer to:
Front Halfshaft RH - 2.0L NA V6 -
AJV6/2.5L NA V6 - AJV6/3.0L NA V6 - AJ27
(205-04 Front Drive
Halfshafts, Removal and Installation) /
Front Halfshaft RH - 2.0L Duratorq-TDCi/2.2L Duratorq-TDCi
(110kW/150PS) - Puma
(205-04 Front Drive Halfshafts, Removal and
Installation).
Removal
1. NOTE: Left-hand shown, right-hand similar.
Using the special tool, remove the halfshaft oil seal.
Installation
1. Using the special tool, install the halfshaft oil seal.
2. Install the right-hand halfshaft.
For additional information, refer to:
Front Halfshaft RH - 2.0L NA V6 -
AJV6/2.5L NA V6 - AJV6/3.0L NA V6 - AJ27
(205-04 Front Drive
Halfshafts, Removal and Installation) /
Front Halfshaft RH - 2.0L Duratorq-TDCi/2.2L Duratorq-TDCi
(110kW/150PS) - Puma
(205-04 Front Drive Halfshafts, Removal and
Installation).
3. Refill the transmission.
For additional information, refer to:
Transaxle Draining and Filling -
Vehicles W ith: 5-Speed Manual Transmission - MT75
(308-03 Manual
Transmission/Transaxle, General Procedures) /
Transaxle Draining and Filling - Vehicles W ith: 6-Speed Manual
Transaxle - MMT6
(308-03 Manual Transmission/Transaxle, General
Procedures).
Published: 11-May-2011
Manual Transmission/Transaxle - Input Shaft Seal
In-vehicle Repair
Removal
1. Remove the clutch slave cylinder.
For additional information, refer to:
Clutch Slave Cylinder - Vehicles
W ith: 5-Speed Manual Transmission - MT75
(308-02 Clutch Controls,
Removal and Installation) /
Clutch Slave Cylinder - Vehicles W ith: 6-Speed Manual Transaxle - MMT6
(308-02 Clutch Controls, Removal and Installation).
.
Installation
Vehicles with 5-speed manual transaxle
1. NOTE: Apply suitable tape to the input shaft to protect the slave
cylinder seal from damage. Remove the tape when the slave cylinder is
installed.
• NOTE: Apply sealer to the mating faces of the clutch slave cylinder and
the transmission housing.
To install, reverse the removal procedure.
Tighten to 10 Nm.
Vehicles with 6-speed manual transaxle
2. NOTE: Apply suitable tape to the input shaft to protect the slave
cylinder seal from damage. Remove the tape when the slave cylinder is
installed.
• NOTE: Apply sealer to the mating faces of the clutch slave cylinder and
the transmission housing.
Tighten to 10 Nm.
Name
Gasket Eliminator Sealant
Published: 11-May-2011
Manual Transmission/Transaxle - Selector MechanismVehicles With: 5-Speed Manual
Transmission - MT75
In-vehicle Repair
Special Tool(s)
Engine Support Beam
303-021
Engine Support Brackets
303-1068
Engine lifting eye
303-1067
Gearshift selector setting tool
308-436
Materials
Specification
WSK-M2G348-A5
Removal
All vehicles
1. Detach the gearshift lever surround.
2. Remove the air cleaner. For additional information, refer to:
Air Cleaner
(303-12A Intake Air Distribution and Filtering - 2.0L NA
V6 - AJV6/2.5L NA V6 - AJV6/3.0L NA V6 - AJ27, Removal and
Installation),
Air Cleaner
(303-12B Intake Air Distribution and Filtering - 2.0L
Duratorq-TDCi/2.2L Duratorq-TDCi (110kW /150PS) - Puma, Removal
and Installation).
3. Remove the battery tray.
For additional information, refer to:
Battery Tray
(414-01 Battery,
Mounting and Cables, Removal and Installation).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст