Jaguar X-Type Sedan and Estate (Wagon). Service manual — part 583
it may be necessary to reduce the system volume slightly when using certain mobile phones.
Phone related messages are shown on the audio unit panel display or touch-screen when the phone system is active. The Bluetooth™
telephone system can be used in conjunction with the Voice Activation system to provide the driver with completely hands-free
communication. Voice commands are picked up by the system microphone.
The cellular phone system comprises the following components:
Bluetooth™ phone module
Microphone
Bluetooth™ antenna.
Phone dialling is achieved using one of the following methods:
Dialling a number using the audio unit or touch screen
Selecting a number from the handsets phonebook via the audio unit and the Bluetooth™ phone module
Selecting from the handsets call register via the Bluetooth™ phone module.
The Bluetooth™ phone module is connected to the Information and Entertainment system on the D2B bus. This allows audio and control
signals to be routed to and from the Bluetooth™ phone module. The Bluetooth™ phone module has a separate integral Bluetooth™ antenna
located on the
LH
side of the luggage compartment on wagon vehicles and on the rear parcel shelf on 4 door vehicles.
Telephone handsets must be paired with the Bluetooth™ phone module before they can be used with the vehicle system. Up to 5 telephone
handsets can be paired with the vehicle, but only 1 telephone can used at a time. If more than one phone is present in the vehicle, the last
connected phone will be given priority on connection. Phone connection is active at ignition on. The phone will be disconnected 6 minutes
after the ignition is switched off.
Phonebook and last number redial list are stored & synchronized for each of the 5 phones and are resynchronized when each phone
reconnects.
Bluetooth™ Phone Module
The Bluetooth™ phone module is located in the rear
LH
side of the luggage compartment. The Bluetooth™ phone module is connected on
the D2B ring to the voice control module. The D2B ring allows control instructions and audio to be transferred to the relevant modules.
Microphone
The microphone is located adjacent to the overhead console which surrounds the front interior lamp. The microphone is hardwired to the
voice module and the Bluetooth™ phone module.
Telephone Control Switches
Item
Part Number
Description
1
-
Rotary Volume control
2
-
Rotary control Telephone mode - scroll through stored numbers
3
-
Phone mode select button
4
-
Start voice mode button, answer telephone or send/end in phone mode
The telephone switches are located on the
LH
side of the steering wheel. Two rotary thumbwheels operate the volume of the selected audio
function including the telephone and also allow the driver to scroll through stored telephone numbers when in phone mode or select radio
stations or CD's when in audio modes. The 'source' switch allows the driver to select phone mode by pressing the switch for 2 seconds. The
switch can also be used to cycle through the AM, FM radio stations and CD's in the auto changer. The voice button will allow the start of the
voice function or mute when voice system is not fitted and also answer a call when phone ringing and also send/end when in a phone call.
Bluetooth™ Antenna
The Bluetooth™ antenna is located on the
LH
side of the luggage compartment on wagon vehicles and on the rear parcel shelf on 4 door
vehicles. The antenna is used to connect the Bluetooth™ phone module to a Bluetooth™ compatible phone.
Telephone Voice Control
The vehicle system is able to use any voice tags which are stored in the Jaguar Voice system. There is no voice dialling feature of the
cellular telephone system. Voice dialling is accessed via a short press of the voice button on the
LH
side of the steering wheel. Refer to the
Owners Handbook for further details on voice operation.
Published: 11-May-2011
Cellular Phone - Cellular Phone
Diagnosis and Testing
Principle of Operation
For a detailed description of the phone system, refer to the relevant Description and Operation sections in the workshop manual. REFER to:
Cellular Phone
(419-08 Cellular Phone, Description and Operation).
Inspection and Verification
Where a fault involving the cellular phone is indicated by the Jaguar Approved Diagnostic System, some basic diagnostic methods may be
necessary to confirm that connections are good and that the wiring is not damaged, before installing new components.
1. Verify the customer concern by operating the portable cellular phone both in portable mode and while connected to the vehicle.
1.
2. Make sure the portable convertible phone (US Only) is switched ON. W ith the power button ON, the system should be on while the
ignition switch is in ACC or RUN.
2.
3. Make sure the customer is calling within the coverage area. No Svc will appear in the display if the customer is calling from
outside the coverage area.
3.
4. Check to see if the Roam indicator is on. If so, follow the roaming instructions in the Cellular Phone User Guide.
4.
5. Check to see if the display reads Locked CDMA/TDMA or pin for GSM. If so, press Clr and enter the customer three-digit unlock
code for CDMA/TDMA or the customer pin number on the phone handset for GSM.
5.
6. Make sure the portable cellular phone (US Only) is securely seated in the holder.
6.
7. Make sure the GSM handset coil cord connector is correctly fitted to the armrest connector.
7.
8. Check the portable cellular phone (US Only) antenna connections.
8.
9. Check the portable cellular phone system registration (US Only). Also, check to make sure that the portable cellular phone is
correctly programmed. Incorrect programming can result in single system scanning, loss of speed dialing, loss of hands-free audio,
loss of auto redial, loss of dial tone multi-frequency tones, and the loss of other keypad/portable cellular phone functions.
9.
10. Make sure that a valid SIM card is inserted in the handset SIM card reader (GSM Only)
10.
11. Check the customer account status with the cellular carrier.
11.
If the customer concern is still present, follow these steps to diagnose the concern:
12. Visually inspect for obvious signs of mechanical or electrical damage:
12.
Visual Inspection Chart
Mechanical
Electrical
Portable cellular phone (US only)
Microphone
Portable cellular phone holder (US only)
Coil cord
Electrical connectors
W iring harness for damage or corrosion
Fuses
System/Carrier Concerns - All Systems
Dropped calls, bad connections, noisy audio and other intermittent symptoms usually indicate a system or cellular carrier concern, and are
not the fault of the phone itself. Such symptoms may occur in situations such as the following:
In certain geographic areas (for example: areas of excessive foliage or hills) or at the edge of coverage areas.
At the same place each day.
At the same time each day.
Under bridges, tunnels, in lower freeways, or in congested downtown areas.
If the customer phone exhibits any of the above symptoms or symptoms occur under the above conditions, the customer or the dealer
should contact customer assistance at their particular cellular provider/carrier or call the assistance number provided in the Jaguar Cellular
System Dealer kit.
Other Possible Concerns - All Systems
1. If, for some reason, the customer's electronic serial number was incorrectly recorded in the carrier switch, the phone will not work.
Call the assistance number provided in the Jaguar Cellular System Dealer kit to check the electronic serial number CDMA/TDMA
only.
1.
2. A customer initial call must be made in his/her home coverage area for correct activation of the Jaguar Cellular System.
2.
3. A customer may have to wait until after 24 hours of the coverage activation before making a call from outside of his/her home
coverage area or the phone might be reported stolen and coverage stopped.
3.
4. There may be a slight delay in activation after leaving the dealership from initial delivery.
4.
If, after checking these possibilities, the phone still does not function, do not attempt to repair the phone. Call the cellular phone
distributor.
DTC Index
CAUTION: W hen probing connectors to take measurements in the course of the pinpoint tests, use the adapter kit, part number
3548-1358-00
• NOTE: If the control module/component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty policy and
procedures manual (section B1.2), or determine if any prior approval program is in operation, prior to the installation of a new module or
component
• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the DMM leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines that involve pinpoint tests
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause.
Always check for loose connections and corroded terminals.
DTC
Description
Possible Source
Action
B1038 Microphone input circuit -
short to ground
Microphone fault
W iring harness
fault
Refer to appropriate circuit diagram, check microphone input circuits for short to
ground. Repair circuit faults using appropriate materials and methods. Clear DTC,
retest system to verify correct operation.
B1039 Microphone input circuit -
short to battery
Microphone fault
W iring harness
fault
Refer to appropriate circuit diagram, check microphone input circuits for short to
battery. Repair circuit faults using appropriate materials and methods. Clear DTC,
retest system to verify correct operation.
B1342 ECU is defective
Internal ECU
fault
This DTC also includes memory failure. Replace telephone ECU and clear DTC.
retest system to verify correct operation.
B1893 GPS antenna open circuit
GPS Antenna
W iring harness
fault
Check Antenna circuit for open circuits, repair wiring faults using approved
methods and materials, clear DTC and retest to confirm correct operation.
B2102 Antenna circuit short to
ground
GPS Antenna
W iring harness
fault
Check Antenna circuit for short circuits, repair wiring faults using approved
methods and materials, clear DTC and retest to confirm correct operation.
B2103 Antenna not connected
GSM or
Bluetooth
Antenna
W iring harness
fault
Check GSM and Bluetooth antenna circuits for open circuits, repair wiring faults
using approved methods and materials, clear DTC and retest to confirm correct
operation.
B2141 NVM configuration failure
No phone
number
invalid phone
number
Software error or SIM card error, confirm SIM is valid and download new software
to phone module. Clear DTC and retest system to confirm operation.
B2477 Module configuration
failure
Configuration
fault
No vehicle identification number present, configure vehicle. Clear DTC and recheck
system to confirm correct operation.
B2633 Microphone not
connected
Microphone
W iring harness
fault
Check microphone is connected correctly, Check microphone lines for open circuits.
install connectors correctly or repair wiring harness using appropriate methods and
materials.
B2636 SOS switch input short
circuit to ground
SOS switch
W iring harness
fault
Check SOS switch is not stuck. Check SOS switch input line for short circuit to
ground. Repair wiring harness faults using appropriate methods and materials.
Replace SOS switch as required. Clear DTC and retest system for correct operation.
B2637 Information switch input
short to ground
Information
switch
W iring harness
fault
Check information switch for faults, check wiring harness for information switch
circuits shorted to ground. Repair wiring harness faults using approved methods
and materials. Clear DTC and retest system for correct operation.
B2638 Phone rechargeable
battery fault
Phone battery
faulty
W iring harness
fault
Check if the phone battery is correct for the phone in use. Confirm battery
charging connections are in good condition and are connected to the power supply.
B2640 Deployment indication
input short to ground
W iring harness
Check wiring harness for airbag deployment indication circuit short to ground.
Repair wiring fault using approved methods and materials. Clear DTC and retest
system to confirm correct operation.
B2641 Deployment indication
input short to battery
W iring harness
Check wiring harness for airbag deployment indication circuit short to power.
Repair wiring fault using approved methods and materials. Clear DTC and retest
system to confirm correct operation.
B2904 Partial mute circuit
failure
W iring harness
Check mute circuits from phone ECU to radio head unit and nav system ECUs are
not short to ground. Repair wiring harness using approved methods and materials
U2601 D2B wake up short to
ground
W iring harness
Check D2B wake up circuit for short to ground. Repair W iring harness using
approved materials and methods. Clear DTC and retest to confirm correct
operation.
U2609 D2B wake up pulse width
out of specification
Module software
issue
D2B pulse width specification is <50mS - >110mS, if the pulse width is outside
this range check the module configuration and programming. Reconfigure and
reprogramme module, clear DTC and retest system to confirm correct operation.
U2610 D2B Slave ECU fails to
receive a report position
D2B network
concern
During initialisation no position status report is received, check D2B network for
open circuits, shorts. Repair wiring harness using approved methods and
materials. Clear DTC and retest system to ensure correct operation.
U2611 D2B Slave ECU fails to
receive an alarm clear
command
D2B network
concern
On entering alarm state, slave ECU has fail to receive alarm clear command, check
D2B network for open circuits, shorts. Repair wiring harness using approved
methods and materials. Clear DTC and retest system to ensure correct operation.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст