Chery QQ6 (Body Accessories and Dimensions). Service Instruction — part 2
17
3.9. Unclench the B pillar trim with a
right-angled screwdriver.
3.10. Take off the B pillar trim.
3.11. Remove the fix screws from the seat belt
with a cross screwdriver.
3.12. Loosen the fixing nuts with a 17# sleeve,
and then take off the seat belt.
4. Installation Step
The installing steps are reverse to those for
removal.
Note:
4.1. Keep the seat belt clean, avoid the oil stain,
and check whether the seat belt is damaged.
4.2. The pillar trim shall securely fit with the
body, without any loose symptoms; and the
trim shall fit well with the ceiling and rubber
strip.
4.3. The seat belt adjusting slide baffle on the B
pillar upper trim shall move freely, without any
influence on the adjustment of seat belt, and the
fit clearance of lower trim shall be even and
below 1mm;
4.4. The fit clearance between B pillar low trim
and front/rear scuff plate shall be even and less
than 1mm;
-------------------------------------------------------------------------------------------------------------------------------------------------------------
18
II. Disassembly/Reassembly of
Seat
Tool: 16# sleeve
1. Front passenger seat removal step
1.1. Pull the moveable handle under the left
seat to move the left seat backwards and reveal
the fixing bolts under the seat.
1.2. Remove two fixing bolts before the seat.
by sleeve
1.3. Turn the moveable handle and pull
forwards the seat, and expose two fixing bolts
on the rear of seat.
1.4 Disassemble two fixing bolts at the back
of seat with sleeve.
1.5 Pull off the inserter under seat and take
away the seat.
2. Rear passenger seat removal step
2.1 Lift up the rear passenger seat cushion by
hand, and then take out the cushion from the
clips of chassis and body.
2.2. Directly take out the seat cushion by both
hands.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
19
2.3. Loosen the front fixing bolts at the right
side of rear right seat with an open-end wrench.
2.4. Loosen the front fixing bolts at the left
side of rear right seat with an open-end wrench.
2.5. Pull up the ring-pull of rear right seat,
and lay down the seat forwards.
2.6. Loosen the rear fixing bolts at the right side
of rear right seat with an open-end wrench.
2.7. Loosen the rear fixing bolts at the left side
of rear right seat with an open-end wrench, and
then remove the rear right seat.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
20
2.8. Loosen the front fixing bolts of rear right
seat with a open-end wrench.
2.9. Pull up the ring-pull of rear left seat, and
lay down the seat forwards.
3.0. Loosen the rear fixing bolt of rear left seat
with a sleeve, and then remove the rear left
seat.
3. Installation Step
The installing steps are reverse to those for
removal.
Installation torque is 25±3Nm
III. Disassembly/Reassembly of
Console
Tool: cross head screwdriver
1. Removal Step
1.1. Remove each two bolts at left and right
sides with a cross screwdriver, these bolts of
which are used to joint the console and front
lower guard plate.
(The tightening torque is 2±0.5N.m)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
21
1.2. Remove the bolts used to joint the console
and body lower guard plate with a cross
screwdriver.
(The tightening torque is 2±0.5N.m)
1.3. Detach the console hand brake ornament
plate by hand.
1.4. Pull out the cigarette lighter plug on the
console by hand.
1.5. Take off the console.
2. Installation Step
The installing steps are reverse to those for
removal.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
22
IV. Disassembly/Reassembly of
Carpet
Tool: flat head screwdriver, cross head
screwdriver; sleeve
1. Removal Step
1.1. Remove the seat. (See Disassembly of
Seat)
1.2. Remove the scuff plate, lower trims of B
and C pillars.
(See Disassembly of B and C Pillars)
1.3. Remove the A pillar lower trim.
1.4. Remove the armrest box and console. (See
Disassembly of Armrest Box and Console)
1.5. Prize the cover on the driver pedal with flat
head screwdriver.
1.6. Remove two fixing nuts from the driver’s
pedal with a socket wrench, and then take off
the pedal.
Installation torque: 7±1N.m
1.7 Take off the carpet after Pull off the carpet
connectors
2. Installation Step
2.1. Place the carpet into the vehicle, tightedly
press the carpet near the central passage, and
expose the corresponding hole from the carpet
hole, and lay the carpet reliably.
2.2. Lay the left central rear part of carpet
according to the shape of the vehicle bottom,
and reveal the installation holes of front left
seat and lay the carpet reliably.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
23
2.3. Lay the right central rear part of carpet
according to the shape of the vehicle bottom,
and reveal the installation holes of front right
rear seat and lay the carpet reliably.
2.4. Lay well the rear part of carpet according
to the shape of vehicle bottom.
V. Removal of Cushion Pad
1. Removal Step
1.1. Disassemble the carpet (See disassembly of
carpet)
1.2. Take off all cushion pads.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
24
2. Installation Step
2.1. The installing steps are reverse to those for
removal.
2.2. Precautions on reassembly of cushion pad:
2.2.1. Take out the connector harness from the
seat and rear oxygen sensors when the cushion
pad is laid.
2.2.2. Make the shock absorber lower surface
joint tightly with plate work.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
25
Chapter 3 Removal and Maintenance of Door
I. Disassembly/Reassembly and Maitenance of Front Door
1. System Composition Diagram
-------------------------------------------------------------------------------------------------------------------------------------------------------------
26
2. Preparation
Tools:
right-angled
screwdriver,
cross
screwdriver, 7#, 10# and 13# sleeves, plier.
3. Precautions
3.1 Please wear necessary labor protection
supplies to avoid accidents.
3.2 Power off accumulator to avoid damage the
electrical units.
3.3 Use the correct method to disassemble and
assemble the glass to avoid damage.
4. Disassembly/Reassembly Step
4.1. Unclench the protecting cover of glass
drive switch on the door inner guard plate with
a right-angled screwdriver.
4.2. Pull out the connector from the glass drive
switch by hand..
4.3. Unscrew the fix screws of front door inner
handle with a cross screwdriver.
4.4. Take off the inner handle frame by both
hands.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
27
4.5. Separate the inner bar from the inner
handle with a right-angled screwdriver.
4.6. Remove the fix screws from the front door
inner guard plate with a cross screwdriver.
4.7. Lift up the door inner guard plate from the
lower to upper by both hands.
4.8. Directly take out the door inner guard plate
by both hands.
4.9. Tear down front door water-proof plastic
clothing.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
28
4.10. Take off the interior set square of the
exterior rear-view mirror by hand.
4.11. Pull out the connector of the exterior
rear-view mirror by hand.
4.12. Remove three fix screws from the exterior
rear-view mirror with a sleeve.
4.13 Remove three fix screws from the exterior
rear-view mirror with a sleeve.
4.14 Take off the exterior rear-view mirror assy
by hand.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
29
4.15. Unscrew four fixing screws from front
door sound box by cross head screwdriver.
Take out sound box assy.
4.16 Pull out the connector of the front door
sound box.
4.17 Reinsert the glass drive switch into the
harness, and descend the front door glass down
to its lowest position.
4.18. Loose two fixing screws on the glass by
cross head screwdriver.
And take out the glass assembly.
Torque: 4.5±0.5 N.m.
4.19 When the glass assy is being taken, erect
the glass assy so as to easily take off it.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
30
4.20 Remove six fixing bolts from the window
glass regulator with a 10# sleeve.
Torque: 9±1 N·m.
4.21 Pull out the connector of window glass
regulator by hand.
4.22 Take off the window glass regulator assy.
4.23 Separate the upper fixing clips of front
door lock core rod from the lock by hand.
4.24 Separate the lower fixing clips of front
door lock core rod from the lock by hand.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
31
4.25 Loosen the fix screws of front door
exterior handle with a sleeve.
4.26. Take out lock core and handle assy.
4.27 Remove three fix screws from the front
door lock core with a cross screwdriver.
Installation torque: 9±1 Nm
4.28 Pull out the fastener connector and then
take off the fastener.
4.29 Loosen two upper fixing bolts of front
door hinge from the door with a 13# wrench.
Torque: 36±4N.m.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
32
4.30 Loosen two lower fixing bolts of front
door hinge from the door with a 13# wrench.
Torque: 36±4N.m.
4.31 Remove the fixing bolts of door limiter
from the door with a 10# sleeve.
Torque: 10±1 N.m
4.32 Remove the fixing bolts of door limiter
from the body with a 10# sleeve, and then take
off the door limiter.
Torque: 10±1 N.m
4.33 Pull out the door harness, and then take off
the door body.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст