Chery Tiggo 5 (T21). Service manual — part 508
47–
48
47
6. Remove the left and right back-up light service covers.
a. Using a screwdriver wrapped with protective tape, pry
up the claws on back-up light service covers.
b. Remove the left back-up light service cover (1) and
right back-up light service cover (2).
7. Remove the back door grip assembly.
a. Remove the fixing screw (arrow) from the back door grip
assembly.
(Tightening torque: 7 ± 1 N·m)
b. Using a screwdriver wrapped with protective tape, pry
up the claw on back door grip assembly and remove
the back door grip assembly.
8. Remove the back door lower protector assembly.
a. Remove 6 fixing screws (1) and 4 plastic clips (arrow)
from the back door lower protector assembly.
(Tightening torque: 1.5 ± 0.5 N·m)
1
2
RT21470720
RT21470730
RT21470740
1
1
RT21470750
47–
49
47
b. Using an interior crow plate, pry off the clips from the
back door lower protector assembly.
c. Remove the back door lower protector assembly.
Installation
Installation is in the reverse order of removal.
RT21470760
CAUTION
Be sure to wear safety equipment to prevent accidents when installing back door protector assembly.
Try to prevent body paint surface from being scratched when installing back door protector assembly.
47–
50
47
Back Door Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the back door adjustment block.
a. Turn the back door adjustment blocks (1) counterclockwise and remove the back door adjustment
blocks.
4. Remove the back door buffer block.
a. Using a screwdriver wrapped with protective tape,
remove the back door buffer blocks (2).
5. Remove the back door locating seat.
a. Remove 4 fixing bolts (arrow) from the back door
locating seat.
(Tightening torque: 1.5 ± 1 N·m)
b. Remove the left back door locating seat (1) and right
back door locating seat (2).
WARNING
When removing back door assembly, an assistant is needed to hold back door. Prevent back door from
dropping or sudden closing to cause accidents during operation.
CAUTION
Be sure to wear safety equipment when removing back door assembly.
Try to prevent body paint surface from being scratched when removing back door assembly.
RT21470761
2
1
RT21480380
1
2
47–
51
47
6. Remove the left back door locating block (take left side as an example).
a. Remove 2 fixing bolts (arrow) from the back door
locating block.
(Tightening torque: 1.5 ± 1 N·m)
b. Remove the left back door locating block.
7. Remove the back door protector assembly (
).
8. Remove the rear wiper arm assembly (
9. Remove the rear wiper motor assembly (
).
10.Remove the rear nozzle assembly (
).
11.Remove the rear spoiler assembly (
).
12.Remove the back door upper trim board assembly (
).
13.Remove the back door lock assembly (
14.Remove the back door opener switch assembly (
15.Remove the rear combination light assembly (movable part) (
).
16.Remove the back door weatherstrip (
17.Remove the roof assembly (
).
HINT:
It is not necessary to remove the roof assembly completely, because the rear part of roof assembly needs
to be lowered for disconnecting the back door connector.
18.Remove the back door assembly.
a. Disconnect the back door connector (arrow).
b. Disconnect the washer line (1).
c. Using a screwdriver wrapped with protective tape, pry
off the back door air spring upper clips and remove
the back door air spring.
RT21470770
1
RT21470780
RT21470790
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст