Chery Tiggo 5 (T21). Service manual — part 62
06–
90
06
a. Check resistance of injector of cylinder 4.
a. Use X-431 3G diagnostic tester to read the ECM DTC.
b. Refer to "DTC Confirmation Procedure".
c. Check if DTC P0271-00 still exists.
6
Check injector of cylinder 4
1
2
RT21080290
-
+
Multimeter Connection
Specified
Condition
1 - 2
20 Ω (at 20°C)
Replace injector of cylinder 4
NG
7
Check for DTCs
OK
Replace ECM
NG
System is operating normally.
Reassemble vehicle and perform a road test to confirm that malfunction reported by customer has
been repaired.
OK
06–
91
06
SQR484F ENGINE MANAGEMENT SYSTEM
DTC
P1106-00 Throttle Pos. Contr. Malfunction
DTC
P1110-00 Throttle Actuator Electrical Malfunction (MT only)
DTC
P1111-00
Idle Speed Control Throttle Position Mechanical
Malfunction
DTC
P1568-00 DV-E Cause of Failure: Spring Check
DTC
P0606-00 ECM/PCM Processor
06–
92
06
ET21065006
37 38 39 40 41 42 43 44 45 46
47
48
25 26 27 28 29 30 31 32 33 34
35
36
13 14 15 16 17 18 19 20 21 22
23
24
1
2
3
4
5
6
7
8
9 10
11
12
B
E-035
1
4
2
5
3
6
1-23
1-11
1-22
1-14
1-43
1-13
RG
RL
RB
L
WL
RL
RG
RL
RB
R
WL
RL
ELECTRONIC
THROTTLE
M
8
5
7
4
6
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
31
35
39
40
41
42
32
33
36
37
38 34
27
28
29
30
B
E-007
E-007
E-038
1
2
3
4
5
6
B
E-009
E-009
ECM-1
E-035
06–
93
06
DTC Confirmation Procedure
Confirm that battery voltage is over 12 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC).
Turn ignition switch to ON.
Use X-431 3G diagnostic tester to record and clear the DTCs stored in the ECM.
Start the engine and warm it up to normal operating temperature, and then select Read Code.
If the DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis
procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent (
).
Diagnosis Procedure
a. Turn ignition switch to LOCK.
b. Check ECM grounds E-026 and E-028 (
DTC Code
DTC Definitions
DTC Detection
Conditions
Possible Cause
P1106-00
Throttle Pos. Contr.
Malfunction
Ignition switch ON
Electronic throttle
Wire harness or connector
ECM
P1110-00
Throttle Actuator
Electrical Malfunction
(MT only)
P1111-00
Idle Speed Control
Throttle Position
Mechanical
Malfunction
P1568-00
DV-E Cause of Failure:
Spring Check
P0606-00
ECM/PCM Processor
CAUTION
When performing circuit diagnosis and test, always refer to the circuit diagram for specific circuit and
component information.
1
Check ECM ground point
Repair or replace ground wire harness or
ground point
NG
2
Check electronic throttle connector
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст