Chery Tiggo 5 (T21). Service manual — part 309
28–
18
28
Disassembly
1. Remove the ignition starting switch.
a. Remove the fixing screws (arrow) from the ignition
starting switch, and then remove the ignition starting
switch.
(Tightening torque: 13 ± 2 N·m)
2. Remove the ignition switch illumination light.
a. Remove the ignition switch illumination light in the
direction of arrow from the ignition switch lock body.
3. Remove the ignition key cylinder.
a. Turn the ignition switch key cylinder to ACC with key,
and insert a small screwdriver or similar tool into the
ignition switch lock body hole, then pull out the ignition
key cylinder.
4. Remove the ignition switch lock body.
a. Set the steering column assembly onto a vise.
RT21280190
RT21280191
RT21280210
CAUTION
DO NOT tighten the vise excessively.
28–
19
28
b. Using an electric drill (1), drill a hole on the ignition
switch lock body anti-theft bolt (arrow).
c. Using a screw remover, remove the ignition switch
lock body anti-theft bolt.
d. Remove the ignition switch lock body and ignition switch fixing clamp.
Inspection
1. Check if ignition switch lock body and key cylinder are normal. Replace the ignition switch lock body and
key cylinder if necessary.
2. Check steering column assembly for wear, cracks or deformation, and welding or correction is not allowed.
Replace the steering column assembly if necessary.
3. Check steering column bearing for looseness, wear or sticking. Replace the steering column assembly if
necessary.
Assembly
1. Install the ignition switch assembly.
a. Set the steering column assembly onto a vise.
b. Install the ignition switch assembly to the steering
column assembly with a new ignition switch lock body
anti-theft bolt, and then tighten the anti-theft bolt until
its head is disengaged.
1
RT21280220
RT21280221
CAUTION
DO NOT tighten the vise excessively.
RT21280222
28–
20
28
2. Install the ignition key cylinder.
a. Push the ignition key cylinder into the ignition switch
lock body until the ignition key cylinder fixing block
locks in place.
b. Check the ignition key cylinder for proper operation. When the key is removed, steering lock is locked;
when the key is inserted and ignition switch is turned to ACC or ON, steering lock is unlocked.
Installation
Installation is in the reverse order of removal.
RT21280211
CAUTION
Before installing steering column assembly, slide the spline at lower part of steering column assembly
onto intermediate shaft upper universal joint first.
Tighten the fixing nuts, bolts and screws in place.
Install each connector in place.
28–
21
28
Electronic Power Steering Column with Intermediate Shaft
Assembly
Removal
1. Set steering wheel to straight-ahead position.
2. Turn off all the electrical equipment and ignition switch.
3. Disconnect the negative battery cable.
4. Remove the driver airbag (
).
5. Remove the steering wheel assembly (
6. Remove the combination switch cover (
).
7. Remove the spiral cable (
8. Remove the combination switch assembly.
a. Disconnect the light combination switch connector (1)
and wiper and washer combination switch connector
(2).
b. Loosen the combination switch clamp and pull the
combination switch outward, then disconnect the
combination switch from the steering column to
remove the combination switch.
9. Remove the lower left protector assembly (
).
10.Remove the brake pedal assembly (
11.Remove 3 steering boot nuts (arrow) from the front baffle
plate, and then loosen the worm clamp (1) to separate
the steering boot from the front baffle plate.
(Tightening torque for nut: 10 ± 1 N·m)
(Tightening torque for worm clamp: 2 ± 0.5 N·m)
2
1
RT21280230
0
E
C
X1000
rpm
0
1
2
3
4
5
6
7
8
H
km/h
20
40
60
80
100 120
140
160
180
200
220
F
L
R
ON
OFF
OFF
OFF
OFF
OFF
REAR
MIST
INT
INT
LO
HI
PULL
2
3
NAVI
RT21280131
1
RT21280170
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст