Peugeot 206 CC (2006 year). Instruction — part 3
33
-
Audio equipment and telematics
01-01-2006
RADIO
Notes on radio reception
Your car radio is subject to
phenomena which do not affect
domestic radio sets. Both AM (MW/
LW) and FM reception are subject to
various forms of interference. This
is no reflection on the quality of the
equipment, but is due to the nature of
the signals and the way in which they
are transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the
result of increasing distance from
the transmitter, deflection of the
signals by obstacles (mountains,
hills, buildings, etc.), or of being in
an area which is not covered by a
transmitter.
Selecting radio mode
Automatic station search
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons
H or I to switch the
function on or off.
Press button
O.
Press button
O briefly
to select wavebands
FM1, FM2, FMast and
AM.
Briefly press button
J or L to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the first station
found as soon as the button is
released.
If the
TA traffic programme is
selected, only stations broadcasting
this type of programme are selected.
Selecting a waveband
Manual station search
Press the
"MAN" button.
Briefly press button
J or L to
increase or decrease the frequency
displayed.
By continuing to press the button
in the direction selected, you will
obtain continuous scrolling of the
frequency.
The scrolling stops at the first station
found as soon as the button is
released.
Pressing the
"MAN" button again
returns you to automatic station
search.
Manual storing of stations in the
memory
Select the station required.
Press one of the buttons
"1" to "6"
for more than two seconds.
The sound stops then becomes
audible again, confirming that the
station has been stored in the
memory.
Searching for a station occurs first
in
"LO" sensitivity (selection of
the most powerful transmitters)
during scanning of the waveband,
then in
"DX" sensitivity (selection
of the weakest and most distant
transmitters).
To make a direct search in
"DX"
sensitivity, press button
J or L twice.
33
-
Audio equipment and telematics
01-01-2006
RADIO
Notes on radio reception
Your car radio is subject to
phenomena which do not affect
domestic radio sets. Both AM (MW/
LW) and FM reception are subject to
various forms of interference. This
is no reflection on the quality of the
equipment, but is due to the nature of
the signals and the way in which they
are transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the
result of increasing distance from
the transmitter, deflection of the
signals by obstacles (mountains,
hills, buildings, etc.), or of being in
an area which is not covered by a
transmitter.
Selecting radio mode
Automatic station search
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons
H or I to switch the
function on or off.
Press button
O.
Press button
O briefly
to select wavebands
FM1, FM2, FMast and
AM.
Briefly press button
J or L to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the first station
found as soon as the button is
released.
If the
TA traffic programme is
selected, only stations broadcasting
this type of programme are selected.
Selecting a waveband
Manual station search
Press the
"MAN" button.
Briefly press button
J or L to
increase or decrease the frequency
displayed.
By continuing to press the button
in the direction selected, you will
obtain continuous scrolling of the
frequency.
The scrolling stops at the first station
found as soon as the button is
released.
Pressing the
"MAN" button again
returns you to automatic station
search.
Manual storing of stations in the
memory
Select the station required.
Press one of the buttons
"1" to "6"
for more than two seconds.
The sound stops then becomes
audible again, confirming that the
station has been stored in the
memory.
Searching for a station occurs first
in
"LO" sensitivity (selection of
the most powerful transmitters)
during scanning of the waveband,
then in
"DX" sensitivity (selection
of the weakest and most distant
transmitters).
To make a direct search in
"DX"
sensitivity, press button
J or L twice.
34 - Audio equipment and telematics
01-01-2006
Automatic storing of FM stations
in the memory (autostore)
Press button
O down
for more than two
seconds.
Your radio automatically stores the
six stations with the strongest signal
in
FM. These stations are stored in
the FMast waveband.
If it is not possible to find 6 stations,
the remaining memories are empty.
RDS
Using the RDS (Radio Data
System) function on FM
Radio Data System allows you to
continue listening to the same station
whatever frequency it is using for the
region you are going through.
Traffic information programme
RDS station following
The display indicates the name of
the station selected. When the RDS
function is active, the radio continually
searches for the transmitter which
transmits the station selected with
the best reception.
Press the
"TA" button
to switch the function
on or off.
The multifunction display will show:
-
"TA" if the function is selected,
- "(TA)" if the function is selected but
not available.
Any traffic information flash will be
given priority, whatever source you
are listening to (radio, CD or CD
changer).
If you wish to interrupt a message,
press the
"TA" button; this switches
the function off.
Briefly
press
the
"RDS"
button
to
switch the function on
or off.
The multifunction display will show:
-
"RDS" if the function is selected,
-
"(RDS)" if the function is selected
but not available.
Recalling stations stored in the
memory
For each waveband, briefly press
one of the buttons
"1" to "6" to recall
the corresponding station.
Note : the volume of traffic
information announcements is
independent of the volume of
normal radio listening. You can
adjust it using the volume button.
The setting will be stored and will
be used when the next messages
are broadcast.
35
-
Audio equipment and telematics
01-01-2006
Regional following mode (REG)
When they are part of a network,
certain stations broadcast regional
programmes in the various areas
they serve. With regional following
mode you can keep listening to the
same programme.
Press the
"RDS" button for more than
two seconds to switch the function on
or off.
PTY function
This allows you to listen to stations
broadcasting a specific type of
programme (news, culture, sport,
rock etc.).
With
FM selected,
press the
"TA" button
for more than two
seconds to switch this
function on or off.
To search for a
PTY programme:
- select the
PTY function,
- briefly press button
J or L to scroll
down the list of the various types of
programmes offered,
- when the programme of your
choice is displayed, keep button
J or L pressed for more than two
seconds to carry out an automatic
search (after an automatic search
the
PTY function is switched off).
In
PTY mode the different types
of programmes can be stored
in memory. To do this, press the
preselection buttons
"1" to "6" for
more than two seconds. Briefly press
the corresponding button to recall
the type of programme stored in the
memory.
EON system
This connects stations which are part
of the same network. It enables the
broadcasting of traffic information or
a
PTY programme by a station that
is part of the same network as the
station to which you are listening.
This service is available when
you have selected the
TA traffic
information programme or the
PTY
function.
36 - Audio equipment and telematics
01-01-2006
Shuffle (RDM)
When the CD player is selected, keep
button
N pressed for two seconds.
The tracks will be played in random
sequence. Pressing the button again
for two seconds returns you to normal
play.
Shuffle mode is de-activated each
time the audio equipment is switched
off.
The use of copied com-
pact discs may cause
malfunctions.
Insert circular compact
discs only.
In the cabriolet position, remember
to remove the compact discs from
your player (risk of theft).
COMPACT DISC
Selecting CD mode
After insertion of a
disc, printed face
upwards, the player
starts automatically.
If a disc is already inserted, press
button
N.
Ejection of a disc
Press button
D to
eject the disc from the
player.
Press button
J to select the next
track.
Press button
L to return to the start
of the current track or to select the
previous track.
Selecting a track
Accelerated play
Keep button
J or L pressed for
forwards or backwards accelerated
play.
Accelerated play stops as soon as
the button is released.
37
-
Audio equipment and telematics
01-01-2006
Selecting a disc
Accelerated play
Keep button
J or L pressed for
forwards or backwards accelerated
play.
Accelerated play stops as soon as
the button is released.
Press button
M.
CD CHANGER
Selecting CD changer mode
Selecting a track
Press button
J to select the next
track.
Press button
L to return to the start
of the current track or to select the
previous track.
Press one of the buttons
"1" to "5" on
the radio to select the corresponding
disc.
The use of copied compact
discs may cause faults.
Insert circular compact
discs only.
5 CD CHANGER*
* According to country.
This is located in the glove box. It
holds up to 5 discs.
To load the changer, insert the discs
with the printed side upwards.
To remove a disc, press and hold one
of the buttons
"1" to "5".
Shuffle (RDM)
When the CD changer is selected,
keep button
M pressed down for two
seconds. The tracks will be played
in random sequence. Pressing the
button again for two seconds returns
you to normal play.
38 - Audio equipment and telematics
01-01-2006
Presentation
Your 206 CC is fitted with a JBL audio
system, designed specifically for the
vehicle's passenger compartment.
At the heart of the system, a 240
Watt multifunction amplifier (1),
incorporated in the subwoofer in
the boot, independently controls 8
high acoustic definition speakers
and the subwoofer.
This system makes it possible to
obtain optimum reproduction and
distribution of the sound in the
vehicle, in the two configurations
of the passenger compartment:
Coupé and Cabriolet.
The speakers are located:
- in the front door pillars: two
Tweeters (2) for reproduction of
the treble (high frequencies).
- in the front doors: two
Woofers (3)
for reproduction of the bass (low
frequencies).
- in the rear panels: two
Tweeters (4)
fitted in two
Woofers (5) for a bal-
ance of frequencies and sound
which fills the passenger compart-
ment.
- in the boot: one
Subwoofer (6)
incorporating two special woofers
for reproduction of the bass and ex-
treme bass (very low frequencies)
throughout the passenger compart-
ment.
You will appreciate the dynamics
and depth of the JBL system,
noticing that the sound fills the
vehicle perfectly.
AUDIO SYSTEM
Adjustment in CD and Radio
mode
The basic functions remain those of
the audio equipment.
No additional adjustment is required.
However, to benefit fully from your
JBL audio system, you are advised to
adjust the AUDIO functions
(BASS,
TREB, FAD, BAL) to position "0"
(zero) and the Loudness
(LOUD) to
the "
ON" position for the CD mode
or to the "
OFF" position for the radio
mode.
39
-
Audio equipment and telematics
01-01-2006
The remote control
Pointing this at the screen enables
the information contained in the
various menus to be selected.
THE SATELLITE NAVIGATION
SYSTEM
Introduction
The satellite navigation system
guides you to the destination of your
choice by means of vocal and visual
instructions.
The heart of the system lies in the
use of a map database and a GPS
system. The latter enables your
position to be located by means of
several satellites.
The satellite navigation system
consists
of
the
following
components:
- the remote control,
- the display,
- the control unit,
- the last voice message recall
control,
- the CD ROM,
- the multifunction aerial.
Some
functions
or
services
described may vary depending on
the CD-ROM version or the country
where the vehicle is sold.
menu : this button allows access
to the main menu. It can be
used at any time.
esc :
escape button
"Short press": cancels the
current operation and returns
to the previous screen.
"Press
for
more
than
2 seconds": returns to the
welcome screen.
This button can be used
in any menu. It is inactive
during guidance.
mod : mode button
"Short
press":
changes
between date, navigation,
radio
and
permanent
locating.
val :
Validation button
Confirms
the
function
selected.
A special compartment in the glove
box permits storage of the remote
control.
Reference of the 2 batteries:
1.5 volts type LR03.
Direction arrows:
These enable you to move around the
screen and thus select a function.
On the welcome screen only, the
up and down arrows enable the
brightness of the screen to be
adjusted.
The right and left arrows enable
the complete name of the road to
be displayed temporarily, during
guidance, if the name exceeds the
capacity of the screen.
40 - Audio equipment and telematics
01-01-2006
When the menus are used, the
functions which appear at the bottom
of the screen are presented in various
ways:
1. Function selected.
2. Function inaccessible in this
situation.
3. Function accessible.
Note: the "List" option is accessible
for a maximum of 80 possible
addresses.
The control unit
The display
During guidance the screen displays
different information depending on
the manoeuvres to be carried out:
1. Distance to next manoeuvre.
2. Next manoeuvre to be carried
out.
3. Next road to take.
4. Time.
5. Exterior temperature.
6. Current road.
7. Distance to final destination.
8. Manoeuvre to be carried out.
This is located in the glove box.
1. CD-ROM eject button.
2. CD-ROM compartment.
3. ON indicator light indicates that
the control unit is supplied with
power.
4. CD indicator light shows that
there is a CD-ROM in the unit.
5. Remote control storage
compartment.
41
-
Audio equipment and telematics
01-01-2006
Pressing the button on the end of
the lights stalk allows the last voice
message to be repeated, or, if
appropriate, a voice message to be
heard and a more detailed display
of the approaching landscape to be
displayed.
The last voice message recall
control
This contains all the mapping data.
It must be inserted with the printed
face upwards.
Use only CD-ROMs approved by
PEUGEOT.
The CD-ROM
The use of copied compact
discs may cause faults.
The satellite navigation system is
active when the globe is lit with a full
outline.
42 - Audio equipment and telematics
01-01-2006
Main menu
Switch on the ignition.
Press the
"Menu" button to access
the main menu.
Select a function using the direction
arrows, then confirm (
"VAL" button).
Navigation / Guidance
Following
selection
of
the
"Navigation/guidance" menu, a
screen warns you about the use of
the navigation system. Follow the
regulations in force and do not use
the remote control while driving.
Press the
"VAL" button to access
the next screen.
The
"Navigation/guidance" menu
offers the following options:
- entering of the address of a new
destination;
- selection of a service (hotel, station,
airport...) available in a town;
- selection of an address stored in
one of the two directories;
- access to the
"Navigation options"
menu.
- radio functions are suspended
when the system is in guidance
mode.
42 - Audio equipment and telematics
01-01-2006
Main menu
Switch on the ignition.
Press the
"Menu" button to access
the main menu.
Select a function using the direction
arrows, then confirm (
"VAL" button).
Navigation / Guidance
Following
selection
of
the
"Navigation/guidance" menu, a
screen warns you about the use of
the navigation system. Follow the
regulations in force and do not use
the remote control while driving.
Press the
"VAL" button to access
the next screen.
The
"Navigation/guidance" menu
offers the following options:
- entering of the address of a new
destination;
- selection of a service (hotel, station,
airport...) available in a town;
- selection of an address stored in
one of the two directories;
- access to the
"Navigation options"
menu.
- radio functions are suspended
when the system is in guidance
mode.
43
-
Audio equipment and telematics
01-01-2006
Entering a new destination
The last town entered is displayed.
To enter the name of another town,
select each letter using the direction
arrows then confirm (
"VAL" button)
for each letter.
If an error is made, the
"Correct"
function enables the last letter
entered to be cleared.
The
"List" function indicates, as the
name is entered, the number of towns
beginning with the same letters. If the
list contains less than 5 names, these
are displayed automatically. Select a
town then confirm (
"VAL" button).
The
"Change" function enables
the town entered to be completely
cleared.
When the complete name of the town
is displayed, select the
"Validate"
function then press the
"VAL"
button.
Note: following confirmation of a
letter, only those letters which could
make up an existing name appear.
Enter the name of the street. Select
the
"Validate" function then press
the
"VAL" button.
Note: the guidance can be activated
from the time the town is entered
without the name of a street or a
number. To do this, select the
"City
centre" function.
Enter the number on the street.
Select the
"Validate" function then
press the
"VAL" button.
Note: the guidance can be activated
as soon as the town and street are
entered without a number. To do this,
select the
"Validate" function.
44 - Audio equipment and telematics
01-01-2006
The complete destination is displayed.
Select the
"Validate" function then
press the
"VAL" button.
Note: you can also change the
destination or store it in one of the
two directories (see the section on
storing an address in a directory).
The last guidance criterion used is
displayed.
Guidance
begins
automatically,
retaining this criterion if there is no
action within 5 seconds or following
confirmation of the
"NO" function.
Follow the instructions.
If you wish to change the guidance
criterion, select the
"YES" function
then press the
"VAL" button.
Select a criterion from the list offered
then confirm (
"VAL" button). When
the criterion of your choice is selected,
select the
"Validate" function then
press the
"VAL" button. Guidance
begins, follow the instructions.
45
-
Audio equipment and telematics
01-01-2006
Selecting a service
The last address entered is
displayed.
There are 3 options for defining the
location in which you wish to obtain
a service:
- resume the last address entered by
means of the
"Validate" function.
- enter the name of a new town
then enter the street (or the
"City
centre" function) by means of the
"Change" function.
- automatically enter your current
location by using the
"Current
location" function.
After confirming the address, select
a service by scrolling through the list
using the direction arrows then press
the
"VAL" button.
A cursor on the left-hand side of the
screen indicates your position in the
list.
The address of the required service
is displayed.
An indication on the right-hand
side of the screen (e.g. 1/50)
indicates whether there are any
other establishments (50 maximum)
offering the same service within a
radius of approximately 30 miles
(50 km).
Use the
"Next" or "Previous"
functions to consult the list offered.
When the establishment of your
choice is displayed, select the
"Validate" function then press the
"VAL" button. Select a guidance
criterion. Guidance begins, follow the
instructions.
46 - Audio equipment and telematics
01-01-2006
Storing an address in a directory
When a new address is entered, you
can store it by selecting the
"Store"
function.
Enter the description of the address.
If the description already exists for
a different address, you can replace
the old address with a new one.
Select the Personal or Professional
directory, then press the
"VAL"
button. The address is then stored in
the directory of your choice (directory
capacity 100 addresses).
Selecting a stored destination
Using the direction arrows, select the
directory in which the address you
are looking for is stored then press
the
"VAL" button.
The stored addresses are displayed.
A cursor on the left-hand side of the
screen indicates your position in the
list. Select a description, by scrolling
through the list using the direction
arrows, then press the
"VAL" button.
The complete address is displayed.
Select the
"Validate" function then
press the
"VAL" button. Select a
guidance criterion. Guidance begins,
follow the instructions.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст