Peugeot Partner (2022 year). Manual in english — page 3
Access
Activation/Deactivation
Side-hinged doors
Opening to approximately 180°
2
You can activate or deactivate this function
Keeping the left-hand door closed with the
permanently.
right-hand door open
► With the ignition on, press the central locking
button until an audible signal is triggered and
a corresponding message of confirmation is
displayed.
The state of the system stays in the memory
when the ignition is switched off.
If fitted to your vehicle, a check strap system
Driving with the doors locked may render
allows the doors to be opened from about 90° to
access by the emergency services to the
interior difficult in an emergency.
It is possible to drive with the right-hand
about 180°.
door open, to enable the transportation
► Pull the yellow control when the door is open.
of long loads.
The check strap will engage again automatically
Carrying long or voluminous objects
The left-hand door is kept closed by the
on closing.
If you want to drive with the boot open,
distinctive "yellow" lock, positioned at the
you should press the central locking button
base of the door.
to lock the doors. Otherwise, every time the
General
This closed door must not be used to retain
speed of the vehicle exceeds 6 mph (10
loads.
recommendations for the
km/h), the locks will rebound and the alerts
Driving with the right-hand door open is a
mentioned above will appear.
sliding side doors
special dispensation. Please comply with the
Pressing the central locking button unlocks
the vehicle.
usual safety instructions on how to warn other
Doors must only be operated when the
Above 6 mph (10 km/h), this unlocking is
drivers.
vehicle is stationary.
temporary.
For your safety and that of your passengers,
as well as for correct operation of the doors,
you are strongly advised not to drive with a
door open.
Always check that it is safe to operate the
door and in particular, be sure not to leave
children or animals near the door controls
without supervision.
43
Access
The audible warning, the lighting of the "door
To hold the sliding side door in the open
On a steep slope
open" warning lamp and the message on the
position, open the door fully to engage
screen are there to remind you. Contact a
the latch (located at the bottom of the door).
PEUGEOT dealer or a qualified workshop if
you want to deactivate this warning.
Doors and door clearances
Lock the vehicle when you use an automatic
car wash.
Take care when opening doors while the vehicle
Before opening or closing and while
is on a slope facing uphill. The sloping terrain
moving doors, ensure that no person,
could cause the door to open more quickly than
animal or object is in the door frame or any
usual.
other position that would block the desired
On a steep slope, manually guide the side door
movement, inside or outside the vehicle.
to help it to close.
If this advice is not followed, injuries or
If the vehicle is on a slope facing downhill,
damage may occur if any part of a person or
the door may not stay open, instead closing
an object is trapped or caught.
suddenly, with a risk of injury. Always hold
When open, a door projects beyond the body.
the door to ensure that it does not close
Take care not to block the guide space
Allow adequate clearance when parking
unexpectedly.
on the floor so that the door can slide
alongside walls, lamp-posts, high pavements,
On a steep slope, the door's weight may
correctly.
etc.
cause it to move, opening or closing
For safety and functional reasons, do not
suddenly as a result.
drive with the sliding side door open.
Avoid leaving the vehicle unsupervised on a
steep slope with one or more doors open. If
this advice is not followed, injuries or damage
may occur if a person or an object is trapped
or caught.
To hold the sliding side door in the open
When open, a door never projects
Rear roof flap
position, open the door fully to engage
beyond the rear bumper.
the latch (located at the bottom of the door).
44
Access
This roof flap at the rear is compatible only with
Support bar
Alarm
2
side-hinged doors.
The vehicle is equipped with a support bar for
transporting long loads, after opening the rear
roof flap.
► Fold back the support bar by lifting the lever.
► Guide it to the door pillar.
► Support the long loads to be transported, lift
them and reposition the support bar with one
hand.
► Ensure that it is secured correctly by
To open the rear roof flap:
pressing the handle downwards past the point of
System which protects and provides a deterrent
- Lift the black paddle of the toggle.
resistance and lash the load securely.
against theft and break-ins.
- Relax the toggle by pressing on the rear roof
The side supports can be used as hooking
Self-protection function
flap (downwards) then release the hook.
points.
The system checks for any malfunction
- Lift the rear roof flap.
The rear bumper has been reinforced to
in its components.
- Move past the point of resistance to lock the
serve as a step when entering the
The alarm is triggered if the battery, button or
rear roof flap with the support props.
vehicle.
siren wiring is disconnected or damaged.
Never drive without the props in place.
For all work on the alarm system, contact a
Never fasten a load to the roof flap.
PEUGEOT dealer or a qualified workshop.
To close the rear roof flap:
- Check that the support bar is properly
Exterior perimeter
Never drive without the support bar in
secured.
The system checks whether the vehicle is
place.
- Lower the rear roof flap.
opened.
The rear doors will only lock when the support
- While pressing on the rear roof flap
The alarm is triggered if anyone tries to open
bar is installed.
(downwards), take the two spring rings and then
one of the doors or the bonnet.
When the roof flap is open, take care when
place the hook in its housing.
driving where height is restricted.
- Lower the black paddle to lock the rear roof
Volumetric
Never rest loads directly on the rear doors.
flap.
Comply with the usual indications for warning
(without partition)
Locking the rear roof flap holds it firmly against
other drivers.
the seal, ensuring watertight sealing with no
Only use the roof flap on short trips.
noise.
45
Access
When the vehicle is parked, the alarm
or
will not be triggered if the vehicle is
► Unlock the vehicle with the "Keyless Entry
knocked.
and Start" system.
The monitoring system is deactivated: the
The system checks for any variation in volume in
indicator lamp in the button goes off and the
Locking the vehicle with full
the passenger compartment.
direction indicators flash for about 2 seconds.
The alarm is triggered if anyone breaks a
alarm system
If the vehicle automatically locks itself
window, enters the passenger compartment or
again (as happens if a door or the boot is
moves inside the vehicle.
Activation
not opened within 30 seconds of unlocking),
► Switch off the ignition and exit the vehicle.
the monitoring system is also reactivated
► Lock the vehicle using the remote control or
(with partition)
automatically.
with the "Keyless Entry and Start" system.
The monitoring system is active: the red indicator
The system only checks for a variation in volume
lamp in the button flashes every second and
Locking the vehicle
inside the cab.
the direction indicators come on for about 2
The alarm is triggered if anyone breaks a
with exterior perimeter
seconds.
window or enters the vehicle’s cab.
monitoring only
It will not be triggered if someone enters the
Following an instruction to lock the
Deactivate the interior volumetric and anti-tilt
loading area.
vehicle, the exterior perimeter monitoring
monitoring to avoid the unwanted triggering of
is activated after 5 seconds and the interior
If your vehicle is fitted with an Additional
the alarm, in certain cases such as:
volumetric and anti-tilt monitoring after 45
heating/ventilation system, interior
- Slightly open window or sunroof.
seconds.
volumetric monitoring is not compatible with it.
- Washing the vehicle.
For more information on the Additional
- Changing a wheel.
heating/ventilation system, refer to the
If a door, the tailgate or the bonnet is not
- Towing the vehicle.
corresponding section.
closed properly, the vehicle is not locked
- Transport on a ship or ferry.
but the exterior perimeter monitoring will be
activated after 45 seconds at the same time
Deactivating the interior volumetric
Anti-tilt
as the interior volumetric and anti-tilt
and anti-tilt monitoring
The system checks for any change in the attitude
monitoring.
► Switch off the ignition and within 10 seconds
of the vehicle.
press the alarm button until its red indicator lamp
The alarm is triggered if the vehicle is lifted or
Deactivation
is on fixed.
moved.
► Get out of the vehicle.
► Press the remote control unlocking button.
46
Access
► Immediately lock the vehicle using the remote
informs you that the alarm was triggered during
remote control or unlock the vehicle using the
2
control or the "Keyless Entry and Start" system.
your absence. When the ignition is switched on,
"Keyless Entry and Start" system.
Only the exterior perimeter monitoring is
this flashing stops immediately.
activated; the button's red indicator lamp flashes
Electric windows
once every second.
Failure of the remote control
To deactivate the monitoring functions:
To be taken into account, the deactivation
Type 1
► Unlock the vehicle using the key in the front
must be carried out every time the
left-hand door lock.
ignition is switched off.
► Open the door; the alarm is triggered.
► Switch on the ignition; this stops the alarm.
Reactivating the interior volumetric
The indicator lamp in the button goes off.
and anti-tilt monitoring
Locking the vehicle without
► Deactivate the exterior perimeter monitoring
by unlocking the vehicle using the remote control
activating the alarm
1. Left-hand front.
or the "Keyless Entry and Start" system.
2. Right-hand front.
► Lock or deadlock the vehicle using the key
The indicator lamp in the button goes off.
(built-in the remote control) in the driver's door
► Reactivate all monitoring by locking the
lock.
Type 2
vehicle using the remote control or the "Keyless
Entry and Start" system.
Malfunction
The red indicator lamp in the button once again
When the ignition is switched on, the fixed
flashes every second.
lighting of the red indicator lamp in the button
indicates a system malfunction.
Triggering of the alarm
Have it checked by a PEUGEOT dealer or a
This is indicated by sounding of the siren
qualified workshop.
and flashing of the direction indicators for 30
seconds.
Automatic activation
Depending on the country of sale, certain
(Depending on version)
monitoring functions remain active until the alarm
The system is activated automatically 2 minutes
has been triggered eleven times consecutively.
after the last door or the boot is closed.
When the vehicle is unlocked using the remote
► To avoid triggering the alarm on entering the
control or the "Keyless Entry and Start" system,
vehicle, first press the unlocking button on the
rapid flashing of the indicator lamp in the button
47
Access
opens/closes completely when the switch is
The lamp will remain lit until the controls are
released.
reactivated.
Operating the switch again stops the movement
The rear electric windows can still be controlled
of the window.
using the driver's controls.
Window controls remain operational for
Reinitialising the electric
approximately 45 seconds after switching
off the ignition or after locking the vehicle.
windows
After that time, the controls are disabled.
After reconnecting the battery, or in the event
To reactivate them, switch on the ignition or
of abnormal window movement, the anti-pinch
unlock the vehicle.
function must be reinitialised.
The anti-pinch function is disabled during the
Anti-pinch
following sequence of operations.
(Depending on version)
For each window:
If the window meets an obstacle while rising, it
► Lower the window fully, then raise it; it will
stops and immediately partially lowers again.
rise in steps of a few centimetres each time the
1.
Left-hand front
control is pressed. Repeat the operation until the
2.
Right-hand front
Deactivating the rear
window is fully closed.
3.
Right-hand rear (depending on version)
► Continue to pull the control for at least one
4.
Left-hand rear (depending on version)
controls for the rear electric
second after the window reaches the closed
5.
Deactivation of electric window controls
windows
position.
located by rear seats (depending on version)
(Type 2)
If an electric window meets an obstacle
during operation, the movement of the
Manual operation
window must be reversed. To do this, press
► To open/close the window, press/pull the
the relevant control.
switch without passing the point of resistance;
When the driver operates the passengers’
the window stops as soon as the switch is
electric window controls, it is important to
released.
For your children's safety, press control 5 to
ensure that nothing can prevent the window
deactivate the controls for the rear electric
from closing properly.
Automatic operation
windows, irrespective of their positions.
It is important to ensure that passengers use
(Depending on version)
The red indicator lamp in the button comes
the electric windows correctly.
► To open/close the window, press/pull the
on and a confirmation message is displayed.
Pay particular attention to children when
switch past its resistance point: the window
operating the windows.
48
Access
Be aware of passengers and/or other persons
2
present when closing windows remotely using
the electronic key.
Do not put your head or arms through the
open windows when the vehicle is moving -
risk of serious injury!
Tilting rear door windows
Opening
► Turn the lever outwards.
► Push it fully to secure the window in the open
position.
Closing
► Pull the lever to release the window.
► Turn the lever fully inwards to secure the
window in the closed position.
49
Ease of use and comfort
- In row 3, be careful not to leave your feet
General
Front seats
under the row 2 seat while it is being tilted.
recommendations for the
- When a row 3 seat is in the fully folded
PEUGEOT i-Cockpit
position, ensure that the strap is correctly
seats
hooked to the Top Tether fixing of the row 2
For safety reasons, seat adjustments
backrest: risk of unexpected tipping of the
must only be made when the vehicle is
seat.
stationary.
Before carrying out the manoeuvres,
Folding or unfolding the seat backrests
check that nothing and no one is
must only be done with the vehicle
obstructing the moving elements and their
stationary.
locking.
To avoid sudden folding, take care to hold the
backrest and support it until it is horizontal.
Before moving the seat backwards,
Never put your hand underneath the seat
ensure that there is no person or object
cushion to guide the seat downwards or
Before taking to the road and to make the
that might prevent the full travel of the seat.
upwards, you could get your fingers trapped.
most of the ergonomic layout of the PEUGEOT
There is a risk of trapping or pinching
Place your hand on the grip/strap (depending
i-Cockpit, carry out these adjustments in the
passengers if present in the rear seats or of
on equipment) at the top of the seat cushion.
following order:
jamming the seat if large objects are placed
- head restraint height.
on the floor behind the seat.
- seat backrest angle.
Please note: an incorrectly latched
- seat cushion height.
backrest compromises the safety of
Do not place hard or heavy objects on
- longitudinal seat position.
passengers in the event of sudden braking or
the backrests forming a table. They could
- steering wheel reach and then height.
an impact.
become dangerous projectiles in the event of
- rear view mirror and door mirrors.
The contents of the boot may be thrown
sudden braking or a collision.
forward - risk of severe injury!
Once these adjustments have been
- Do not remove a head restraint without
stowing it; secure it to a support inside the
made, check that the "head-up"
vehicle.
instrument panel can be viewed correctly over
- Check that the seat belts remain accessible
the smaller diameter steering wheel.
to the passenger and easy to fasten.
- Passengers must never take their seat
without adjusting and fastening their seat belt.
50
Ease of use and comfort
Adjustments
Tilting the backrest
3
Longitudinal
► Push the control backwards then use your
weight and your legs to adjust the backrest.
Lumbar
(driver only)
► To put the armrest in the vertical position,
raise it until it locks into place.
► Lower the armrest to return it to the position
for use.
► Raise the control and slide the seat forwards
The armrest can be removed from the passenger
or backwards.
seat.
Removing the armrest
Height
► Raise the armrest into the vertical position.
► Turn the knob to obtain the desired level of
(driver only)
lumbar support.
Armrest
► Push the armrest shaft towards the backrest.
► If fitted to the vehicle, pull the control
► While holding it in this position, rotate the
upwards to raise or push it downwards to lower,
armrest towards the rear.
as many times as necessary to obtain the
► Pull the armrest to detach it from the
position required.
backrest.
Refitting the armrest
For more information on the Seat belts,
refer to the corresponding section.
51
Ease of use and comfort
Retractable position
► Approximately 30 seconds after starting the
► Slot the armrest into the backrest, ensuring
engine, press the control.
that you align the bayonet lugs with the holes.
It can be activated when the outside temperature
► Push the armrest shaft towards the backrest.
is below 20°C.
► While holding it in this position, rotate the
► If the centre console inconveniences you,
The temperature is controlled automatically.
armrest towards the front. The armrest is once
remove the passenger's seat armrest.
Pressing again interrupts operation.
again secured onto the backrest.
► Push the control rearwards fully to tilt and
guide the assembly.
If you press the control while the engine
Storage compartment under
This position allows you to transport long loads
is not running, the request will be
inside the vehicle with the doors closed.
memorised for approximately 2 minutes.
the seat
When retracted, the maximum permitted weight
on the backrest is 50 kg.
► To reposition the seat cushion, raise the
backrest until it locks in the raised position.
With the two-seat front bench seat, the driver's
seat control switches the heating on or off for the
Heated seat control
bench seat’s outer seat.
Do not use the function when the seat
is not occupied.
Reduce the heating intensity as soon as
possible.
► Lift the passenger’s seat cushion to access
When the seat and passenger compartment
the storage compartment.
have reached a satisfactory temperature,
52
Ease of use and comfort
switch the function off; reducing electrical
► Adjust the height and reach.
► Return control A or C (depending on the
3
consumption in turn decreases energy
► Lower the control lever to lock the steering
version you have) to its centre position.
consumption.
wheel.
As a safety measure, the mirrors should
As a safety precaution, these operations
be adjusted to reduce the blind spots.
Prolonged use of heated seats is not
must only be carried out while the vehicle
The objects observed are, in reality, closer
recommended for people with sensitive
is stationary.
than they appear.
skin.
Take this into account when assessing the
There is a risk of burns for people whose
distance of vehicles approaching from behind.
perception of heat is impaired (e.g. illness,
Mirrors
taking medication).
To keep the heated pad intact and to prevent
Manual folding
a short circuit:
Door mirrors
You can manually fold the mirrors (parking
- Do not place heavy or sharp objects on the
obstruction, narrow garage, etc.)
seat.
Adjustment
► Turn the mirror towards the vehicle.
- Do not kneel or stand on the seat.
- Do not spill liquids onto the seat.
Electric folding
- Never use the heating function if the seat
Depending on equipment, the door mirrors can
is damp.
be folded electrically.
► From the inside, with the
ignition on, place control A in the
Steering wheel
central position.
► Pull control A backwards.
adjustment
► Lock the vehicle from the outside.
If the mirrors are folded using control A,
► Move control A or turn control C (depending
they will not unfold when the vehicle is
on the version you have) to the right or to the left
unlocked.
to select the corresponding mirror.
► Move control B or C (depending on the
Electric unfolding
version you have) in any of the four directions to
► When stationary, pull the control lever to
adjust.
The door mirrors are unfolded electrically when
the vehicle is unlocked using the remote control
release the steering wheel.
53
Ease of use and comfort
or key. Unless folding was selected with control
Manual model
Child-monitoring mirror
A, pull the control in the central position towards
Day/night position
the rear again.
Folding/unfolding when locking/unlocking
the vehicle can be deactivated. Contact a
PEUGEOT dealer or a qualified workshop.
If necessary, the mirrors can be folded
manually.
► Pull the lever to change to the anti-dazzle
Heated mirrors
"night" position.
► Push the lever to change to the normal "day"
position.
A child-monitoring mirror is installed above
Adjustment
the interior rear view mirror. It allows the
► Adjust the mirror to the normal "day" position.
vehicle's rear passengers to be observed and
facilitates discussion between the front and rear
Automatic "electrochrome" model
passengers without changing the mirror setting
The electrochrome system uses a sensor that
and without turning around. It can be folded
detects the level of exterior brightness and that
easily to avoid dazzle.
► Press one of these buttons.
coming from the rear of the vehicle, in order to
automatically and gradually switch between day
For more information on Rear screen
2-seat front bench seat
and night usage.
demisting/de-icing, refer to the
corresponding section.
To ensure optimum visibility while
manoeuvring, the mirror automatically
brightens when reverse gear is engaged.
Interior rear view mirror
The system is deactivated if the load in the
Equipped with an anti-dazzle system, which
boot exceeds the height of the load space
darkens the mirror glass and reduces the
cover or if the load space cover has items
nuisance to the driver caused by the sun,
placed on it.
headlamps of other vehicles, etc.
54
Ease of use and comfort
Central seat
Storage compartment under seats
3
Table position
The vehicle may also be fitted with a pivoting
table.
► To return the backrest to the sitting position,
stow the table, then guide it until it locks.
► Lift the central seat to access the storage
► To lower the backrest, pull the tab on the
Take care not to jam the tab under the seat
compartment. This space can be secured by
lower edge of the seat.
cushion while moving the backrest.
fitting a padlock (not supplied).
Each time you lock the seat in the sitting
position, make sure that passengers
have access to the seat belt end pieces and
the associated straps.
Never use the table while the vehicle is
being driven.
In the event of sudden braking or impact, any
objects on the table might become dangerous
The backrest of the central seat of the bench
projectiles that could cause injury.
seat tilts to form a work table, creating a mobile
office (for use while stationary).
55
Ease of use and comfort
Side seat
Folded position
Rear bench seat (row 2)
Retractable position
For safety reasons, seat adjustments
must only be made when the vehicle is
stationary.
Folding the backrests
First steps:
► lower the head restraints,
► if necessary, move the front seats forward,
► check that nothing or no person might
interfere with the folding of the backrests
► Lift the yellow crank at the base of the seat to
(clothing, luggage, etc.),
► Pull the tongue on the top edge of the seat
unlock and lift the assembly into folded position
► check that the outer seat belts are lying flat
near the head restraint to tilt and guide the
(seat raised against the backrest) until it locks.
on the backrests.
assembly.
This position allows the transport of high loads
It is placed in the floor of the front seat and thus
inside the cab.
The folding of the backrest is
forms a continuous flat floor with the loading
To replace the seat, push on the yellow crank
accompanied by a slight lowering of the
space.
under the seat and lower the assembly until the
corresponding seat cushion.
This position allows transporting long cargo
seat locks into position on the floor.
When the backrest is released, the red
inside the vehicle with the doors closed.
indicator is visible in the release grips on the
Never put your hand underneath the seat
When retracted, the maximum weight on the
outer seats.
cushion to guide the seat downwards or
backrest is 50 kg.
upwards, you could get your fingers trapped.
To replace the seat, lift the backrest until the seat
Place your hand on the front of the seat
locks into position on the floor.
cushion.
Never put your hand underneath the seat
Before carrying out these manipulations,
cushion to guide the seat downwards or
check that nothing and nobody is obstructing
upwards, you could get your fingers trapped.
the moving elements and their locking.
Always just use the strap.
Before carrying out these manoeuvres, check
that nothing and nobody is obstructing the
► Turn the backrest release handle 1.
moving elements and their locking.
56
Ease of use and comfort
► Guide the backrest down to the horizontal
The folding of the backrest is
► Guide the backrest down to the horizontal
3
position.
accompanied by a slight lowering of the
position.
corresponding seat cushion.
With the central seat, only the strap must
Repositioning the backrests
When the backrest is released, the red
be used.
indicator is visible in the release grips on the
First check that the outer seat belts are
outer seats.
lying vertically flat alongside the backrest
Repositioning the backrests
latching rings.
Outer seat (left-hand or right-hand)
Outer seat (left-hand or right-hand)
► Put the backrest in the upright position and
First check that the outer seat belts are
push it firmly to latch it home.
lying vertically flat alongside the backrest
► Check that the red indicator in the release
latching rings.
grip 1 is no longer visible.
► Ensure that the outer seat belts are not
► Put the backrest in the upright position and
trapped during the manoeuvre.
push it firmly to latch it home.
► Check that the red indicator on the release
grips 1 of the outer seats is no longer visible.
Rear seats (row 2)
► Ensure that the outer seat belts are not
► Turn the backrest release handle 1.
trapped during the manoeuvre.
► Guide the backrest down to the horizontal
position.
Check that the backrest of the upright
Central seat
central seat is correctly aligned with the
Folding the backrests
backrests of the outer seats.
First steps:
► lower the head restraints,
Central seat
► if necessary, move the front seats forward,
► Put the backrest in the upright position and
► check that nothing or no person might
push it firmly to latch it home.
interfere with the folding of the backrests
► Check that the central seat belt is not trapped
(clothing, luggage, etc.),
during the manoeuvre.
► check that the outer seat belts are lying flat
on the backrests.
Rear seats (row 3)
► Pull the backrest release tab 1.
57
Ease of use and comfort
Access to row 3
► Lower the head restraint as far as it will go.
If you want to load luggage onto the row 3
backrests while in the table position, the row 2
► Operate control 1 to fold the backrest onto
seats must also be folded down.
► Using the row 2 seat grip, fold the backrest.
the seat cushion.
► To reposition it, tilt the backrest backwards
Repositioning the backrest
Longitudinal adjustment
until it locks into place.
► Unlock it by pulling control 1.
Long
► Return it to its initial position
Labels in row 3
► Check that the assembly is anchored
properly.
Fully folded position
Long
Placing the seat in the fully folded position
► Place the backrest in the table position.
While driving, it is prohibited to have a
passenger seated next to a seat in the fully
► Raise the control and slide the seat forwards
folded position.
or backwards.
Table position
Placing the backrest in the table position
58
Ease of use and comfort
► Lower the head restraint as far as it will go.
Head restraint height
3
► Place the seat in the fully folded position.
adjustment
► Pull on the strap 3 to open the seat
anchorages.
► While still holding the strap 3, lift the seat.
► To raise it, pull it upwards as far as possible
Refitting the seat
(notch).
► Pull on the strap 3 to open the seat
► To remove it, press the lug A and pull it
anchorages.
upwards.
► While still holding the strap 3, place them in
► To put it back in place, engage the head
the anchorage points on the floor.
restraint rods in the openings keeping them in
► Release the strap 3.
line with the seat backrest.
► Lift the bar 2, located behind the seat, to
► Ensure that no object or feet are obstructing
► To lower it, press the lug A and push down on
release the feet of the seat from their anchorage
the rear anchorage points 4 and that the seat
the head restraint at the same time.
in the floor.
belt is correctly positioned and available.
► Tilt the entire seat forwards.
The head restraint has a frame with
► Fold the seat backwards to fix its rear
► Hook the strap 3 on the row 2 head restraint
notches which prevents it from lowering;
anchorage feet.
rod.
this is a safety device in case of impact.
► Use the control 1 to lift the backrest to its
Returning the seat to the sitting position
The adjustment is correct when the upper
original position.
► Fold the entire seat backwards.
edge of the head restraint is level with the
► Raise the head restraint.
► Check that the seat belt is not trapped during
top of the head.
the manoeuvre.
Never drive with the head restraints removed;
Removing the seat
they must be fitted and correctly adjusted.
59
Ease of use and comfort
Never drive with passengers seated at
Removing/refitting
the rear when the head restraints are
► To remove it on the driver's side, move
removed or not in the high position; the head
the seat as far back as possible and give the
restraints must be in place and in the high
fasteners a quarter turn.
position.
For more information on the Seat belts,
This compartment, located above the sun visors,
refer to the corresponding section.
can be used to store various objects.
► To refit it, position the mat and replace the
Roof and roof storage
Interior fittings
fasteners, giving them a quarter turn.
► Check that the mat is secured correctly.
Mats
To avoid any risk of jamming the pedals:
- Only use mats which are suited to the
Overhead storage compartment and
Fitting
fixings already present in the vehicle; these
central storage compartment
fixings must be used.
- Never fit one mat on top of another.
The use of mats not approved by PEUGEOT
may interfere with access to the pedals and
hinder the operation of the cruise control/
speed limiter.
The approved mats have two fasteners
located underneath the seat.
The overhead storage compartment (1) is
Overhead storage unit
located above the sun visors and can be used to
store miscellaneous objects.
When fitting it on the driver's side, only use the
There is a storage space (2) located in the roof
mountings present on the carpet.
lining.
The other mats are simply laid over the carpet.
The maximum permitted load is 6 kg.
60
Ease of use and comfort
In the event of sharp deceleration,
Open the rear storage compartment with
12 V accessory socket(s)
3
objects placed in the central storage
care, to prevent any objects stored inside
compartment of the roof may be transformed
from falling out.
into projectiles.
Light ambience
Rear storage compartment
The light ambience settings are
This compartment is accessible from the rear
changed via
seats and from the vehicle's boot.
the Driving/Vehicle touch screen menu.
It has a capacity of 60 litres and the maximum
Blind
permitted load is 10 kg.
Opening/Closing
► Plug in a 12 V accessory (with a maximum
rated power of 120 W) using a suitable adapter.
Observe the maximum power rating to
avoid damaging the accessory.
The connection of an electrical device
► To open it from the rear seats, slide the rear
► Press and hold the button; the blind opens/
not approved by PEUGEOT, such as a
storage compartment shutters.
closes, stopping when the button is released.
USB charger, may adversely affect the
operation of vehicle electrical systems,
If the blind becomes trapped while
causing faults such as poor radio reception or
moving, reverse its movement. To do
interference with displays in the screens.
this, press the relevant control.
When pressing the button to open/close the
blind, the driver must ensure that nothing and
no one might interfere with its movement.
The driver must ensure that passengers use
the blind correctly.
Pay particular attention to children when
► To open it from the vehicle’s boot, place your
operating the blind.
thumb on the boot recess then pull the handle.
61
Ease of use and comfort
USB socket(s)
Socket 1 allows a
► Connect your multimedia or other electrical
smartphone to be
device (telephone charger, laptop computer,
connected by Android Auto® or CarPlay®,
CD-DVD player, bottle warmer, etc.).
enabling certain smartphone applications to be
In the event of a malfunction, the
used on the touch screen.
green indicator lamp flashes.
Sockets 1 and 2* allow a portable device to be
Have the socket checked by a PEUGEOT dealer
connected in order to charge it.
or a qualified workshop.
For best results, use a cable made or approved
Connect only one device at a time to the
by the device manufacturer.
socket (do not use extension leads or
These applications can be managed using the
multi-socket adapters).
steering-mounted controls or the audio system
Connect only devices with class II insulation
controls.
(shown on the device).
Do not use metal-cased devices (e.g. electric
220 V/50 Hz socket
shaver, etc.).
As a safety measure, if power
consumption is high and power is
Socket 1 enables audio files sent to your audio
AC 220V
required by the vehicle's electrical system
50Hz
120W
(due to severe weather conditions, electrical
system to be played through the vehicle's
speakers.
overload, etc.), power to the socket may be
cut off, in which case the green indicator lamp
When the USB socket is used, the
goes off.
portable device charges automatically.
It is located on the side of the central storage
While charging, a message is displayed if the
compartment.
power drawn by the portable device exceeds
Wireless smartphone
This socket (max. power: 150 W) operates with
the current supplied by the vehicle.
the engine running, and with the Stop & Start
charger
For more information about how to use this
system in STOP mode.
equipment, refer to the sections describing
► Lift the protective cover.
the audio and telematics systems.
► Check that the green indicator lamp is on.
* Only on the Peugeot Partner.
62
Ease of use and comfort
The system is not designed to charge
State of the
Meaning
3
multiple devices simultaneously.
indicator lamp
Do not leave metal objects (e.g. coins,
Flashing orange
Foreign object detected in
keys, vehicle remote control) in the
the charging zone.
This system allows wireless charging of a
charging area while a device is being charged
Portable device not well
portable device such as a smartphone, using the
- Risk of overheating or interrupting the
centred in the charging
magnetic induction principle, in accordance with
charging!
zone.
the Qi 1.1 standard.
The portable device to be charged must be
Fixed orange
Malfunction of the
compatible with the Qi standard, either by design
portable device's battery
or by using a compatible holder or shell.
meter.
A mat can also be used provided that it is
Device battery
approved by the Manufacturer.
When using applications for a long time
temperature too high.
The charging area is identified by the Qi symbol.
in combination with wireless charging,
Charger malfunction.
The charger works with the engine running and
some smartphones may switch to thermal
with the Stop & Start system in STOP mode.
safety and cause some functions to stop.
Charging is managed by the smartphone.
If the indicator lamp is fixed orange:
With the Keyless Entry and Start system, the
- remove the device, then place it back in the
Checking operation
charger’s operation may be briefly disrupted
centre of the charging zone.
when a door is opened or the ignition is switched
The state of the indicator lamp allows the
or
off.
operation of the charger to be monitored.
- remove the device and try again in a quarter
of an hour.
State of the
Meaning
Charging
If the problem persists, have the system checked
indicator lamp
► With the charging area clear, place a device
by a PEUGEOT dealer or a qualified workshop.
Off
Engine switched off.
in its centre.
No compatible devices
Floor boxes (Petrol or
detected.
Diesel)
When the portable device is detected, the
Charging complete.
charger’s indicator lamp lights up green. It
Fixed green
Compatible portable
remains lit for the whole time that the battery is
device detected.
being charged.
Charging.
63
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст