Peugeot Partner (2022 year). Manual in english — page 4

Ease of use and comfort

Do not place hard or heavy objects on

High load retaining net

the table. Such objects could become

projectiles in the event of sudden

deceleration.

Side blinds

There are two boxes located under the rear

passenger footwells.

They are fitted to the windows of the sliding side

► To open them, slide your fingers into the

doors (depending on version).

notch and lift the cover.

Aircraft style tables

This net, hooked onto the upper mountings and

the lower rings or lugs, enables the use of the full

loading volume, up to the roof:

- Behind the front seats (row 1) when the rear

seats are folded.

- Behind the rear seats (row 2).

When positioning the net, check that the

► To raise or lower the blind, pull it by the tab.

strap loops are visible from the boot; this

will make slackening or tightening them

To avoid damaging the blind:

easier.

- Guide it slowly, using the tab, while

raising or lowering it.

- Make sure the tab is securely fastened

Remove the luggage cover shelf or roller

► To put the table back in place, pull it upwards.

before opening the door.

(depending on version).

As a safety precaution, the aircraft style table

unhooks itself if excessive pressure is applied.

► To store the table, pull it downwards.

Ease of use and comfort

Installation behind row 1

spring hook to the ring on the corresponding

Never use the ISOFIX ring, which is for

strap.

fixing the strap of a child seat with Top

► Fold down the rear seats.

Tether.

► Tighten the straps without raising the bench

seat.

Two-position luggage cover

► Check that the net is hooked and tightened

correctly.

shelf (removable)

Installation behind row 2

Standard

► Open the covers on the upper mountings 1.

► Unroll the high load retaining net.

► Position one end of the net's metal bar in the

corresponding upper mounting 1, then do the

same with the other end.

► Fully extend the straps.

► Fold or remove the luggage cover.

► Open the covers on the upper mountings 2.

► Unroll the high load retaining net.

► Position one end of the net's metal bar in the

corresponding upper mounting 2, then do the

same with the other end.

► Attach the hook on each of the net's straps

to the corresponding stowing ring 4 (located on

It can be installed in two different positions: high

the floor).

and low.

► Tighten the straps.

It consists of two sections which can be folded

► Wind each strap around bar 3 located under

► Check that the net is hooked and tightened

back on each other.

the front seat cushion (row 1), then secure each

correctly.

► To fold it from the boot, grasp it and fold it

back on itself up to the rear seats. From the

Ease of use and comfort

low position, you can store it folded by sliding it

Installation

towards the backrests of the rear seats.

► To deploy it from the boot, grasp it and unfold

it to the boot pillars.

The maximum authorised weight on the

luggage cover shelf is 25 kg.

Luggage cover

► The roller can be stored behind row 2 or 3.

Long

Removal

► Remove the roller guides from the rails in

Long

pillars B.

► Position the left and right ends of the roller in

the cut-outs A.

► Guide the roller as it reels in.

In the 5-seat configuration, it is installed behind

► Unlock the roller by pressing one of the

► Pull out the roller until it reaches the boot

the second row seats, with the third row seats

handles located at the ends of the roller bracket.

pillars.

stored folded away.

► Insert the roller guides into the rails in the

In the 7-seat configuration, it is stored behind the

Load retaining partition

pillars B.

third row seats.

In the event of sudden deceleration,

objects placed on the load space cover

can turn into projectiles.

► Depending on version, you can access the

boot by opening the rear screen in the tailgate

and attaching the roller guides into the rails in

the pillars C.

Ease of use and comfort

On the floor, behind the front seats, a vertical

Storage compartment

partition protects the driver and front passengers

against the risk of load movement.

Steel or glazed partitions separate the loading

area from the cab.

When washing your vehicle, never clean

the inside directly using a water jet.

Stowing rings

Use the stowing rings on the rear floor to secure

loads.

As a safety precaution in case of sharp braking,

There is a compartment in the interior trim of the

we recommend placing heavy objects as far

boot in which to store a warning triangle.

forwards as possible (i.e. near the cab).

We recommend using the stowing rings on the

Recommendations on

floor to firmly secure the load.

loading

When washing your vehicle, never clean

the inside directly using a water jet.

Warning triangle

The weight of the load must comply with

the Gross Train Weight (GTW).

For more information on Engine technical

data and towed loads, refer to the

As a safety precaution, before leaving your

corresponding section.

vehicle to set up and install the triangle, always

switch on the hazard warning lamps and put on

If you are using a carrying system (roof

your high visibility vest.

bars/roof rack), comply with the

maximum loads associated with this system.

For more information on Roof bars/Roof

rack, refer to the corresponding section.

Ease of use and comfort

Make sure that the size, shape and

To prevent the load from sliding, there must

volume of the loads carried are

not be any empty spaces between the load

compatible with the highway code and safety

items and the vehicle wall panels.

regulations and do not impair the driver’s field

As well as the straps, optimise the stability

Avoid anchoring loads or hanging items

of vision.

of the load with stable handling equipment

on the wall of the partition.

(wedges, rigid blocks of wood or padding).

For safety reasons, ensure that small objects

The load must be evenly distributed in

do not slip through the gaps of about 3 cm

the loading area so as not to interfere

When washing the vehicle, never clean

between the partition and the vehicle's

with driving the vehicle.

the interior directly with a water jet.

bodywork.

Place the load close to the side wall panels,

or push it against the side wall panels

For the Multi-Flex bench

between the wheel arches.

Multi-Flex bench seat

However, it is recommended that heavy

seat and the Crew cab

objects are placed as close to the cab as

Do not place sharp or pointed objects in

possible as a precaution in case of sharp

the protective cover to avoid damaging it.

braking.

This assembly comprises the two-seat front

bench seat and a removable flap.

Firmly secure all parts of the load using

For more information on the two-seat front

the stowing rings on the floor of the

bench seat, refer to the corresponding section.

loading area.

A partition located on the floor behind the front

For more information on the Interior fittings

seats protects the driver and front passengers

and in particular on the stowing rings, refer to

against the risk of load movement.

Do not place objects on the

the corresponding section.

A movable flap in this partition can be removed

dashboard.

to allow long items to be loaded.

Deactivate the front passenger airbag when

To avoid the risk of injury or accident, the

A protective cover is supplied with the vehicle to

carrying long objects.

load must be made stable so that it

enable long items to be carried safely.

For more information on Deactivating

cannot slide, tip over, fall or be projected. To

the front passenger airbag, refer to the

do this, use only retaining straps that conform

corresponding section.

to current standards (DIN, for example).

For more information on putting straps in

Avoid placing short or heavy loads in the

place, refer to the manufacturer’s user guide.

protective cover; use the loading area

whenever possible.

Ease of use and comfort

Removing the flap

► Tilt the flap, with the yellow hinges pointing

► Fold down the outer passenger seat backrest.

downwards.

► Insert the hinges into their housing then press

down fully (to avoid vibrations).

► With one hand lift the flap to close it, then

with the other hand turn the control at the top of

the flap to secure it.

Positioning the protective

cover

Whenever the backrest of the outer seat

is folded down and the partition flap is

► Install the protective cover by fastening its

► While holding the flap with one hand, turn the

open, the protective cover must be installed.

4 snap hooks to the 4 anchor points on the

control at the top of the flap with the other hand

partition.

to release it.

► Pull out the head restraint rods from the

► Lower the flap to remove it from its housing.

folded backrest, leaving two notches visible.

► Stow it behind the driver’s seat, turning the

► Load the desired objects.

control at the top of the flap to secure it.

No passengers must be allowed to sit in

The maximum load permitted on the

Refitting the flap

folded backrest is 100 kg.

the central seat if the backrest of the

right-hand outer seat is lowered and the

partition flap is open.

When loading long objects, take care to

► Place the strap of the cover around the head

install the protective cover correctly.

restraint.

Read the following procedure carefully.

Ease of use and comfort

► Tighten the strap using the adjustable section

Stay alert if the vehicle is on a steep

in order to correctly retain the items that have

slope, with loads behind the partition and

been loaded inside the cover.

passengers on board!

The protective cover may be left in place

after use.

Regularly check the condition of the

protective cover.

When signs of wear and tear appear, contact

a PEUGEOT dealer to have it replaced by a

protective cover that meets the specifications

and qualities required by PEUGEOT and your

vehicle.

Do not place loads behind the partition

positioned behind row 2, if the backrest

Crew cab

A movable partition that can be placed behind

of part 2/3 of the bench seat is folded down.

the first or second row of seats protects the

driver and passengers against the risk of load

movement.

A hatch in the partition can be opened to allow

long items to be carried.

A protective cover is supplied with the vehicle to

enable long items to be carried safely.

Deactivate the front passenger airbag

Lock the movable partition in these 2

when carrying long objects.

positions only.

Do not lean on the movable partition

when boarding!

Ease of use and comfort

Moving the partition

The upper stops may be adjusted if:

Opening/closing the hatch

- excessive force is needed to operate

Moving the partition forwards

the upper latches A and B.

- there is noise while driving, caused by

excessive play.

When the partition is locked behind the

row 2 or row 1 seats, an engagement

noise tells you that the upper and lower

latches are closed.

Never drive with the partition unlocked.

► Open/close the hatch E using the latch.

► Use the stay F to keep it in the open position.

► Fold the backrests of the row 2 seats and

The partition must not be moved with the

check that they are properly folded. If necessary,

When carrying a long load, the hatch E

latches extended - risk of scratches or

adjust the position of the row 1 seats (moving

must be kept in the open position with

damage to the plastic trims!

them forwards).

the stay F.

► Release the upper latches A and B.

The partition must never be removed to

► Check that the latches C and D are retracted.

Systematically close the hatch E, store

convert the vehicle from a commercial

► Slide the partition forwards.

the stay F in its housing (using the clip)

vehicle to a passenger vehicle.

► Lock the lower latches C and D and then

and straighten the backrest of the side

This would pose a risk to the safety of users

check that the locating pins are correctly

passenger seat(s) (depending on the position

due to the absence of a child lock on the

engaged in their housings.

of the partition) when no long load is being

tailgate (mandatory on passenger vehicles).

► Lock the upper latches A and B.

transported.

Moving the partition backwards

Pay attention to the loading height

► Release the upper latches A and B.

Avoid placing loads on the sill bar of the

behind the partition and the size of the

► Release the lower latches C and D.

hatch E. Whenever possible, place loads

long load in the protective cover: the driver

► Slide the partition backwards.

on the folded-down seat backrests.

must keep a good field of vision.

► Lock the upper latches only A and B.

The maximum load on the sill of the hatch E

► Return the backrests of the row 2 seats to

is 20 kg.

Do not place loads between the partition

their positions.

and the bench seat backrest.

Ease of use and comfort

Positioning the protective

lowered and the hatch is open with a long

load.

cover

In row 2, no passengers must be allowed to

sit in the central seat if the backrest of the

outer seat is lowered and the hatch is open

with a long load.

When loading long objects, take care to

► Install the protective cover by fastening its

install the protective cover correctly.

4 snap hooks to the 4 anchor points on the

partition.

► Fold the backrest of the outer passenger

► Pull out the head restraint rods from

seat(s) (depending on the position of the

the folded backrest(s) of the outer seat(s)

The protective cover must be installed

partition).

(depending on the position of the partition),

whenever the backrest of the outer seat

For more information on the Rear bench seat,

leaving 2 notches visible.

is folded down and the partition hatch is open.

and especially on folding the backrests, refer to

► Load the desired objects.

the corresponding section.

For more information on the Two-seat front

Avoid placing heavy loads on the

bench seat, and especially the retracted position

folded-down backrest of row 1.

of the outer seat, refer to the corresponding

Whenever possible, place heavy loads on the

section.

floor.

The maximum load permitted on each of the

folded backrests of row 2 is 80 kg.

It is normal for surplus protective cover to

be visible when the partition is positioned

behind row 1.

In row 1, no passengers must be allowed

► Tidy this surplus protective cover in the

to sit in the outer seat if the backrest of

space under the glove box.

the outer seat located behind them in row 2 is

Ease of use and comfort

If the interior temperature is very high

Heating and Ventilation

after the vehicle has stood for a long

time in the sunshine, air the passenger

Advice

compartment for a few moments.

Put the air flow control at a setting high

Using the ventilation and air

enough to quickly change the air in the

conditioning system

passenger compartment.

► To ensure that air is distributed evenly,

keep the external air intake grilles at the base

of the windscreen, the nozzles, the vents, the

Condensation created by the air

air outlets and the air extractor in the boot

conditioning results in a discharge of

free from obstructions.

water underneath the vehicle. This is perfectly

► Do not cover the sunshine sensor located

normal.

on the dashboard; this sensor is used to

regulate the automatic air conditioning

Servicing the ventilation and air

► Position the strap(s) around the head

system.

conditioning system

restraint(s) (depending on the position of the

► Operate the air conditioning system for at

► Ensure that the passenger compartment

partition).

least 5 to 10 minutes once or twice a month to

filter is in good condition and have the filter

► Tighten the strap(s) using the adjustable

keep it in good working order.

elements replaced regularly.

section in order to correctly retain the items that

► If the system does not produce cold air,

We recommend using a composite passenger

have been loaded inside the cover.

switch it off and contact a PEUGEOT dealer

compartment filter. Its specific active additive

Do not place any load in the passenger

or a qualified workshop.

helps protect against polluting gases and bad

compartment outside the protective cover

When towing a large load on a steep gradient

smells.

(especially over the cover).

in high temperatures, switching off the air

► To ensure correct operation of the

conditioning increases the available engine

air conditioning system, have it checked

power, enhancing the towing capacity.

according to the recommendations in the

Regularly check the condition of the

Manufacturer’s service schedule.

protective cover.

When signs of wear and tear appear, contact

Avoid driving for too long with the

a PEUGEOT dealer to have it replaced by a

ventilation off or with prolonged operation

protective cover that meets the specifications

of interior air recirculation. Risk of misting and

and qualities required by PEUGEOT and your

deterioration of the air quality!

vehicle.

Ease of use and comfort

Rapid heating of the passenger

For more information on the Stop &

The maximum level of ventilation is to be

compartment

Start system, refer to the corresponding

reserved for defrosting or to cool the

section.

temperature in the vehicle if it is too high.

If the air flow control knob is set to the

Heating

minimum position (system deactivated),

► Press button 3c.

the temperature in the vehicle will no longer

► Set knob 1 to a high temperature

be controlled. A slight flow of air can still be

(minimum 21).

felt, due to the forward movement of the

► Set knob 2 to at least position 3. In cold

vehicle.

weather (around 0°C), the heating of the

passenger compartment is optimal when

Temperature

ventilation is at level 5.

Manual air conditioning

► Press button 4 to produce quicker results

► Turn the thumbwheel 1 from "LO" (cold)

The air conditioning system only operates with

(do not leave air recirculation active for too

to "HI" (hot) to adjust the temperature to your

the engine running.

long: risk of misting the windows).

requirements.

► Do not press any of the other buttons.

A setting of around 21 provides optimum

comfort. Depending on your

requirements, a setting between 18 and 24 is

normal.

Contains R134A fluorinated

In addition, we recommend avoiding left/right

1. Temperature.

greenhouse gases

setting differences of more than 3.

2. Air flow.

Depending on version and country of sale, the

3. Air distribution.

air conditioning system may contain R134A

On entering the vehicle, if the interior

4. Interior air recirculation.

fluorinated greenhouse gases.

temperature is significantly colder or

5. Air conditioning on/off.

warmer than the comfort value setting, there

Stop & Start

is no need to alter the value displayed in

Air flow

The heating and air conditioning systems

order to reach the required level of comfort.

► Turn knob 2 to obtain sufficient air flow to

The system compensates automatically and

only operate when the engine is running.

ensure your comfort.

corrects the temperature difference as quickly

Temporarily deactivate the Stop & Start

system to maintain a comfortable temperature

as possible.

in the passenger compartment.

Ease of use and comfort

For maximum cooling or heating of the

On/Off

Automatic comfort mode

passenger compartment, it is possible to

► Press button 5 to activate/deactivate the air

► Press the "AUTO" button 6 to toggle the

exceed the minimum value 14 or the

conditioning system.

mode.

maximum value 28.

When the air conditioning is in operation, to

The active mode appears in the display screen,

► Turn control 1 to the left until "LO"

cool the air more quickly, you can use interior

as described below:

is displayed or to the right until "HI" is

air recirculation for a few moments by pressing

Ensures soft, quiet operation by limiting

displayed.

button 4. Then restore the intake of exterior air.

air flow.

Offers the best compromise between a

The air conditioning does not operate

Air distribution

when the air flow adjustment is set to off.

comfortable temperature and quiet

operation.

Windscreen and side windows (3a).

Provides dynamic, effective air flow.

Switching the system off could result in

Central and side air vents (3b).

discomfort (humidity, misting).

When the engine is cold, the air flow will

Footwells (3c).

only increase to its optimum level

Dual-zone automatic air

gradually, to avoid distributing too much cold

The air distribution can be adapted by combining

air.

the corresponding buttons.

conditioning

In cold weather, it prioritises the distribution of

warm air to the windscreen, the side windows

For optimum comfort, depending on

and the footwells only.

the outside temperature

<15°C: press buttons 3a and 3c.

15°C- 25°C: press buttons 3b and 3c.

Manual mode

>25°C: press button 3b.

If you wish, you can make a different choice from

Temperature.

that suggested by the system, by changing a

Air flow.

setting. The other functions will still be controlled

Air conditioning

Air distribution.

automatically.

With the engine running, the air conditioning is

Recirculation of interior air.

The "AUTO" symbol disappears if you change

designed to operate effectively in all seasons,

Air conditioning on/off.

a setting.

with the windows closed.

Automatic comfort mode.

It enables you to:

Visibility programme.

Deactivating the system

- lower the temperature in summer,

"Mono" function.

► Press button 2 "-" until the fan symbol

- enhance the effectiveness of the demisting

disappears.

function in winter, above 3°C.

Ease of use and comfort

This disables all functions of the dual-zone

For maximum cooling or heating of the

Air conditioning

automatic air conditioning system.

passenger compartment, it is possible to

With the engine running, the air conditioning is

The temperature is no longer regulated. A slight

exceed the minimum value 14 or the

designed to operate effectively in all seasons,

flow of air can still be felt, due to the forward

maximum value 28.

with the windows closed.

movement of the vehicle.

► Push button 1 down until "LO" is

It enables you to:

► Press button 2 "+" to switch the system on

displayed or up until "HI" is displayed.

- lower the temperature in summer,

again.

- enhance the effectiveness of the demisting

"Mono" function

function in winter, above 3°C.

Temperature

The comfort setting for the passenger side

The driver and front passenger can each set the

On/Off

can be indexed to the driver's comfort setting

temperature to suit their preferences.

► Press button 5 to activate/deactivate the air

(mono-zone).

The value shown on the display is a level

conditioning system.

► Press the corresponding button 8 to activate/

of comfort, not a temperature in Celsius or

When the air conditioning is in operation, to

deactivate the function.

Fahrenheit.

cool the air more quickly, you can use interior

The indicator lamp in the button comes on when

► Push button 1 down to decrease the value or

air recirculation for a few moments by pressing

the function is activated.

up to increase it.

button 4. Then restore the intake of exterior air.

The function is deactivated automatically if a

A setting of around 21 provides optimum

passenger uses the temperature control.

The air conditioning does not operate

comfort. Depending on your

when the air flow adjustment is set to off.

requirements, a setting between 18 and 24 is

Visibility programme

normal.

► Press the "visibility" button 7 to demist or

Switching the system off could result in

In addition, we recommend avoiding left/right

de-ice the windscreen and side windows as

discomfort (humidity, misting).

setting differences of more than 3.

quickly as possible.

The system automatically manages the air

On entering the vehicle, if the interior

conditioning, air flow and air intake, and provides

Air distribution

temperature is significantly colder or

optimum distribution towards the windscreen and

► Pressing button 3 successively directs the air

warmer than the comfort value setting, there

side windows.

flow towards:

is no need to alter the value displayed in

► Press the "visibility" button 7 again to stop

- windscreen, side windows and footwells,

order to reach the required level of comfort.

the programme.

- footwells,

The system compensates automatically and

- central vents, side vents and footwells,

corrects the temperature difference as quickly

► Press the "AUTO" button 6 to return to the

- windscreen, side windows, central vents, side

as possible.

Automatic Comfort programme.

vents and footwells,

- central and side vents,

Ease of use and comfort

- windscreen and side windows (demisting or

► Press button 4 to recirculate the interior air or

between the outside and inside of the vehicle,

defrosting).

allow the intake of exterior air.

carry out the following adjustments:

For optimum comfort, depending on

Avoid the prolonged recirculation of

the outside temperature

interior air in order to ensure a good

<15°C: press button 3 until air flow to the

supply of fresh air and reduce the risk of

windscreen, side windows and passenger

misting (especially when several passengers

footwells is activated.

are on board or when the air is cold/damp,

► Press button 5.

15°C-25°C: press button 3 until air flow to

etc.).

► Press button 3a.

the central and side air vents and passenger

► Set knob 1 to a high temperature (minimum

footwells is activated.

21).

>25°C: press button 3 until air flow to the

► Set knob 2 to level 2 or above.

Front demisting - de-icing

central and side air vents is activated.

► Do not press any of the other buttons.

Once demisting has been completed, modify the

Heating

settings according to the desired conditions.

Air flow

For optimum demisting/de-icing in winter, carry

► Press the buttons 2 to increase/decrease the

out the following adjustments:

Dual-zone automatic air

air flow.

conditioning

The air flow symbol (a fan) appears. It is filled in

or emptied gradually, according to the value set.

► Press button 3a.

Recirculation of interior air

► Set knob 1 to the maximum temperature.

The intake of exterior air helps avoid and

► Set knob 2 to the "demisting/de-icing"

eliminate misting of the windscreen and side

symbol.

windows.

► Do not press any of the other buttons.

The recirculation of interior air allows the

Once demisting/de-icing has been completed,

► Press this button to demist or defrost

passenger compartment to be isolated from

modify the settings according to the desired

the windscreen and side windows more

polluted air in areas of heavy traffic and inside

conditions.

quickly.

tunnels.

The system automatically manages the air

Manual air conditioning

conditioning, air flow and air intake, and provides

When required, this function also allows

To demist/prevent misting in high humidity or

optimum distribution towards the windscreen and

faster heating or cooling of the air in the

when there is a big temperature difference

side windows.

passenger compartment.

Ease of use and comfort

► To turn it off, press this button

of the windscreen wiper blades when they

Demisting/de-icing the

again or press "AUTO".

are frozen to the windscreen and helps avoid

The system restarts with the values in use before

the accumulation of snow resulting from the

rear screen and/or the

it was deactivated.

operation of the windscreen wipers.

door mirrors

Heated windscreen and washer jets

Switching on/off

For more information on the Wiper

control stalk and in particular the heated

windscreen and washer jets, refer to the

corresponding section.

With Stop & Start, when demisting

- defrosting has been activated, STOP

mode is not available.

► Press one of these buttons to switch on/off

rear screen and door mirror demisting/de-icing

► With the engine running, press this button to

(depending on version).

Heated windscreen

activate/deactivate the function (confirmed by an

The indicator lamp in the button comes on when

indicator lamp).

the function is activated.

The period of operation depends on the outside

Demisting/de-icing switches off automatically to

temperature.

prevent excessive power consumption.

The function switches off automatically to

Switch off demisting/de-icing as soon

prevent excessive power consumption.

as you no longer consider it necessary,

as decreased power consumption in turn

reduces energy consumption.

Demisting/de-icing only operates with the

engine running.

In cold weather, this system heats the bottom of

the windscreen, as well as the area alongside

the left-hand windscreen pillar.

Without changing the settings for the air

conditioning system, it allows faster release

Ease of use and comfort

Then press "Programmable heating/

Rear heating and air

ventilation".

conditioning

► Select the "Status" tab to activate/deactivate

the system.

► Select the "Other settings" tab to choose

the "Heating" mode, to heat the engine and

passenger compartment, or "Ventilation" to

ventilate the passenger compartment.

► Then set/save the time at which the

preheating temperature will be reached for each

Heating

selection.

This is an additional and separate system which

Press this button to save.

heats the passenger compartment and improves

defrosting performance.

This indicator lamp is lit while the system

With PEUGEOT Connect Nav

is programmed or set in operation

► Press the "Applications" menu.

remotely via the remote control.

If your vehicle is so equipped, the temperature of

It flashes during the whole duration of the

► Press the "Vehicle Apps" tab.

the air distributed by the system is the same as

heating and goes off at the end of the heating

► Press "Temperature programming".

the selection for the front.

cycle or when stopped using the remote control.

► Press the "Status" tab to activate/deactivate

Air flow

Ventilation

the system.

► Press one of the buttons 2 to increase/

This system allows ventilation of the passenger

► Press the "Parameters" tab to select

decrease the air flow.

compartment with exterior air to improve the

"Heating" mode to heat the engine and

temperature experienced on entering the vehicle

passenger compartment or "Ventilation" mode

in summer.

to ventilate the passenger compartment.

Additional heating/

► Then set/save the activation time for each

Programming

ventilation system

selection.

► Press "OK" to confirm.

Only available for Diesel vehicles.

With PEUGEOT Connect Radio

You must allow at least 60 minutes

Press Connect-App to display the main

between programming operations.

page.

Ease of use and comfort

Depending on the outside temperature, a

Off

Diesel engine, and around 30 min. with a

certain amount of pre-conditioning time is

► Pressing and holding this button stops

petrol engine.

necessary in order to reach the programmed

the heating immediately (confirmed by the

temperature by the stored activation time.

red indicator lamp coming on briefly).

The ventilation is activated provided that

This pre-conditioning time lasts up to 45 min.

the battery is sufficiently charged.

The indicator lamp in the remote control

with a Diesel engine and up to 30 min. with a

The heating is activated provided that:

flashes for about 2 seconds if the vehicle

petrol engine.

- the battery charge and the fuel level are

has not received the signal, in which case

sufficient,

you should move to a different location and

- the engine has been started since the

Long range remote control

repeat the command.

previous heating cycle,

(Depending on version.)

- 60 minutes have elapsed between two

This enables you to switch the heating in

Changing the battery

heating requests.

the passenger compartment on or off from a

The indicator lamp in the remote control will

distance.

change to orange if the battery charge is low.

Programmable heating is supplied by the

The remote control has a range of about 0.6

If the indicator lamp is not on, the battery is

vehicle fuel tank. Before use, make sure

miles (1 km) in open country.

discharged.

that you have sufficient fuel. If the fuel tank is

on reserve, you are strongly recommended

not to programme the heating.

The additional heating must always be

switched off while refuelling to avoid any risk

of fire or explosion.

To avoid the risk of poisoning or

asphyxia, the programmable heating

► Use a coin to unscrew the cap and replace

must not be used, even for short periods, in a

the battery.

► Pressing and holding this button starts

closed environment such as a garage or

the heating immediately (confirmed by the

If the system is switched on using the

green indicator lamp coming on briefly).

long-range remote control, the maximum

heating duration is around 45 min. with a

Ease of use and comfort

workshop which is not equipped with an

Programming

Operating conditions

exhaust gas extraction system.

Programming can be carried out from a

- The function is only activated when the

Do not park the vehicle on a flammable

smartphone using the MYPEUGEOT APP

ignition is switched off and the vehicle

surface (dry grass, dead leaves, paper, etc.)

application.

locked.

- Risk of fire!

For more information on Remote functions,

- When the vehicle is not connected, the

refer to the corresponding section.

function is only activated if the battery charge

Glazed surfaces such as the rear screen

level is greater than 50%.

With PEUGEOT Connect Nav system

or windscreen can become very hot in

- When the vehicle is not connected and a

In the Applications menu:

places.

recurring programme is active (e.g. from Monday

Never put objects on these surfaces; never

to Friday), if two temperature pre-conditioning

Press "Car Apps" to display the applications

touch these surfaces - Risk of burns!

sequences are run without the vehicle being

home page.

used, the programme will be deactivated.

Select Temperature conditioning.

Do not throw remote control batteries

away, as they contain metals that are

► Press + to add a programme.

Courtesy lamp

harmful to the environment. Take them to an

► Select the time of entry into the vehicle and

approved disposal point.

the desired days. Press OK.

Automatic switching on/off

► Press ON to activate this programme.

The front courtesy lamp comes on when the key

The temperature pre-conditioning sequence

Temperature conditioning

is removed from the ignition switch.

begins approximately 45 minutes before the

All courtesy lamps come on when the vehicle is

(Electric)

programmed time when the vehicle is connected

unlocked, when one of the corresponding doors

(20 minutes when it is not connected) and is

This function allows you to programme the

is opened and when locating the vehicle using

maintained for 10 minutes after.

temperature in the passenger compartment to

the remote control.

reach a pre-defined, non-modifiable temperature

You can set multiple programmes.

They fade to off after the ignition is switched on

(approx. 21°C) before you enter the vehicle, on

Each one is saved in the system.

and when the vehicle is locked.

the days and at the times of your choice.

To optimise the driving range, we recommend

Take care not to allow objects to come

This function is available when the vehicle is

starting a programme while the vehicle is

into contact with the courtesy lamp.

connected or not connected.

connected.

The fan noise that occurs during

temperature pre-conditioning is perfectly

normal.

Ease of use and comfort

Type 1

Row 2: comes on when one of the rear

doors is opened (sliding side door and

depending on equipment, left-hand side-hinged

door or tailgate).

Always off.

Individual reading lamp

If fitted to the vehicle, these are switched

on and off by means of a manual switch.

With the ignition on, operate the corresponding

switch.

Always lit, ignition on.

Lights up when one of the front or rear

doors is opened.

Always off.

Type 2

Front: comes on when one of the front or

rear doors is opened (sliding side door

and depending on equipment, left-hand

side-hinged door or tailgate).

Always lit, ignition on.

Lighting and visibility

Lighting control stalk

Headlamp dipping

Front foglamps/Rear foglamps

They operate with the sidelamps, dipped

or main beam headlamps on.

Main lighting

► Rotate the ring forwards:

• once to switch on the front foglamps,

► Pull the lighting control stalk to switch

• a second time to switch on the rear

between dipped and main beam headlamps.

foglamps.

Automatic illumination of lamps/daytime

In "AUTO" and sidelamps mode, pull the lighting

► Turn in the opposite direction to switch off.

running lamps

control stalk to switch the main beam headlamps

If the lighting is switched off automatically

Sidelamps only

on directly ("headlamp flash").

("AUTO" position) or the dipped beam

headlamps are switched off manually, the

Dipped or main beam headlamps

Foglamps selection ring

foglamps and sidelamps remain on.

► Rotate the ring backwards to switch the

Rear foglamps

foglamps off; the sidelamps will then switch off.

Operation of the selected lighting is

They only work if the sidelamps are on.

confirmed by the illumination of the

Switching on the foglamps is prohibited

corresponding indicator lamp.

in clear weather or in rain, both day and

night. In these situations, the power of their

beams may dazzle other drivers. They must

only be used in fog or falling snow (rules may

vary depending on country).

Do not forget to switch off the foglamps when

they are no longer necessary.

► Rotate the ring forwards/backwards to turn

them on/off.

When the lighting is switched off automatically

("AUTO" position) the foglamps and the dipped

beam headlamps remain on.

Lighting and visibility

Switching off of the lighting when the

If you keep the direction indicators on for

ignition is switched off

more than 20 seconds, the volume of the

When the ignition is switched off, all of the

audible signal will increase if the speed is

lamps turn off immediately, except for the

above 50 mph (80 km/h).

dipped beam headlamps if automatic guide-

me-home lighting is activated.

Three flashes

► Press briefly upwards or downwards, without

Switching on the lamps after

going beyond the point of resistance; the

switching off the ignition

Travelling abroad

direction indicators will flash 3 times.

If the driver's door is opened, a temporary

If planning to use your vehicle in a

audible signal warns the driver that the lamps

country that drives on the other side of the

Parking lamps

are on.

road, the dipped beam headlamps must be

(Depending on version)

They will go off automatically after a period

adjusted to avoid dazzling oncoming drivers.

Vehicle side marking by lighting the sidelamps

of time that depends on the level of charge in

Consult a PEUGEOT dealer or a qualified

on the traffic side only.

the battery (entering energy economy mode).

workshop.

► Within one minute after switching off the

ignition, operate the lighting control stalk

In some weather conditions (e.g. low

upwards or downwards, depending on the side

Direction indicators

temperature or humidity), misting on the

of the traffic (e.g. when parking on the right, push

internal surface of the glass of the headlamps

the lighting control stalk down to light up on the

and rear lamps is normal, and will disappear

left).

after the lamps have been on for a few

This is confirmed by an audible signal and the

minutes.

lighting of the corresponding direction indicator

lamp on the instrument panel.

Never look too closely at the light beam

► To switch off the parking lamps, return the

of LED technology lamps - risk of serious

lighting control stalk to the central position.

eye injury!

Automatic headlamp

illumination

When a low level of ambient light is detected

► Left or right: lower or raise the lighting control

by a sunshine sensor, the number plate

stalk, beyond the point of resistance.

lamps, sidelamps and dipped beam headlamps

are switched on automatically, without any action

Была ли эта страница вам полезна?

Да!Нет

6 посетителей считают эту страницу полезной.

Peugeot Partner (2022 year). Manual in english — page 4

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.