Peugeot 308 (2022 year). Manual in english — page 2
Instruments
► Then select Safety > Diagnostics.
Rechargeable hybrid vehicles
► Pressing the button located on the end of the
The following information is displayed on the
The total distance recorder is only
wiper control stalk displays the following tabs in
instrument panel:
accessible from the trip computer.
turn:
- Tyre pressures.
For more information on the Trip computer,
- Current information:
- Engine oil level (depending on engine).
refer to the corresponding section.
• Current consumption (Petrol or Diesel).
- Next service due.
• Time counter for Stop & Start (Petrol or
- Driving range associated with the AdBlue® and
Diesel).
Lighting dimmer
the SCR system (BlueHDi Diesel).
• Percentage of the current journey travelled
- Current alerts.
Used to manually adjust the brightness of the
in all-electric driving mode (Rechargeable
instruments and controls to suit the exterior light
hybrid).
This information is also displayed
level.
• Total distance recorder (Rechargeable
automatically every time the ignition is
It is configured in the Settings >
hybrid).
switched on.
Brightness touch screen application.
- Trips "1" then "2":
► In the "Cockpit" category, press or move the
• Average speed.
Total distance recorder
slider to the desired setting.
• Average fuel consumption.
• Distance travelled.
The total distance recorder measures the total
distance travelled by the vehicle since its initial
Trip computer
Trip reset
registration.
Displays information related to the current trip
With the ignition on, the total distance is
► When the desired trip is displayed,
(range, fuel consumption, average speed, etc.).
displayed at all times. It remains displayed for
press the button on the end of the wiper
30 seconds after switching off the ignition. It is
control stalk for more than 2 seconds.
Data displayed on the
displayed when the driver's door is opened, and
Trips "1" and "2" are independent and are used
instrument panel
in the same way.
when the vehicle is locked or unlocked.
Displaying the different tabs
When travelling abroad, you may have to
Definitions
change the distance units (miles or km):
the displayed speed must be in the local
Range
country’s official unit (mph or km/h).
(miles or km)
The unit is changed via the screen's
Distance that can still be travelled with the
configuration application, with the vehicle
fuel remaining in the tank (based on the
stationary.
average fuel consumption over the last few miles
(kilometres) travelled).
22
Instruments
This value may vary following a change in driving
Calculated since the last trip computer
- Navigation system controls and display
1
style or terrain, leading to a significant change in
reset.
of associated information (depending on
current fuel consumption.
equipment).
When the range falls below 19 miles (30 km),
Stop & Start time counter
- Voice recognition (depending on equipment).
dashes are displayed.
(minutes/seconds or hours/minutes)
For safety reasons, always stop the
After filling with at least 5 litres of fuel, the range
vehicle before performing operations
is recalculated and is displayed if it exceeds 62
If your vehicle is fitted with the Stop & Start
that require sustained attention.
miles (100 km).
function, a time counter calculates the time spent
Some functions are not accessible while
Dashes appearing permanently in place of
in STOP mode during a journey.
driving.
numbers while driving indicates a malfunction.
The time counter is reset each time the ignition is
Consult a PEUGEOT dealer or a qualified
switched on.
workshop.
Recommendations
10-inch touch screen
These recommendations are valid for the touch
Current consumption
screen and for the i-Toggles (depending on
(mpg or l/100 km or km/l)
This system gives access to the following
equipment).
Calculated during the last few seconds.
elements:
The touch screen and the i-Toggles screen are
- Time and exterior temperature.
capacitive touch screens.
This function is only displayed at speeds above
- Heating/air conditioning system controls and
Do not use pointed objects on the touch screen.
19 mph (30 km/h).
reminders of settings.
Do not touch the touch screen with wet hands.
- Settings for driving aid functions, comfort and
► Use a soft, clean cloth to clean the touch
Average consumption
safety functions, audio equipment and digital
screen.
(mpg or l/100 km or km/l)
instrument panel.
Calculated since the last trip computer
- Settings of functions specific to rechargeable
Main controls
reset.
hybrid vehicles.
Access to one of the home pages
- Display of visual manoeuvring aid functions.
Return to the first home page
Average speed
- Interactive handbook.
Direct access to the Climate application
(mph or km/h)
- Video tutorials (e.g. screen management,
Calculated since the last trip computer
driving aids, voice recognition).
Direct access to the Shortcuts for
reset.
- Audio equipment and telephone controls with
driving aids
display of associated information.
► Swipe down from the upper edge of the touch
Distance travelled
- Connected services and display of associated
screen to access a list of quick settings (e.g.
(miles or km)
information.
Brightness, Diagnostics).
23
Instruments
► Depending on the pages displayed on the
To obtain information about the other
Energy application
screen, with or without the context menu, scroll
applications not listed here, refer to the sections
the text by swiping with your finger, as with a
describing the audio and telematic systems.
Energy Flow
smartphone.
ADAS
The page shows the operation of the
Show/Hide context menu
Activation/Deactivation and configuration
rechargeable hybrid system in real time.
of the driving aid functions.
Return to the previous page
Climate
Settings for temperature, air flow, etc.
► To change the status of a function, press the
For more information on Dual-zone automatic
description for the corresponding line (change
air conditioning, refer to the corresponding
confirmed by the slider moving to the right/left:
section.
1. Active driving mode
function activated/deactivated).
Activation/Deactivation of the heated steering
2. Petrol engine
Access additional information on the
wheel.
3. Electric motor
function
For more information on the Heated steering
4. Traction battery charge level
Access to function parameters
wheel, refer to the corresponding section.
Seat Options
The energy flows have a specific colour for each
Adding/Removing shortcuts
Activation/Deactivation and configuration
type of driving:
of the seat comfort functions (heating and
- Blue: 100% electrical energy.
Short press, ignition off: system on/off.
massages).
- White: energy from the petrol engine.
Short press, ignition on: mute/restore
For more information on the Heated seats
- Green: energy recovery.
sound.
or on the Multi-point massages, refer to the
Statistics
Long press, ignition on: start standby mode
corresponding section.
(mute sound, screens and clock display off).
Settings
This page shows electrical energy and fuel
Rotation: volume adjustment.
Main settings for the audio system, touch
consumption statistics.
screen and digital instrument panel.
Applications
Activation/Deactivation and configuration of
From the home page, press this button to
the exterior lighting, vehicle access and safety
access the applications wall.
functions.
Energy
From any page, press the touch screen
Access to the rechargeable hybrid system
with three fingers to display the
features (energy flow, consumption statistics,
applications wall.
deferred charging, e-SAVE function).
24
Instruments
1. Average electrical consumption for the current
If the requested range exceeds the
Remotely operable
1
trip (kWh/100 km) and historical values:
available range (not recommended), the
- Blue graph: energy consumed directly from
internal combustion engine starts to recharge
additional functions
the traction battery.
the traction battery up to the requested
(Rechargeable hybrid)
- Green graph: energy regenerated during
threshold. This leads to excessive fuel
deceleration and braking phases to recharge the
consumption.
battery.
2. Average fuel consumption for the current trip
The following functions are
(l/100 km) and historical values (orange graph).
available from the MYPEUGEOT
i-Toggles
APP application, which is
Charging
This system is an additional touch screen
accessible from a smartphone:
associated with the PEUGEOT i-Connect
This page allows you to programme deferred
Advanced. It is designed to provide a
- Managing the traction battery charging
charging.
personalised display of shortcuts to applications
(deferred charging).
For more information on Charging the traction
or presets.
- Managing the temperature pre-conditioning.
battery (Rechargeable hybrid), refer to the
By default, it directs you to the main applications:
- Viewing the state of charge and range of the
corresponding section.
Media, Climate, Navigation, Phone, Mirror
vehicle.
e-SAVE
Screen, etc.
Installation procedure
The shortcuts can be replaced by: radio preset,
The e-SAVE function makes it possible to
► Download the MYPEUGEOT APP app from
temperature preset, pre-selected destination,
reserve all or part of the electrical energy of the
the appropriate online store for your smartphone.
pre-selected contact, pre-selected smartphone,
traction battery to be used later during a journey
► Create an account.
etc.
(e.g. passing through an urban area or an area
► Enter the vehicle’s VIN (code beginning with
For more information on Personalisation -
reserved for electric vehicles).
"VF" on the vehicle registration certificate).
i-Toggles, refer to the corresponding section for
► Select the electric range to be reserved (6
For more information on Identification
the Audio equipment and telematics systems.
miles (10 km), 12 miles (20 km) or the full
markings, refer to the corresponding section.
range MAX) then activate the function.
If the vehicle is exposed to sunlight for an
Network coverage
Activation of the function is confirmed by
extended period, the touch screen can
In order to be able to use the various
the lighting of this indicator lamp on the
become very hot.
remotely operable features, ensure that your
instrument panel and the indication of the energy
Wait a few minutes before using the system.
vehicle is located in an area covered by the
reserve in miles or kms.
mobile network.
► To use the energy reserve, choose the
A lack of network coverage may prevent
Electric driving mode in the mode selector.
communication with the vehicle (for example,
25
Instruments
if it is in an underground car park). In such
cases, the application will display a message
indicating that the connection with the vehicle
could not be established.
26
Access
- Locking/Unlocking the vehicle.
Remote control / Key
2
- Activation/Deactivation of the manual child
lock.
Remote control function
- Activation/Deactivation of the front passenger
airbag.
- Back-up Unlocking/Locking of the doors.
- Switching on the ignition and starting/switching
off the engine.
Without Keyless Entry and Start
► To eject the key or put it back in place, pull
and hold the button.
Depending on version, the remote control can be
used to perform the following remote functions:
Once the built-in key is ejected, always
- Unlocking/Locking/Deadlocking the vehicle.
keep it with you to be able to carry out
- Unlocking - Opening the boot.
the corresponding back-up procedures.
- Remote operation of lighting.
- Folding/Unfolding the door mirrors.
Unlocking the vehicle
- Activating/Deactivating the alarm.
- Locating the vehicle.
- Opening/Closing the windows.
► To unfold or fold the key, press the button.
- Closing the sunroof.
With Keyless Entry and Start
Selective unlocking (driver’s door, boot) is
- Activating the vehicle’s electronic immobiliser.
configured in the Settings > Vehicle
Back-up procedures allow the vehicle to be
touch screen application.
locked/unlocked in the event of a failure of the
Complete unlocking
remote control, the central locking, the battery,
etc. For more information on the Back-up
► Press the unlocking button.
procedures, refer to the corresponding section.
Selective unlocking
Built-in key
Driver’s door and fuel filler flap
The key built into the remote control can be
► Press the unlocking button.
used for the following operations, depending on
► Press it again to unlock the other doors and
version:
the boot.
27
Access
The charging nozzle can be unplugged on the
Locking the vehicle
► Press the locking button again within 3
second press.
seconds to deadlock the vehicle (confirmed by
Complete or selective unlocking, and alarm
the temporary lighting of the direction indicators).
deactivation (depending on version), is confirmed
Closing the windows and sunroof
by the flashing of the direction indicators and the
An audible signal sounds before the start of the
Normal locking
lighting of the daytime running lamps.
movement.
► Press the locking button.
Depending on version, the door mirrors unfold.
► To completely close the windows and,
The locking, and the activation of the alarm
Opening the windows
depending on version, the sunroof, press the
depending on version, is confirmed by the
► To open the windows, press the unlocking
locking button for more than 2 seconds.
lighting of the direction indicators and the
button for more than 3 seconds (depending on
► Press again to stop closing.
daytime running lamps.
version).
Depending on version, the door mirrors fold.
Ensure that no person or object could
► Press again to stop the windows opening.
prevent the correct closing of the
An access (door or boot) that is not
windows and sunroof.
Selective unlocking and opening of
properly closed prevents locking of the
If, on versions with alarm, you want to
the tailgate
vehicle. However, if the vehicle is fitted with
leave the windows and/or sunroof partially
By default, selective unlocking of the tailgate
an alarm, it will be activated after 45 seconds.
open, you must first deactivate the interior
is deactivated and its motorised operation is
If the vehicle is unlocked but the doors or boot
volumetric alarm protection.
activated.
are not subsequently opened, the vehicle
For more information on the Alarm, refer to
► Press and hold this button to unlock
will automatically lock itself again after about
the corresponding section.
the boot and, depending on version,
30 seconds. If the vehicle is fitted with an
trigger the motorised opening of the tailgate.
alarm, it will be reactivated automatically.
When selective unlocking of the tailgate is
Locating the vehicle
activated, the doors and the fuel filler flap remain
Helps you to locate your vehicle from a distance,
Deadlocking
locked.
with the vehicle locked:
If selective unlocking of the tailgate is
- The direction indicators flash for approximately
deactivated, pressing the button unlocks the
10 seconds.
whole vehicle.
- The door mirror spotlamps come on.
Deadlocking renders the interior door
If motorised operation of the tailgate is
controls inoperative. It also deactivates
- The courtesy lamps come on.
deactivated, pressing the button partially
the central locking buttons.
► Press this button.
opens the tailgate.
The horn remains operational.
To lock the vehicle, it is necessary to close
Never leave anyone inside the vehicle
the tailgate again.
when it is deadlocked.
28
Access
Remote lighting of the
For vehicles with a key ignition switch,
than 30 minutes, the system is deactivated to
2
remember to remove the key and turn the
preserve the battery.
lamps
steering wheel to engage the steering lock.
Key recognition zones:
Availability of this function depends on version.
► Press this button. The sidelamps,
Locking the vehicle
dipped beam headlamps, number plate
Driving with the doors locked could make
lamps and door mirror spotlamps come on for 30
it more difficult for the emergency services
seconds.
to enter the passenger compartment in an
Pressing again before the end of the timed
emergency.
period switches off the lamps immediately.
As a safety precaution, remove the key from
the ignition or take the electronic key with you
Advice
when leaving the vehicle, even for a short
Remote control
time.
The remote control is a sensitive, high-
frequency device; avoid handling it in your
Purchasing a second-hand vehicle
Zone A: welcome lighting on approaching
pocket, due to the risk of unintentionally
Have the key codes memorised by a
the vehicle (between 2 and 5 metres from the
unlocking the vehicle.
PEUGEOT dealer, to ensure that the keys
vehicle).
Avoid pressing the remote control buttons
in your possession are the only ones able to
Zone B: automatic locking on moving away from
while out of range of the vehicle, due to
start the vehicle.
the vehicle (about 2 metres from the vehicle).
the risk of rendering the remote control
Zone C: automatic unlocking on approaching
inoperative. It would then be necessary to
the vehicle (between 1 and 2 metres from the
reset it.
vehicle).
Proximity Keyless Entry
The remote control does not work when the
Automatic functions are configured in the
key is in the ignition switch, even when the
and Start
Settings > Vehicle touch screen
ignition is switched off.
This is a Keyless Entry and Start system.
application.
It enables automatic vehicle locking/unlocking
Anti-theft protection
simply by detecting the electronic key.
Do not modify the electronic vehicle
As long as the driver has the electronic key
immobiliser, as this might result in
on their person, the vehicle unlocks as they
malfunctions.
approach and locks when they walk away.
If the electronic key is present in an area
between 2 and 5 m from the vehicle for more
29
Access
Unlocking the vehicle
the vehicle, use the remote control or press
With the doors and boot closed, the vehicle
the driver's door handle.
locks:
If using the door handle does not lock/unlock
► Either automatically, upon leaving zone B, if
the vehicle, bring the electronic key closer
the automatic functions are activated.
and repeat the desired action.
► Or by gently pressing the driver's door
handle.
Locking is confirmed by the lighting of the
Selective unlocking
direction indicators, and by an audible signal
Driver’s door and fuel filler/charging flap
when the vehicle is locked upon walking away.
They unlock:
It is not possible to lock the vehicle if the
Selective unlocking (driver’s door, boot) is
► Either automatically when approaching the
electronic key is left inside the vehicle.
configured in the Settings > Vehicle
driver’s door, if the automatic functions are
touch screen application.
activated.
Deadlocking
► Or by gently pressing the driver's door
Complete unlocking
handle.
The vehicle (doors and boot) unlocks:
► Once inside the vehicle, to unlock all
► Either automatically as the driver approaches
accesses, press the central unlocking button or
Deadlocking renders the interior door
in zone C, if the automatic functions are
pull the opening control on any door.
controls inoperative. It also deactivates
activated.
the central locking buttons.
► Or by gently pressing the driver's door handle
Selective unlocking of the tailgate
The horn remains operational.
or the button on the boot.
The tailgate unlocks automatically as you
Never leave anyone inside the vehicle
Unlocking, and alarm deactivation (depending
approach the rear of the vehicle.
when it is deadlocked.
on version), is confirmed by the flashing of the
► Press the tailgate control to open the boot.
direction indicators and lighting of the daytime
The doors remain locked.
running lamps.
Depending on version, the door mirrors unfold.
Locking the vehicle
If the electronic key remains around the
vehicle (zones A, B or C) for more than
Normal locking
► Gently press the driver's door handle to lock
15 minutes without action, the automatic
the vehicle.
functions are deactivated. To unlock or lock
► Press it again within 3 seconds to deadlock
the vehicle (confirmed by the temporary lighting
of the direction indicators).
30
Access
If one of the doors or the boot is still open
vehicle is started, the automatic unlocking
Manual
2
or if the electronic key for the Keyless
and locking functions will be reactivated.
► Press these buttons to lock/unlock the vehicle
Entry and Start system has been left inside
- If the welcome lighting is triggered
(doors and boot) from inside the passenger
the vehicle, central locking will not take place.
several times in succession without the
compartment.
vehicle subsequently being started, it will be
deactivated.
Central locking does not take place if any
If the vehicle is unlocked but the doors or
- All "hands-free" functions switch to
of the doors are open.
tailgate are not subsequently opened, the
vehicle will automatically lock itself again after
hibernation mode after 21 days without being
about 30 seconds. If fitted to the vehicle, the
used. To restore these functions, unlock the
When locking/deadlocking from the
alarm is automatically reactivated (if
vehicle using the remote control and start the
outside
previously activated).
engine.
When the vehicle is locked or deadlocked
from the outside, the indicator lamp in the
Electrical interference
locking button flashes and the buttons are
Automatic folding/unfolding of the door
The electronic key may not work if it is
inactive.
mirrors is configured in the Settings >
close to an electronic device (e.g. mobile
► After normal locking, pull one of the
Vehicle touch screen application.
telephone (switched on or on standby), laptop
interior door controls to unlock the vehicle.
computer, strong magnetic fields). If this
► After deadlocking, you must use the
As a safety measure, never leave the
occurs, move the electronic key away from
remote control, the "Keyless Entry and
vehicle, even for a short time, without
the electronic device.
Start" system or the built-in key to unlock the
taking the Keyless Entry and Start system’s
vehicle.
electronic key with you.
Be aware of the risk of theft of the vehicle if
the key is present in one of the defined areas
Central locking
Automatic (anti-intrusion
while the vehicle is unlocked.
security)
The doors and boot lock automatically while
In order to preserve the battery in the
driving (speed above 6 mph (10 km/h)).
electronic key and the vehicle's battery:
To deactivate/reactivate this function (activated
- The unlocking on approach function
by default):
(zone C) automatically switches to hibernation
► Press the locking button until a confirmation
mode after several days (approximately one
message appears.
week) without being used. To unlock the
vehicle, use the remote control or press on
the driver’s door handle. The next time the
31
Access
Transporting long or voluminous
In the first case, change the remote control
Front left-hand door
objects
battery.
► Insert the key into the lock and turn it towards
Press the central locking control to drive
In the second case, reinitialise the remote
the front or rear of the vehicle to lock and unlock
with the boot open and the doors locked.
control.
the door.
Otherwise, every time the speed of the
Refer to the corresponding sections.
vehicle exceeds 6 mph (10 km/h), the sound
Other doors
of the locks rebounding will be heard and an
Unlocking
alert will be displayed.
► Pull the interior door opening control.
Locking
Back-up procedures
► Insert the key in the door lock.
► Turn the key towards the front or the rear to
Lost keys, remote control,
unlock or lock the vehicle.
electronic key
If the vehicle is fitted with an alarm, it will
Go to a PEUGEOT dealer with the vehicle's
not be activated when locking with the
registration certificate, your personal
key.
identification documents and if possible, the label
If the alarm is activated, the siren sounds
bearing the key code.
when the door is opened; switch on the
The PEUGEOT dealer will be able to retrieve the
ignition to stop it.
key code and the transponder code, enabling a
new key to be ordered.
► Open the doors.
Central locking not
► For the rear doors, check that the child lock
Complete unlocking/locking
is not on.
functioning
Refer to the corresponding section.
of the vehicle with the key
Use these procedures in the following cases:
► Gently insert the key into the latch located in
Use this procedure in the following situations:
- Central locking malfunction.
the door lock, then turn the latch an eighth of a
- Remote control battery discharged.
- Battery disconnected or discharged.
turn towards the outside of the door.
- Remote control malfunction.
In the event of a malfunction of the
► Close the doors and check from the outside
- Vehicle battery discharged.
central locking system, the battery must
that the vehicle is locked.
- Vehicle in an area subject to strong
be disconnected to ensure that the vehicle is
electromagnetic interference.
locked fully.
32
Access
Changing the battery
► Remove the flat battery from its housing.
Risk of explosion if the battery is
2
► Put the new battery in place, respecting the
replaced with an incorrect type!
A message is displayed on the instrument panel
polarity. Start by inserting it into the contacts
Replace the battery with the same type.
when the battery needs changing.
located in the corner, then clip the cover onto
Battery type: CR2032/3 volts.
the unit.
Risk of explosion or leaking of
Without Keyless Entry and Start
► Reinitialise the remote control.
inflammable liquid or gas!
For more information on Reinitialising the
Do not use in/store in/place in an environment
remote control, refer to the corresponding
where the temperature is extremely high or
section.
where the pressure is extremely low due to
very high altitude.
Do not throw remote control batteries
Do not try to burn, crush or cut a used battery.
away, as they contain metals that are
harmful to the environment. Take them to an
approved disposal point.
Reinitialising the remote
control
This equipment contains a button type
Following replacement of the battery or in
battery.
the event of a fault, it may be necessary to
Do not swallow the battery. Risk of chemical
reinitialise the remote control.
burns!
With Keyless Entry and Start
Swallowing the battery can cause serious
Without Keyless Entry and Start
internal burning in only 2 hours and can be
fatal.
If batteries have been swallowed or inserted
into a part of the body, seek immediate
medical advice.
Keep new and used batteries out of the reach
of children.
If the battery compartment does not close
properly, stop using the product and keep it
out of the reach of children.
► Unclip the cover by inserting a small
screwdriver in the slot and lift the cover.
► Switch the ignition off.
33
Access
► Turn the key to position 2 (Ignition on).
If the fault persists after reinitialisation, contact
When selective unlocking is activated,
► Immediately press the closed padlock button
a PEUGEOT dealer or a qualified workshop
the electronic key must be close to the
for a few seconds.
without delay.
rear of the vehicle.
► Switch off the ignition and remove the key
from the ignition switch.
The tailgate is not designed to hold a
Doors
The remote control is now fully operational
bicycle carrier.
again.
Opening
With Keyless Entry and Start
Closing the tailgate
From outside
► Lower the tailgate using the interior grips.
► After unlocking the vehicle or with the
► Release the grips and press down on the
"Keyless Entry and Start" system electronic key
outside of the tailgate to close it.
in the recognition zone, pull the door handle.
In the event of a malfunction or if you
experience difficulty opening or closing
From inside
the tailgate, have it checked by a PEUGEOT
► Pull the interior opening control of a door; this
dealer or a qualified workshop without delay,
unlocks the vehicle completely.
to avoid the issue deteriorating and prevent
With selective unlocking activated:
any risk of the tailgate dropping, potentially
- Opening the driver's door unlocks
causing serious injury.
the driver's door only (if the vehicle has not
already been completely unlocked).
► Insert the mechanical key (incorporated into
Back-up release
- Opening one of the passenger doors
the remote control) into the lock to open the
unlocks the rest of the vehicle.
To manually unlock the boot in the event of a
vehicle.
battery or central locking failure.
► Place the electronic key against the back-up
reader on the steering column and hold it there
Unlocking
until the ignition is switched on.
Boot
► Fold the rear seats to gain access to the lock
► With a manual gearbox, place the gear lever
from inside the boot.
in neutral then fully depress the clutch pedal.
Opening the tailgate
► With an automatic gearbox, while in mode
► With the vehicle unlocked or with the
P, depress the brake pedal.
electronic key in the recognition zone, press the
► Switch on the ignition by pressing the
central tailgate control.
"START/STOP" button.
► Raise the tailgate.
34
Access
essential to deactivate the motorised
2
operation of the tailgate.
Motorised operation
The motorised operation of the tailgate is
configured in the Settings > Vehicle
touch screen application.
► Insert a small screwdriver into hole A of the
lock to unlock the boot.
► Move the latch to the left.
Never insert a finger in the locking
system of the motorised tailgate - risk of
Locking after closing
serious injury!
If the fault persists after closing again, the boot
will remain locked.
To avoid the risk of injury through
pinching or trapping, before and during
Motorised tailgate (SW)
operation of the motorised tailgate:
- ensure that there is no-one close to the
(Depending on version)
rear of the vehicle.
The motorised tailgate must only be operated
- monitor the activity of the rear passengers,
with the vehicle stationary.
particularly any children.
There are several ways of operating the tailgate:
A. Using the Keyless Entry and Start system’s
electronic key
Bicycle carrier/Towing device
B. Using the exterior tailgate control
The motorised tailgate is not designed to support
C. Using the interior tailgate control
a bicycle carrier.
D. Using the control on the dashboard
When installing a bicycle carrier on the towing
device with connection of the cable to the trailer
Opening
socket, the motorised operation of the tailgate
► A long press on the central button A of the
Check that there is enough space to
will be automatically deactivated.
electronic key.
allow for the movement of the motorised
If using a towing device or bicycle carrier
or
tailgate.
not recommended by PEUGEOT, it is
► A short press on the exterior tailgate control
B, with the electronic key on your person.
35
Access
or
The "Hands-free tailgate/opening"
► Position yourself behind the vehicle by the
► Two consecutive presses on the control D on
function is configured in the Settings >
number plate and perform a "kicking" movement
the dashboard.
Vehicle touch screen application.
in the "OK" detection zone.
The "kicking" movement must be given forwards,
The tailgate opens, either completely by
Ensure that you are steady on your feet
smoothly, not too fast and with a vertical
default, or to the position memorised
before performing the "kicking"
movement from low to high. Raise the foot
beforehand.
movement.
sufficiently and remove it immediately.
If motorised operation is not activated, these
Take care not to touch the exhaust system
Acknowledgement of the "kicking" movement
actions release the tailgate (partially-open
which may be hot - risk of burns!
is confirmed by the lighting of the direction
position).
indicators.
When the vehicle is locked, the request to
Rechargeable hybrid vehicles
open the boot with one of the controls A
The function is not available when the
"Sideward kicking" movements do not
or B unlocks the vehicle, or only the boot if
vehicle is connected.
work. If the "kicking" movement has not
selective unlocking is activated, prior to the
been detected, wait at least 2 seconds before
opening of the boot.
repeating the movement.
Do not perform repetitive "kicking"
Closing
movements.
► A short press on the interior tailgate control C.
If the motorised tailgate has not started to open,
It is possible to interrupt the operation of
check that:
the tailgate at any point.
- the function is activated.
Pressing one of these controls again
- the electronic key is on your person, outside
interrupts the movement that is underway.
the vehicle in the rear recognition area.
- the "kicking" movement was performed in the
detection zone, close enough to the bumper.
Hands-free function (Hands-
- the foot was removed from the bumper quickly
Free Tailgate Access)
enough.
With the electronic key on your person, this
When the vehicle is locked, the request
function allows the motorised tailgate to be
to open the tailagte with this function
opened, closed or stopped via a "kicking"
unlocks the vehicle, or only the tailgate if
movement under the rear bumper.
36
Access
selective unlocking is activated, prior to the
Towing device
The tailgate must be stationary.
2
opening of the tailgate.
The installation of a towing device may
With resumption of the motorised function
Closing the tailgate with the “Hands-Free
disturb the detection system.
The motorised tailgate function can be activated
Tailgate Access” function enables you to lock
To avoid unintentionally opening the tailgate
manually.
the vehicle.
while operating the towing device:
► With the boot open: vigorously move the
► remove the electronic key from the
tailgate a little in the closing direction to activate
recognition zone, with the tailgate closed.
Recommendations on the hands-free
motorised closing.
For more information on the Towing device
function (Hands-Free Tailgate Access)
► With the boot partly open: vigorously move
with quickly detachable towball, refer to the
the tailgate a little in the opening direction to
If it does not work, check that the electronic key
corresponding section.
activate motorised opening.
is not exposed to a source of electromagnetic
interference (e.g. smartphone).
Without resumption of the motorised
The function may be deactivated or affected if
Memorising an opening
function
there is rain or snow.
position
► Move the tailgate as slowly and smoothly as
The function may not work correctly with a
To limit the opening angle of the motorised
possible.
prosthetic leg.
tailgate:
Assistance from the gas struts is no longer
In some circumstances, the tailgate may open or
► move the tailgate to the desired position
available when opening and closing the
close by itself, particularly when:
manually or by pressing the button.
motorised tailgate manually. Resistance to
- hitching up or removing a trailer;
► press button C or the exterior control B for
opening and closing is therefore quite normal.
- fitting or removing a bicycle carrier;
more than 3 seconds (memorisation is confirmed
- loading or unloading bicycles on/from a bicycle
In case of the motor overheating
by a brief audible signal).
carrier;
Repeatedly opening and closing the
A new memorisation operation cancels the
- depositing or lifting something behind the
tailgate can cause overheating of its electric
previous one.
vehicle;
motor, after which opening and closing will not
- an animal approaches the rear bumper;
Memorising is not available until the
be possible.
- washing the vehicle;
height of opening is more than or equal
Allow the electric motor to cool down for at
- maintenance is performed on the vehicle;
to 1 metre between the low position and the
least 10 minutes before carrying out any
- accessing the spare wheel.
high position of the tailgate.
manoeuvre.
To avoid such operating problems, keep the
If you are unable to wait, operate it manually.
electronic key away from the recognition zone or
Manual operation
deactivate the hands-free function.
The tailgate can be manoeuvred by hand, even
with motorised operation activated.
37
Access
Manual closing of the
Alarm
When the vehicle is parked, the alarm
will not be triggered if the vehicle is
motorised tailgate in case of
(Depending on version)
knocked.
failure
Self-protection function
This operation is only necessary in the case of
failure of the tailgate motor.
The system checks whether any of its
If the failure originates from the battery, it is
components are out of service.
recommended to recharge it or change it with the
The alarm is triggered if the battery, the central
tailgate closed.
control or the siren wiring is put out of service or
In this situation, a significant force may be
damaged.
needed to close the tailgate.
Work on the alarm system
► Close it gently without slamming, as slowly as
System which protects and provides a deterrent
Consult a PEUGEOT dealer or a
possible, by pushing at the centre of the tailgate.
against theft and break-ins.
qualified workshop.
Do not lower the tailgate by pushing at
Exterior perimeter monitoring
one of its sides - risk of damage!
The system checks for opening of the vehicle.
Locking the vehicle with full
The alarm is triggered if anyone tries to open a
door, the boot or the bonnet, for example.
alarm system
Precautions in use
Interior volumetric monitoring
Activation
In wintry conditions
The system checks for any variation in volume in
To avoid any operating problems, remove
► Switch off the ignition and exit the vehicle.
the passenger compartment.
the snow or wait until the ice melts before
► Lock or deadlock the vehicle using the
The alarm is triggered if anyone breaks a
requesting motorised opening of the tailgate.
remote control or by pressing on the driver's
window, enters the passenger compartment or
door handle.
moves inside the vehicle.
When the monitoring system is active, the red
When washing
Anti-tilt monitoring
indicator lamp in the button flashes once per
When washing the vehicle in an
The system checks for any change in the attitude
second and the direction indicators come on for
automatic car wash, do not forget to lock and
of the vehicle.
about 2 seconds.
move away from the vehicle to prevent any
The alarm goes off if the vehicle is lifted or
The exterior perimeter monitoring is activated
risk of unwanted opening.
moved.
after 5 seconds and the interior volumetric
monitoring after 45 seconds.
38
Access
The alarm does not activate when
Locking the vehicle
Reactivating the interior volumetric
2
locking automatically from a distance.
and anti-tilt monitoring
with exterior perimeter
► Deactivate the exterior perimeter monitoring
If an opening (door, boot or bonnet) is not
monitoring only
by unlocking the vehicle using the remote control
properly closed, the vehicle is not locked,
Deactivate the interior volumetric and anti-tilt
or the Keyless Entry and Start system.
but the exterior perimeter monitoring will be
monitoring to avoid the unwanted triggering of
The indicator lamp in the button goes off.
activated after 45 seconds, at the same time
the alarm, in certain cases such as:
► Reactivate all monitoring by locking the
as the interior volumetric monitoring.
- Slightly open window.
vehicle using the remote control or the Keyless
- Washing the vehicle.
Entry and Start system.
- Changing a wheel.
The red indicator lamp in the button once again
Deactivation
- Towing the vehicle.
flashes every second.
► Press one of the remote control unlocking
- Transport on a ship or ferry.
buttons:
Triggering of the alarm
Short press.
Deactivating the interior volumetric
This is indicated by sounding of the siren
and anti-tilt monitoring
and flashing of the direction indicators for 30
Long press.
► Switch off the ignition and within 10 seconds
seconds.
press the alarm button until its red indicator lamp
Depending on the country of sale, certain
or
is on fixed.
monitoring functions remain active until the alarm
► Unlock the vehicle by pressing the driver’s
► Get out of the vehicle.
has been triggered eleven times consecutively.
door handle.
► Immediately lock the vehicle using the remote
When the vehicle is unlocked using the remote
The monitoring system is deactivated: the
control or the Keyless Entry and Start system.
control or the Keyless Entry and Start system,
indicator lamp in the button goes off and the
Only the exterior perimeter monitoring is
rapid flashing of the red indicator lamp in the
direction indicators flash for about 2 seconds.
activated; the button's red indicator lamp flashes
button informs you that the alarm was triggered
After unlocking using the remote
once every second.
during your absence. When the ignition is
control
switched on, this flashing stops.
To take effect, this deactivation must be
If the vehicle automatically locks itself again
carried out after each time the ignition is
(as happens if a door or the boot is not
Failure of the remote control
switched off.
opened within 30 seconds of unlocking), the
To deactivate the monitoring functions:
monitoring system is automatically activated.
► Unlock the vehicle using the key in the front
left-hand door lock.
► Open the door; the alarm is triggered.
39
Access
► Switch on the ignition; this stops the alarm.
The electric window controls remain
Electric windows
The indicator lamp in the button goes off.
operational for approximately 45 seconds
after switching off the ignition.
Locking the vehicle without
After that time, the controls are disabled. To
reactivate them, switch the ignition on again.
activating the alarm
► Lock the vehicle using the key (built-in the
Anti-pinch
remote control) in the front left-hand door lock.
If the window meets an obstacle while rising, it
Automatic activation
stops and immediately partially lowers again.
(Depending on version)
Deactivating the rear
The system is activated automatically 2 minutes
1.
Left-hand front
after the last door or the boot is closed.
2.
Right-hand front
controls for the rear electric
► To avoid triggering the alarm on entering the
3.
Left-hand rear
windows
vehicle, first press the unlocking button on the
4.
Right-hand rear
For your children's safety, press control 5
remote control or unlock the vehicle using the
5.
Deactivation of electric window controls
to deactivate the controls for the rear
"Keyless Entry and Start" system.
located by rear seats
electric windows, irrespective of their positions.
The red indicator lamp in the button comes on.
Malfunction
Manual operation
The rear electric windows can still be controlled
When the ignition is switched on, the fixed
► To open/close the window, press/pull the
using the driver's controls.
lighting of the red indicator lamp in the button
switch without passing the point of resistance;
indicates a system malfunction.
the window stops as soon as the switch is
Reinitialising the electric
Have it checked by a PEUGEOT dealer or a
released.
windows
qualified workshop.
After reconnecting the battery, or in the event
Automatic operation
of abnormal window movement, the anti-pinch
► To open/close the window, press/pull the
function must be reinitialised.
switch past its resistance point: the window
The anti-pinch function is disabled during the
opens/closes completely when the switch is
following sequence of operations.
released.
For each window:
Operating the switch again stops the movement
► Pull the control until the window is fully
of the window.
closed.
40
Access
► Release the control, then pull it again for at
Use only plastic scrapers to remove snow or
2
least one second.
ice from the sunroof.
If an electric window meets an obstacle
Regularly check the condition of the
during operation, the movement of the
sunroof seals (e.g. presence of dust,
window must be reversed. To do this, press
dead leaves).
the relevant control.
If using a car wash, check first that the roof is
When the driver operates the passengers’
correctly closed and keep the high-pressure
electric window controls, it is important to
jet at least 30 centimetres from the seals.
ensure that nothing can prevent the window
The sunroof can be operated when the ignition
from closing properly.
It is important to ensure that passengers use
is turned on (if the battery is charged enough),
Never leave the vehicle with the sunroof
the electric windows correctly.
with the engine running, in STOP mode of Stop
open.
& Start, and up to 45 seconds after turning off
Pay particular attention to children when
the ignition.
operating the windows.
Operation
Be aware of passengers and/or other persons
Precautions
When opening the sunroof fully, the movable
present when closing windows remotely using
Do not put your head or arms through the
glass moves to a partially open position, then
the electronic key.
sunroof while the vehicle is moving - risk
slides over the roof. Any intermediate position is
Do not put your head or arms through the
of serious injury!
possible.
open windows when the vehicle is moving -
risk of serious injury!
Before operating the sunroof control
Do not operate the sunroof if transverse
button, ensure that no object or person
roof bars are fitted - risk of serious
might prevent the movement.
damage!
Sunroof
Pay particular attention to children when
Do not place heavy loads on the movable
operating the sunroof.
The sunroof consists of a movable glass panel
glass panel of the sunroof.
If something is trapped when operating the
that slides over the roof and a blind that can
sunroof, reverse the movement of the sunroof
be opened independently. Opening the sunroof
If the sunroof is wet, following a rain
by pressing the control button in question.
automatically opens the blind.
shower or washing the vehicle, wait until
The driver must ensure that passengers use
► To operate the panoramic sunroof, use the
it is completely dry before operating it.
the sunroof correctly.
button in the roof console.
Do not operate the sunroof if it is covered by
Any manual intervention on the position of
snow or ice - risk of damage!
the sunroof may disturb the anti-pinch device.
Perform a reinitialisation.
41
Access
Anti-pinch system
► To close the blind, push its handle forwards
until the desired position is reached.
If the sunroof encounters an obstacle when
closing, the movement is automatically reversed.
Reinitialisation
Opening/closing the sunroof
Reinitialisation is required after reconnecting the
► To open the sunroof, use the part of the
battery, or if the sunroof malfunctions or moves
button located towards the rear.
in a jerky manner.
► To close the sunroof, use the part of the
► Check that nothing is affecting the movement
button located towards the front.
of the sunroof and that the seals are clean.
Operating the button
► With the ignition on, press and hold
the front part of the button to close the
► Pressing the button beyond its point of
sunroof.
resistance opens or closes the sunroof fully.
The sunroof closes step by step. When fully
► Pressing the button again stops the
closed, it performs a slight opening/closing
movement in progress.
movement.
► By keeping the button pressed (without going
► Release the button 1 second after the end of
beyond the point of resistance), the movement of
the movement.
the glass stops when this button is released.
► When the sunroof is closed: pressing once
without passing the point of resistance moves it
to the partially open position.
► When the sunroof is partially open: pressing
once on the front part of the button, without
going beyond the point of resistance, closes it
completely.
The sunroof and windows can be closed
by holding down the remote control
locking button.
Press again to stop the manoeuvre.
Opening/closing the blind
► To open the blind, pull its handle backwards
until the desired position is reached.
42
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст