Peugeot 308 (2022 year). Manual in english — page 8
Driving
Standard view
This view is not recommended for carrying out a
complete manoeuvre.
This view is only available by selection in the left-
hand side menu.
Side views
The left-hand/right-hand side view allows you to
view the surroundings of each side of the vehicle
Depending on the context, the area behind or in
(e.g. pavement, low wall, other vehicle parked
front of your vehicle is displayed on the screen.
next to it).
When engaging reverse gear with the engine
The blue lines (at the rear)/orange lines (at the
running, or when reversing at up to 6 mph
front) 1 represent the width of your vehicle, with
(10 km/h), this system warns of approaching
the mirrors unfolded; their direction changes
obstacles (e.g. pedestrian, cyclist, vehicle, truck,
according to the position of the steering wheel.
motorcycle) in the blind spots of the vehicle,
The red line 2 represents a distance of 30 cm
using the radars installed in the bumper.
from the rear or front bumper; the two blue lines
The system detects obstacles moving at
(at the rear)/orange lines (at the front) 3 and
► Select the relevant view in the view from
between 2 mph and 6 mph (3 km/h and 10 km/h)
4 represent 1 m and 2 m respectively.
above the vehicle.
at a maximum distance of 40 m.
This view is available automatically or by
The selected area turns yellow and the side view
The system operates in addition to the Parking
selection in the left-hand side menu.
appears in the middle of the screen.
sensors, Visiopark 1 or Visiopark 2 functions
This view is not recommended for carrying out a
(depending on version).
Panoramic view
complete manoeuvre.
For more information about the Parking
sensors, Visiopark 1 or Visiopark 2 functions,
refer to the corresponding sections.
Rear traffic alert
The driver must monitor their
For more information, refer to the
surroundings before and during the
General recommendations on the use
whole manoeuvre. Drive slowly and carefully
of driving and manoeuvring aids.
in reverse gear, in the event of reduced or no
The rear or front panoramic view allows you to
visibility.
leave a parking space by anticipating the arrival
of vehicles, pedestrians or cyclists.
148
Driving
Operating principle
Activation/Deactivation
panel, accompanied by the display of a message
6
and an audible signal.
It is configured in the ADAS touch screen
Have it checked by a PEUGEOT dealer or a
application.
qualified workshop.
The system's status is saved when the ignition is
switched off.
Operating limits
The system may not work in the following cases:
- Towing a trailer.
- Using a bicycle carrier on a towing device.
- Extreme temperature changes.
- If the rear bumper is damaged.
- Accumulation or projection of external
elements (e.g. mud, ice, snow), application of
stickers.
When an approaching obstacle is detected, the
It is possible that warnings are not given,
symbol 1 or 2 flashes on the touch screen, in the
are given too late or seem unjustified.
Parking sensors view or in the various contextual
Consequently, always stay in control of your
views of the Visiopark 1 or Visiopark 2 functions
vehicle and be prepared to react at any time
(depending on version).
to avoid an accident.
The symbol is complemented by an audible
signal when the vehicle is reversing.
If the rear bumper is to be repainted,
An obstacle is approaching in the
contact a PEUGEOT dealer or a qualified
blind spot on the rear right-hand/
workshop; certain types of paint could
left-hand side or on both sides of the vehicle.
interfere with the operation of the radars.
In the event of a malfunction of these functions
or of the touch screen, or if the driver deactivates
the views from these functions on the touch
Malfunction
screen, detection of an approaching obstacle
In the event of a malfunction when
is still indicated by the audible signal when the
engaging reverse gear, during reversing
vehicle is reversing.
or if the driver attempts to activate the system,
this warning lamp lights up on the instrument
149
PEUGEOT & TOTAL
PARTNERS IN PERFORMANCE!
For over 25 years, the PEUGEOT TOTAL partnership has pushed the boundaries
of performance to achieve success in the most difficult of conditions, with
victories in the Le Mans 24 Hours, in the Dakar Rally and also those by all
of our Rally customers around the world. To obtain these exceptional results,
the Peugeot Sport teams chose TOTAL QUARTZ, a high-tech lubricant that
protects the engine in the most extreme conditions.
TOTAL QUARTZ protects your engine against the
effects of tim e.
TOTAL QUARTZ INEO XTRA FIRST 0W-20 is a very high-performance
lubricant developed jointly by the Peugeot and Total R&D teams.
Specially formulated for the engines in Peugeot vehicles, its innovative
technology significantly reduces CO2 emissions and effectively protects your
engine against clogging.
Practical information
fuels could prevent the engine from operating
signal. When driving, this message and audible
Compatibility of fuels
7
correctly. In these temperature conditions, use
signal are repeated with increasing frequency as
winter-type Diesel fuel and keep the fuel tank
the fuel level drops towards 0.
more than 50 % full.
You must refuel as soon as possible to avoid
Petrol fuels conforming to the EN228 standard
At temperatures below -15 °C (+5 °F) to avoid
running out of fuel.
containing up to 5% and 10% ethanol
problems starting, it is best to park the vehicle
For more information on Running out of fuel
respectively.
under shelter (heated garage).
(Diesel), refer to the corresponding section.
A small arrow by the warning lamp
Travelling abroad
indicates which side of the vehicle the
Diesel fuels conforming to the EN590, EN16734
Certain fuels could damage your vehicle’s
fuel filler flap is located on.
and EN16709 standards and containing up to
engine.
7%, 10%, 20% and 30% fatty acid methyl ester
In certain countries, the use of a particular
Stop & Start
respectively. The use of B20 or B30 fuels, even
fuel may be required (specific octane rating,
Never refuel with the engine in STOP
occasionally, imposes special maintenance
specific trade name, etc.) to ensure correct
mode; you must switch off the ignition.
conditions referred to as "Arduous conditions".
operation of the engine.
For all additional information, consult a dealer.
Refuelling
Paraffinic Diesel fuel conforming to the EN15940
Refuelling
Any addition of fuel must be in quantities of at
standard.
least 10 litres, in order to be registered by the
Fuel tank capacity: approximately 52 litres
fuel gauge.
The use of any other type of (bio) fuel
(Petrol or Diesel) or 40 litres (Rechargeable
Opening the filler flap may create a noise caused
(vegetable or animal oils, pure or diluted,
hybrid).
by an inrush of air. This vacuum is entirely
domestic fuel, etc.) is strictly prohibited (risk
Reserve level: approximately 6 litres.
normal, resulting from the sealing of the fuel
of damage to the engine and fuel system).
system.
Low fuel level
To refuel in complete safety:
The only fuel additives authorised for use
When the low fuel level is reached,
► Always switch off the engine.
are those that meet the B715001 (petrol)
this warning lamp lights up on the
or B715000 (Diesel) standards.
instrument panel, accompanied by the display of
a message and an audible signal. When it first
comes on, about 6 litres of fuel remain.
Diesel at low temperature
Until sufficient fuel is added, this warning lamp
At temperatures below 0 °C (+32 °F), the
appears every time the ignition is switched on,
formation of paraffins in summer-type Diesel
accompanied by the message and the audible
151
Practical information
► To open the filler flap, press the flap opening
The vehicle is fitted with a catalytic converter,
When a petrol filler nozzle is introduced into the
button or press the rear edge of the filler flap
which helps to reduce the level of harmful
fuel filler neck of a Diesel vehicle, it comes into
(depending on version).
emissions in the exhaust gases.
contact with the flap. The system remains closed
For petrol engines, you must use unleaded
and prevents filling.
Rechargeable hybrid vehicles
fuel.
Do not persist but introduce a Diesel type
After pressing the button, it may take a
The filler neck is narrower, allowing only
filler nozzle.
few minutes for the filler flap to open.
unleaded petrol nozzles to be inserted.
If the flap becomes stuck, press and hold the
The misfuel prevention device does not
button for more than 3 seconds.
If you have put in the wrong fuel for
prevent filling with a jerrycan, regardless
the vehicle, you must have the fuel
of the fuel type.
► Select a pump that delivers the correct fuel
tank drained and filled with the correct fuel
type for the vehicle's engine (see a reminder
before starting the engine.
Travelling abroad
label on the inside of the filler flap).
As Diesel fuel pump nozzles may be
different in other countries, the presence
Misfuel prevention (Diesel)
of the misfuel prevention device may make
(Depending on country of sale.)
refuelling impossible.
This mechanical device prevents filling the tank
Before travelling abroad, it is advisable to
of a Diesel vehicle with petrol.
check with a PEUGEOT dealer if the vehicle
Located in the filler neck, the misfuel prevention
is suitable for the distribution equipment of the
device is visible when the filler cap is removed.
countries visited.
► Turn the filler cap to the left, remove it
Operation
and place it on its support on the filler flap
(depending on version).
Rechargeable hybrid
► Insert the filler nozzle and push it in as far as
system
possible before starting to refuel (to minimise the
risk of splashing).
Electrical system
► Fill the tank.
Do not continue past the 3rd cut-off of the
The electrical circuit of the rechargeable hybrid
nozzle; as this may cause malfunctions.
system is identified by orange cables and its
► Put the filler cap back in place and turn it to
components are marked with this symbol:
the right (depending on version).
► Push the filler flap to close it.
152
Practical information
This label is intended solely for use by
High-pressure washing
7
firefighters and maintenance services in
To avoid damaging the electrical
the event of any work on the vehicle.
components, it is expressly prohibited to
No other person must touch the device shown
use high-pressure washing in the engine
on this label.
compartment or under the body.
Do not use a pressure greater than 80 bar
The rechargeable hybrid powertrain uses
In the event of an accident or impact
when washing the bodywork.
a voltage of between 240 V and 400 V.
to the vehicle’s underbody
This system may be hot both when the
In these situations, the electrical circuit or the
Never allow water or dust to enter the
ignition is on and after switching it off.
traction battery can be seriously damaged.
connector or charging nozzle - risk of
Comply with the warning messages shown
Stop as soon as it is safe to do so and switch
electrocution or fire!
on the labels, particularly inside the charging
off the ignition.
Never connect / disconnect the charging
flap.
Contact a PEUGEOT dealer or a qualified
nozzle or cable with wet hands - risk of
workshop.
electrocution!
In the event of a problem
All work on or modifications to the
In the event of exposure to a fire
vehicle’s electrical system (including the
Traction battery
Immediately exit and evacuate all
traction battery, connectors, orange cables
The Li-ion (Lithium-ion) traction battery stores
passengers from the vehicle. Never attempt
and other components visible from the interior
the electrical energy needed to propel the
to fight the fire yourself - risk of electrocution!
or exterior) is strictly prohibited - risk of
vehicle.
You must immediately contact the emergency
severe burns or potentially fatal electric shock
It is located in the boot.
services, informing them that the incident
(short-circuit/electrocution)!
The traction battery's range varies depending
involves a rechargeable hybrid vehicle.
Contact a PEUGEOT dealer or a qualified
on the type of driving, the route, the use of
workshop.
thermal comfort equipment and the ageing of its
When washing
components.
Before washing the vehicle, always
check that the charging flap is closed
The traction battery ageing depends on
correctly.
several factors, such as climatic
Never wash the vehicle while the battery is
conditions and the distance travelled.
on charge.
153
Practical information
In the event of damage to the traction
2. Indicator lamp confirming that the nozzle is
Charging cables, sockets
battery
locked into the charging connector.
and chargers
It is strictly prohibited to work on the vehicle
Fixed red: nozzle correctly positioned and
yourself.
The traction battery can be charged using
locked.
Do not touch liquids coming from the traction
several different types of cables.
Flashing red: nozzle incorrectly positioned or
battery; in the event of contact between the
The charging cable supplied with the vehicle is
locking not possible.
skin and these products, wash abundantly
compatible with the electrical installations of the
3. Charging connector
with water and contact a doctor as soon as
country of sale. If you are travelling abroad, refer
4. Light guides
possible.
to the following tables to check the compatibility
of local electrical installations with the charging
cable.
Charging flap
Contact a PEUGEOT dealer or a qualified
The charging flap is located on the rear left-hand
workshop to obtain the appropriate charging
side of the vehicle.
cable(s).
Status of light
Meaning
Identification labels on charging
guides
sockets/connectors
Fixed white
Welcome lighting when flap
Identification labels are affixed to the vehicle,
is opened
charging cable and charger to inform the user
about which device needs to be used.
Fixed blue
Deferred charging
Flashing green
Charging
Fixed green
Charging complete
Fixed red
Malfunction
In case of impact, even light, against the
1. Deferred charging activation button
charging flap, do not use it.
Do not dismantle or modify the charging
connector - risk of electrocution and/or fire!
Contact a PEUGEOT dealer or a qualified
workshop.
154
Practical information
The meaning of each identification label is as
7
follows:
Identification label
Location
Configuration
Power type/Voltage range
Charging connector (vehicle side)
TYPE 2
AC
C
< 480 Vrms
Charging socket (charger side)
TYPE 2
AC
C
< 480 Vrms
Types of charging
Cable type
Compatibility
Specifications
Mode 2 charging cable with integrated control
Conventional electrical socket A
Charge limited to a maximum of 8 A.
unit
(depending on country).
"Green'Up" type socket B.
Charge limited to a maximum of 16 A.
Identification label C on the charging connector
(vehicle side).
155
Practical information
Cable type
Compatibility
Specifications
Mode 3 charging cable
Accelerated charging unit socket A.
Charge limited to a maximum of 32 A.
Wallbox accelerated charging unit B.
Identification labels C on the charging connector
(vehicle side) and D on the socket (charger side).
The estimated charging time is indicated
Domestic charging cable (mode 2)
Control unit (mode 2)
on the instrument panel when the vehicle
It is essential to avoid damaging the
is connected. It may vary depending on
cable and to keep it intact.
various factors such as the outside
In the event of damage, do not use it and
temperature or the quality of the electricity
contact a PEUGEOT dealer or a qualified
supply.
workshop to replace it.
If the outside temperature is below -10°C, it
is recommended to connect the vehicle as
Accelerated charging unit (mode 3)
soon as possible as the charging time may
Do not dismantle or modify the
increase significantly. The traction battery
accelerated charging unit - risk of
may not charge fully.
electrocution and/or fire!
To find out how it is used, please refer to the
accelerated charging unit's user instructions.
156
Practical information
POWER
10. Immediately stop charging, by locking and
7
Green: electrical connection established;
then unlocking the vehicle using the remote
charging can begin.
control key, if the charging cable or wall
CHARGE
socket feel burning hot to the touch.
Flashing green: charging in progress or
1.
Incorrect use of this charging cable may
11. This charging cable includes components
temperature pre-conditioning activated.
result in fire, property damage and serious
liable to cause electrical arcing or sparks.
Fixed green: charging complete.
injury or death by electrocution!
Do not expose to flammable vapours.
FAULT
2.
Always use a correctly earthed power
12. Only use this charging cable with PEUGEOT
Red: fault; charging not permitted or must
socket, protected by a 30 mA residual
vehicles.
be stopped immediately. Check that everything
current device.
13. Never plug the cable into the wall socket (or
is connected correctly and that the electrical
3.
Always use an electrical socket protected
unplug it) with wet hands.
system is not faulty.
by a circuit-breaker appropriate for the
14. Do not force the connector if it is locked into
If the indicator lamp does not go off, contact a
electrical circuit’s current rating.
the vehicle.
PEUGEOT dealer or a qualified workshop.
4.
The weight of the control unit must not be
Upon plugging the charging cable into a
Control unit label - State of indicator
borne by the electrical socket, plug and
domestic socket, all of the indicator lamps come
lamps
cables.
on briefly.
5.
Never use this charging cable if it is
State of the
If no indicator lamps come on, check the
defective or in any way damaged.
indicator lamp
domestic socket's circuit-breaker:
6.
Never attempt to repair or open this
- If the circuit-breaker has tripped, contact a
charging cable. It contains no repairable
Off
professional to check that the electrical system
parts - replace the charging cable if it is
is compatible and/or carry out any necessary
damaged.
repairs.
7.
Never immerse this charging cable in water.
On
- If the circuit-breaker has not tripped, stop
8.
Never use this charging cable with an
using the charging cable and contact a
extension cable, a multi-plug socket, a
PEUGEOT dealer or a qualified workshop.
Flashing
conversion adaptor or on a damaged
Control unit label - Recommendations
electrical socket.
9.
Do not unplug the plug from the wall as a
Refer to the handbook before use.
means of stopping charging.
157
Practical information
POWER
CHARGE
FAULT
Symbol
Description
Not connected to the power supply or power is not
available from the infrastructure.
The control unit is currently performing a self-test.
(green)
(green)
(red)
Connected only to the infrastructure or to the
infrastructure and to the Electric Vehicle (EV) but
no charging in progress.
(green)
Connected to the power supply and to the Electric
Vehicle (EV).
The EV is on charge or in a temperature pre-
(green)
(green)
conditioning sequence.
Connected to the power supply and to the Electric
Vehicle (EV).
The EV is waiting for charging or the charging of
(green)
(green)
the EV is completed.
Control unit malfunction. No charging allowed.
If an error indicator reappears after a manual reset,
the control unit must be checked by a PEUGEOT
(red)
dealer before the next charge.
The control unit is in diagnostic mode.
(green)
(green)
(red)
158
Practical information
Manual reset procedure
7
The control unit can be reset by simultaneously disconnecting the charging connector and the wall socket.
Then, reconnect the wall socket first. For more information, refer to the handbook.
Lounge mode
Wearers of pacemakers or equivalent
Charging the traction
When the vehicle is connected, it is
devices should consult a doctor to
battery (Rechargeable
possible to switch on the ignition and use
enquire about any applicable precautionary
certain functions such as the audio and
measures, or contact the manufacturer of their
hybrid)
telematics system and the air conditioning
implanted electronic medical device to check that
For a full charge, follow the charging procedure
system for several hours.
it is guaranteed to operate in an environment
without interrupting it, until it stops automatically.
compliant with the ICNIRP guidelines.
Charging may be performed either immediately
If in doubt, during charging, do not remain
Vehicle immobilised for 1 to 12
(by default) or deferred.
inside or near the vehicle, near the charging
months
Deferred charging is set via the touch
cable or the charging unit, even for a short time.
Discharge the traction battery down to 2 or
screen or the MYPEUGEOT APP
3 bars on the charge level indicator on the
Before charging
application.
instrument panel.
Depending on the context:
When the vehicle is connected, the following
Do not connect the charging cable.
► Have a professional check that the
information is displayed on the instrument panel:
Always park the vehicle in a place with
electrical system to be used complies with
- Traction battery charge status (%).
temperatures between -10°C and 30°C
applicable standards and is compatible with
- Remaining range (miles or km).
(parking in a place with extreme temperatures
the vehicle.
- Estimated charging time (calculation may take
can damage the traction battery).
► Have a professional electrician install
a few seconds).
Refer to the Accessory battery
a dedicated domestic power socket or
- Charging speed (miles or km gained per hour).
(Rechargeable hybrid) section for the
accelerated charging unit (Wallbox)
After the instrument panel has been put into
battery disconnection procedure.
compatible with the vehicle.
standby mode, this information can be displayed
Use the charging cable supplied with the
again by unlocking the vehicle or opening a door.
vehicle.
Precautions
It is also possible to monitor the charging
For more information, contact a PEUGEOT
Rechargeable hybrid vehicles have
progress using the MYPEUGEOT APP
dealer or a qualified workshop.
been developed in accordance with the
application.
recommendations for maximum electromagnetic
For more information on Remote functions,
(During charging)
field limits established by the ICNIRP
refer to the corresponding section.
As a safety measure, the engine will
(International Commission on Non-Ionizing
not start if the charging cable is plugged into
Radiation Protection - 1998 Guidelines).
159
Practical information
the connector on the vehicle. A warning is
Domestic charging (mode 2)
Accelerated charging (mode 3)
displayed on the instrument panel.
While charging is in progress, unlocking the
vehicle will cause the charging to stop.
If no action is taken on one of the openings
(door or boot) or on the charging nozzle, the
vehicle will lock again after 30 seconds and
charging will resume automatically.
Never work under the bonnet:
► Follow the accelerated charging unit
- Some areas remain very hot, even an hour
(Wallbox) user instructions.
after charging ends - risk of burns!
► Remove the protective cover from the
- The fan may start at any time - risk of cuts
charging nozzle.
or strangulation!
► Insert the nozzle into the vehicle's charging
connector.
After charging
► First, connect the charging cable from the
The start of charging is confirmed by the flashing
Check that the charging flap is closed.
control unit to the domestic socket.
of the green light guides in the flap.
Do not leave the cable connected to the
When the connection is made, all of the indicator
If this is not the case, charging has not
domestic power socket - risk of short-circuit
lamps on the control unit light up, then only the
started; restart the procedure ensuring that all
or electrocution in the event of contact with or
POWER indicator lamp remains on in green.
connections are properly established.
immersion in water!
► Remove the protective cover from the
The red indicator lamp in the flap comes on to
charging nozzle.
indicate that the nozzle is locked.
► Insert the nozzle into the vehicle's charging
Charging procedure
Disconnection
connector.
The start of charging is confirmed by the flashing
Connection
of the green light guides in the flap and the
► Before charging, check that the gear selector
flashing of the CHARGE indicator lamp in green
is in mode P and the ignition is off, otherwise
on the control unit.
charging is impossible.
If this is not the case, charging has not started;
► Press on the rear of the charging flap to open
restart the procedure, ensuring that all of the
Before disconnecting the nozzle from the
it and check that there are no foreign bodies on
connections are properly established.
charging connector:
the vehicle's charging connector.
The red indicator lamp in the flap comes on to
► If the vehicle is locked, unlock it.
The light guides in the flap come on white.
indicate that the nozzle is locked.
160
Practical information
► If the vehicle is unlocked, lock it and then
Deferred charging
Use genuine towing devices and wiring
7
unlock it.
harnesses approved by PEUGEOT. We
Settings
recommend having them fitted by a
If selective unlocking of the doors is
► In the Energy touch screen
PEUGEOT dealer or a qualified workshop.
activated, press the unlocking button on
application, select the Charging tab.
If not fitted by a PEUGEOT dealer, they must
the remote control twice to disconnect the
► Set the charging start time.
still be fitted in accordance with the vehicle
nozzle.
► Press OK.
manufacturer's instructions.
The setting is saved in the system.
Important: if the vehicle has a motorised
The red indicator lamp in the flap goes out to
You can also programme the deferred
tailgate and Hands-Free Tailgate Access
confirm that the nozzle is unlocked.
charging function using a smartphone, via
function, and a towing device has been fitted
► Within 30 seconds, remove the charging
the MYPEUGEOT APP application.
outside the PEUGEOT dealer network, it
nozzle.
For more information on Remote functions,
is essential to visit a PEUGEOT dealer or
Domestic charging (mode 2)
refer to the corresponding section.
a qualified workshop to have the detection
The end of charging is confirmed when the
Activation
system recalibrated - risk of malfunction of the
green CHARGE indicator lamp on the control
Hands-Free Tailgate Access function.
unit comes on fixed and the green light guides in
► Connect the vehicle to the desired charging
Certain driving or manoeuvring aid functions
the flap come on fixed.
equipment.
are automatically deactivated while an
► After disconnection, replace the protective
► Press this button in the flap within one
approved towing system is in use.
cover over the nozzle and close the charging
minute to activate deferred charging
For more information about driving with a
flap.
(confirmed by the light guides coming on in
towing device fitted to a trailer and associated
► Disconnect the control unit's charging cable
blue).
with the Trailer stability assist, refer to the
from the domestic socket.
corresponding section.
Accelerated charging (mode 3)
Towing device
The end of charging is confirmed by the
Load distribution
Comply with the maximum authorised
accelerated charging unit (Wallbox) and when
► Distribute the load in the trailer so that the
towable weight, as indicated on your
the green light guides in the flap come on fixed.
heaviest items are as close as possible to the
vehicle's registration certificate, on the
► After disconnection, replace the nozzle on to
axle, and the nose weight approaches the
manufacturer's label and in the Technical
the charging unit and close the charging flap.
maximum permitted without exceeding it.
data section of this guide.
Air density decreases with altitude, thus reducing
engine performance. The maximum towable load
must be reduced by 10% per 1,000 metres of
altitude.
161
Practical information
If using accessories attached to the
Towing device with quickly
towing device (e.g. bicycle carriers, tow
boxes):
detachable towball
- Comply with the maximum authorised nose
weight.
Presentation
- Do not transport more than 4 conventional
No tools are required to install or remove this
bicycles or 2 electric bicycles.
genuine towing device.
A. Locked position (green mark opposite the
When loading bicycles onto a bicycle carrier
white mark); the wheel is in contact with the
on a towball, be sure to place the heaviest
towball (no gap).
bicycles as close as possible to the vehicle.
B. Unlocked position (red mark opposite the
white mark); the wheel is no longer in contact
Observe the legislation in force in the
with the towball (gap of around 5 mm).
country where you are driving.
To ensure complete safety while driving
Vehicle equipped with motorised
with a Towing device, refer to the
tailgate with hands-free function
corresponding section.
(Hands-Free Tailgate Access)
To avoid unintentionally opening the
Before each use
motorised tailgate when operating the towing
1.
Carrier
Verify that the towball is correctly fitted,
device:
2.
Protective plug
checking the follow points:
- Deactivate this function in advance in the
3.
Connection socket
- The green mark on the wheel is aligned
vehicle's configuration application.
4.
Safety eye
with the white mark on the towball.
- Or remove the electronic key from the
5.
Detachable towball
- The wheel is in contact with the towball
recognition zone, with the tailgate closed.
6.
Locking/unlocking wheel
(position A).
7.
Security key lock
- The security key lock is closed and the
8.
Label to note the key references
key removed; the wheel can no longer be
operated.
- The towball must not be able to move in
its carrier; test by attempting to shake it with
your hand.
If the towball is not locked, the trailer can
become detached - risk of an accident!
162
Practical information
During use
Fitting the towball
7
Never release the locking system with a
trailer or load carrier on the towball.
Never exceed the maximum authorised
weight for the vehicle - the Gross Train
Weight or GTW.
Always comply with the maximum authorised
load on the towing device: if it is exceeded,
this device may become detached from the
vehicle - risk of an accident!
► Check that the mechanism has correctly
Before driving, check the headlamp height
locked into place and that the green mark on
adjustment and check that the lamps on the
the wheel is aligned with the white mark on the
trailer operate correctly.
towball (position A).
For more information on Headlamp height
► Below the rear bumper, remove the protective
► Close the lock 7 using the key.
adjustment, refer to the corresponding
plug 2 from the carrier 1.
► Remove the key. The key cannot be removed
section.
► Insert the end of the towball 5 into the carrier
while the lock is open.
1 and push it upwards; it will lock into position
► Lower the cap to protect the lock.
After use
automatically.
When travelling without a trailer or
load carrier, remove the towball and fit the
protective plug into the carrier, to provide
clear visibility of the number plate and/or its
lighting.
► The wheel 6 rotates a quarter turn anti-
clockwise; take care to keep your hands clear!
163
Practical information
Removing the towball
a clockwise direction until it stops; do not release
the wheel.
► Grasp the trailer's plug, perform a quarter
turn and pull to disconnect it from the connection
socket 3 on the carrier.
► Extract the towball from the base of its
► Detach the trailer's safety cable from the
carrier 1.
► Remove the protective cover from the
► Release the wheel; it automatically locks
safety eye 4 on the carrier.
towball.
in the unlocked position and the red mark on
► Unhitch the trailer from the towball.
► Attach the trailer to the towball.
the wheel is in line with the white mark on the
► Replace the protective cover over the towball.
► Attach the cable on the trailer to the safety
towball (position B).
eye 4 on the carrier.
► Insert the trailer plug and rotate it by a
quarter turn to connect it to the connection
socket 3 on the carrier.
► Lift the cap to access the lock.
► Insert the key into the lock 7.
► Open the lock using the key.
► Hold the towball 5 firmly in one hand; using
the other hand, pull and turn the wheel 6 fully in
164
Practical information
► Replace the protective plug 2 into the
not exceeding 40 cm (except bicycle carrier):
Fitting on longitudinal bars
7
carrier 1.
80 kg.
(SW)
► Stow the towball in its bag to protect it from
As this value may change, please verify the
knocks and dirt.
maximum load quoted in the guide supplied
with the roof bars.
Maintenance
If the height exceeds 40 cm, adapt the speed
Correct operation is only possible if the towball
of the vehicle to the profile of the road to
and its carrier are kept clean.
avoid damaging the roof bars and the fixings
Before cleaning the vehicle with a high-pressure
on the vehicle.
jet wash, the towball must be removed and the
Be sure to refer to national legislation in order
protective plug fitted to the carrier.
to comply with the regulations for transporting
The transverse bars must be fixed at the
objects that are longer than the vehicle.
Work on the towing device
markings located on the longitudinal bars.
Contact a PEUGEOT dealer or a
Recommendations
qualified workshop.
Direct fitting on roof
Distribute the load uniformly, taking care
to avoid overloading one of the sides.
Arrange the heaviest part of the load as close
Roof bars
as possible to the roof.
Secure the load firmly.
As a safety measure and to avoid
Drive gently: the vehicle will be more
damaging the roof, it is essential to use
susceptible to the effects of side winds and its
transverse roof bars approved for your
stability may be affected.
vehicle.
Regularly check the security and tight
Observe the instructions on fitting and use
fastening of the roof bars, at least before each
contained in the guide supplied with the roof
trip.
bars.
Remove the roof bars once they are no longer
needed.
The transverse bars must only be fixed at the
Maximum load distributed over the
four anchorage points located on the roof frame.
transverse roof bars, for a loading height
These points are concealed by the vehicle doors
when the doors are closed.
The roof bar fixings have a stud which must be
inserted into the opening of each anchorage
point.
165
Practical information
It is essential to remove them when:
Fitting
- the outside temperature exceeds
10°C.
- recovery is in progress.
- the speed is above 75 mph (120 km/h).
First installation
The type of grille depends on the vehicle version.
Sunroof
The lower screens are suitable for all versions.
Do not operate the sunroof when using
Lower/upper screens
The upper and centre screens can be adapted
roof bars - risk of major damage!
► Offer up one of the lower screens on the
according to the vehicle version.
corresponding side of the lower bumper grille,
aligning it around the number plate holder.
Very cold climate screens
► Insert the fixing lugs into the bumper until
they are all properly seated.
(Depending on country of sale)
► Check that the unit is firmly held by pressing
Only available for Diesel vehicles.
around the edges.
This removable device prevents the
Repeat the same steps for the other lower
accumulation of snow around the radiator
screen, then for the upper screens in the upper
cooling fan.
bumper grille, aligning them with the top of the
It consists of two elements for the upper part of
grille.
the front grille, a central element and two other
elements for the lower part.
Centre screen
► Offer up the centre screen below the brand
In case of difficulty with installation/
badge.
removal
► Insert the fixing lugs into the bumper until
Contact a PEUGEOT dealer or a qualified
they are all properly seated.
workshop.
It is necessary to remove the fixings:
► Check that the unit is firmly held by pressing
- Marked 2 for all versions except GT.
around the edges.
Before any operation, ensure that the
- Marked 1 for all GT versions.
engine is off and the cooling fan has
► To remove the corresponding fixings, use a
stopped.
cutter-type tool, following the groove set into the
inner face of the screen.
166
Practical information
Removing
► Press on the upper fixing lugs to release
Installation tips
7
them from the grille.
► To fit the snow chains during a journey, stop
► Pull towards you to guide the unclipping of
the vehicle on a flat surface at the side of the
the unit.
road.
► Apply the parking brake and position any
Snow chains
wheel chocks under the wheels to prevent
movement of the vehicle.
In wintry conditions, snow chains improve
► Fit the snow chains following the instructions
traction as well as the behaviour of the vehicle
provided by the manufacturer.
For the lower screen
when braking.
► Move off gently and drive for a few moments,
► Insert a finger in the lower outside corner of
Snow chains must be fitted only to the
without exceeding 31 mph (50 km/h).
the lower screen.
front wheels. They must never be fitted to
► Stop the vehicle and check that the snow
► Pull towards you to guide the unclipping of
"space-saver" type spare wheels.
chains are correctly tightened.
the unit.
It is strongly recommended that you
Observe the legislation in force in your
practise fitting the snow chains on a level
country relating to the use of snow
and dry surface before setting off.
chains and maximum authorised speeds.
Only use chains that have been designed for the
Avoid driving with snow chains on roads
type of wheel fitted to your vehicle:
that have been cleared of snow to avoid
For the upper screen
damaging the vehicle's tyres and the road
► Press on the lower fixing lugs to release them
Original tyre size
Maximum link size
surface. If the vehicle is fitted with alloy
from the grille.
205/55 R16
9 mm
wheels, check that no part of the chain or its
► Gently tilt the upper screen downwards.
fixings is in contact with the wheel rim.
► Pull towards you to guide the unclipping of
205/60 R16
9 mm
the unit.
215/50 R17
9 mm
225/45 R17
9 mm
Energy economy mode
225/40 R18
Polaire PSGB 60
This system manages the duration of use of
certain functions, in order to conserve a sufficient
For more information, contact a PEUGEOT
level of charge in the battery with the ignition off.
For the centre screen
dealer or a qualified workshop.
After switching off the engine, you can still
use functions such as the audio and telematic
167
Practical information
system, the wipers and the dipped beam
indicator lamp is off on the instrument panel
Load reduction mode
headlamps or courtesy lamps, for a combined
and wait 4 minutes - risk of serious injury!
This system manages the use of certain
duration of approximately 40 minutes.
functions according to the level of charge
Selecting the mode
remaining in the battery.
When the vehicle is being driven, the load
A confirmation message is displayed when
reduction function temporarily deactivates certain
energy economy mode is entered, and the active
functions, such as the air conditioning and the
functions are placed on standby.
heated rear screen.
The location of the interior bonnet
If a telephone call is in progress at the
The deactivated functions are reactivated
release lever prevents the bonnet being
time, it will be maintained for around 10
automatically as soon as conditions permit.
opened when the left-hand front door is
minutes via the audio system’s hands-free
closed.
system.
Bonnet
When the engine is hot, handle the
Exiting the mode
Stop & Start
exterior safety catch and the bonnet stay
Before doing anything under the bonnet,
with care (risk of burns), using the protected
These functions are automatically reactivated the
you must switch off the ignition to avoid any
area.
next time the vehicle is used.
risk of the engine restarting automatically.
When the bonnet is open, take care not to
To restore the use of these functions
Take care with objects or clothing that could
damage the safety catch.
immediately, start the engine and let it run:
be caught in the blades of the cooling fan
Do not open the bonnet under very windy
- For less than 10 minutes, to use the
or in certain moving components - risk of
conditions.
equipment for approximately 5 minutes.
strangulation and serious injury!
- For more than 10 minutes, to use the
equipment for approximately 30 minutes.
Cooling of the engine when stopped
Let the engine run for the specified duration to
The engine cooling fan may start after
ensure that the battery charge is sufficient.
the engine has been switched off.
To recharge the battery, avoid repeatedly or
Take care with objects or clothing that
continuously restarting the engine.
could be caught in the blades of the fan!
Rechargeable hybrid vehicles
A flat battery prevents the engine from
Before any work is carried out under the
starting.
bonnet, it is essential to switch off the ignition
For more information on the 12 V battery,
and disconnect the charging connector nozzle
refer to the corresponding section.
if it is connected, check that the READY
168
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст