Peugeot 308 (2022 year). Manual in english — page 7
Driving
- Stationary vehicles (e.g. traffic jams,
- Excessively sharp deceleration by the vehicle
If the vehicle has undergone any of the
6
breakdown).
in front of you.
following modifications, do not use the
system:
- Carrying long objects on roof bars.
- Towing.
- Front end of the vehicle modified (for
example by adding long-range headlamps or
painting the front bumper).
- Vehicles crossing your lane.
- When a vehicle cuts in sharply between your
- Obstructed radar.
- Vehicles driving in the opposite direction.
vehicle and the one in front.
Situations where the driver must suspend the
Some vehicles on the road may be
Malfunction
system:
poorly perceived or interpreted by the
In the event of a malfunction, dashes are
camera and/or the radar (e.g. truck), which
displayed (orange) instead of the speed setting.
can lead to an incorrect evaluation of
This warning lamp comes on,
distances and result in inappropriate
accompanied by a message and an
acceleration or braking of the vehicle.
audible signal, to confirm the malfunction.
Have it checked by a PEUGEOT dealer or a
Pay particular attention:
qualified workshop.
- When motorcycles are present and
- Vehicles in a tight bend.
when there are vehicles staggered across the
Lane positioning assist
- When approaching a roundabout.
traffic lane.
- When entering a tunnel or crossing a
For more information, refer to the
bridge.
General recommendations on the use
of driving and manoeuvring aids.
If any of the following malfunctions
occurs, do not use the system:
- Following an impact on the windscreen
- When following a narrow vehicle.
close to the camera or on the front bumper.
Reactivate the system when conditions allow.
- If a brake lamp is not working.
Situations in which the driver is prompted to
immediately resume control:
127
Driving
The system identifies the edges of the traffic lane
The system status is saved when the
Pausing/Suspending the
and steers the vehicle to keep it inside this lane
ignition is switched off.
system
and maintain the lateral position chosen by the
driver.
The driver must act promptly if they
Operating conditions
To do this, the system uses a camera placed on
believe that the traffic conditions or the
the upper part of the windscreen.
- Adaptive cruise control active.
state of the road surface require their
This system is particularly suited to driving on
- ESC system operational.
intervention, by moving the steering wheel to
motorways and main roads.
- ASR system activated.
temporarily suspend system operation. Any
- No trailer detected.
action on the brake pedal that causes the
Activation/Deactivation
- No 'space-saver' spare wheel in use.
Adaptive cruise control system to be paused
- Vehicle not subject to strong lateral
The Lane positioning assist system is
will also cause the system to be paused.
acceleration.
automatically activated, after selecting Drive
- Direction indicators off upon activation of the
Assist Plus mode.
If the system detects that the driver is not
system.
For more information on the Drive Assist Plus
holding the wheel firmly enough, it
system, refer to the corresponding section.
Cruise control
triggers a series of gradual alerts and then
The selection is confirmed by the display of the
deactivates itself if there is no response from
symbols on the instrument panel, representing
The driver must hold the steering wheel properly.
the driver.
the steering wheel and the side lines.
When cruise control is activated, the symbols are
The colour of the symbols depends on the
displayed in green: with small steering inputs,
the system steers the vehicle and keeps it in the
If the function is suspended due to the
operating state of the system:
position chosen by the driver in the traffic lane.
prolonged release of the force holding
(grey)
This position is not necessarily the centre of the
the steering wheel, the system must be
One or more operating conditions is not
lane.
reactivated by pressing the ASSIST button
met; the system is paused.
You can feel the steering wheel moving.
again.
(green)
All operating conditions are met; the
At any time, the driver can change the position of
Automatic suspension
system is active.
the vehicle by intervening on the steering wheel
(orange)
and maintaining the position until the system has
Suspension of the system is accompanied by a
System malfunction.
taken it into account. If the chosen position is too
specific audible signal.
If the driver no longer wishes to use the system
off-centre, an automatic re-centering manoeuvre
- Triggering of the ESC system.
for some time, they can deactivate it by pressing
can occur. The system adjusts to the newly
- Insufficient lane detection. In this case, the
the ASSIST button again (confirmed by the
defined position.
Active lane departure warning system function
Driving aids mini-view disappearing from the
can take over, and the system will reactivate
instrument panel).
128
Driving
itself once the operating conditions are met
- Too tight a grip on the steering wheel or
pedal (suspension for as long as the pedal is
6
again.
dynamic action on the steering wheel.
depressed).
Paused by the driver
- Action on the brake pedal (resulting in a pause
- Pausing of the Adaptive cruise control system.
until cruise control is reactivated) or accelerator
- Deactivation of the ASR system.
– Travelling outside the lane limits.
Driving situations and related alerts
The tables below describe the displays associated with the main driving situations. The actual order of display of these alerts may be different.
Steering wheel-mounted
Symbols
Comments
controls
ASSIST or I I>
Cruise control paused.
Drive Assist Plus activated.
(grey)/(grey)
ASSIST or OK
Cruise control on.
Drive Assist Plus activated.
(green) /(green)
ASSIST
Drive Assist Plus activated.
Lane positioning assist operates normally (presence of steering wheel
correction).
(green)/(green)
I I>
Drive Assist Plus paused by the driver.
(grey) /(grey)
ASSIST or OK
Drive Assist Plus activated.
All the operating conditions for lane positioning assist have not been met.
(green)/(grey)
129
Driving
Steering wheel-mounted
Symbols
Comments
controls
ASSIST or I I>
Drive Assist Plus suspended.
Cruise control and lane positioning assist are suspended.
(grey)/(grey)
Messages
Driving situations
"Keep your hands on the steering wheel"
Prolonged driving without holding the steering wheel, holding it improperly or
without applying any force.
"Hold the steering wheel"
Actual or imminent loss of lane positioning assist.
"Take back control"
Simultaneous loss of cruise control and lane positioning assist.
- Windscreen area in front of the camera
- Road with low grip (risk of aquaplaning,
Operating limits
dirty, misted up, frost-covered, snow-covered,
snow, ice).
The system may issue an alert when the
damaged or covered by a sticker.
- Road works and toll areas.
vehicle is travelling on a long, straight
- Lane markings eroded, partially hidden (snow,
- Driving on racing circuits.
road with smooth road surface even if the
mud) or multiple (roadworks, surface joints).
- Driving on a rolling road.
driver thinks they are holding the steering
- Travelling in a tight bend.
wheel correctly.
- Winding roads.
Malfunction
- Road surface repairs.
The system may not operate or may produce
In the event of a malfunction, the
Risk of undesirable operation
unsuitable corrections to the steering in the
Service warning lamp comes on
following situations:
The system should be deactivated in the
and this (orange) symbol appears on the
- Wearing thick gloves (with Drive Assist 2.0).
following situations:
instrument panel, accompanied by the display of
- Poor visibility (insufficient road lighting,
- When changing a wheel or working near a
a message and an audible signal.
snowfall, rain, fog).
wheel.
Have it checked by a PEUGEOT dealer or a
- Dazzle (headlamps of an oncoming vehicle,
- Towing or with a bicycle carrier on a towing
qualified workshop.
low sun, reflections on a wet road surface,
device, especially with trailer not plugged in or
leaving a tunnel, alternating light and shade).
not approved.
– Adverse weather conditions.
130
Driving
- Drive Assist 2.0 activated.
To do this, it uses the camera located at the top
Speed adjustment during
6
- Vehicle speed between 43 and 112 mph (70
of the windscreen, the radar located at the front
cornering
and 180 km/h).
and the four angle radars fitted in the bumpers.
(with Drive Assist 2.0)
The steering wheel is equipped with a
Operation
hands-on detection system to avoid
For more information, refer to the
The vehicle is moving at the
distraction on the part of the driver.
General recommendations on the use
speed setting and is monitoring
For more information on the Hands-on
of driving and manoeuvring aids and the
bends.
detection, refer to the corresponding section.
Cruise control - particular
recommendations.
The system gradually decreases
The system cannot in any circumstances
In addition to Adaptive cruise control with
the speed in the bend to
replace the need for vigilance on the part
Stop&Go function and Lane positioning assist,
negotiate it comfortably.
of the driver. The driver remains responsible
this system regulates the speed of the vehicle
for their driving by monitoring their
within its traffic lane in bends.
surroundings and keeping their hands on the
Temporary driver intervention
It adapts the speed, with or without target
steering wheel.
vehicle, in certain bends on motorways or main
If the driver believes that the speed is too slow or
The driver must act promptly if they believe
roads.
too fast, they can act on the pedals.
that the traffic conditions or the state of the
The speed is only adjusted if the vehicle speed is
Pressing the brake pedal deactivates Drive
road surface require their intervention, by
not compatible with the angle of the bend.
Assist 2.0, while pressing the accelerator pedal
moving the steering wheel to temporarily
The reduction in speed on a bend is adapted
temporarily suspends it.
suspend system operation.
to the situation in order to ensure the bend is
Any intervention on the brake pedal or the
navigated comfortably.
accelerator pedal that causes the adaptive
Semi-automatic lane
In the presence of a target vehicle, it also
cruise control to be paused or suspended will
maintains the inter-vehicle distance.
changing
also cause the system to deactivate.
This system does not manage bends that
(with Drive Assist 2.0)
are too tight (e.g. hairpin bends).
Selecting the system
For more information, refer to the
Two options:
General recommendations on the use
- Either when the vehicle is already driving on
Operating conditions
of driving and manoeuvring aids.
an eligible road, the driver selects the system by
- Eligible roads: roads with separate
activating the Drive Assist 2.0 system.
This system assists the driver in changing lanes.
carriageways with prohibited access for
pedestrians and cyclists.
131
Driving
- Or when the driver is already using Drive
- The line separating the lanes must be clear
The message "Stay alert" is displayed as a
Assist Plus, the vehicle suggests selecting the
enough to be identified by the system.
reminder that the driver is still responsible for the
system upon arriving at an eligible road by
- The position and speed of other vehicles must
manoeuvre.
pressing the OK button.
enable the system to safely change lanes.
- Drive Assist 2.0 activated.
Activation/Deactivation
- Lane positioning assist activated.
- Vehicle speed between 43 and 112 mph (70
and 180 km/h).
The system then proceeds with the vehicle’s
lane change.
Authorised lane change
Once the manoeuvre has been carried out, the
request
system is automatically deactivated and the lane
When operating the direction indicator, if the
positioning assist takes over.
necessary conditions are met, the message
If the direction indicator has been set beyond the
"OK?" is displayed on the instrument panel,
point of resistance, the driver must pull it back.
accompanied by an audible signal.
► Activate the direction indicator on the side
The driver must hold the steering wheel
corresponding to the lane change, whether or
correctly.
not passing the resistance point of the lighting
As soon as the semi-automatic lane change
control stalk.
begins, the system directs the vehicle to the
The driver can regain control of the vehicle at
target lane by small actions on the steering to
any time:
position it in the destination lane.
- by deactivating the direction indicator if the
You can feel the steering wheel moving.
vehicle has not yet crossed the line.
- by firmly holding the steering wheel.
Interrupting the lane change
- by acting on the pedals.
It is possible that while changing lane, the
For more information on the Direction
necessary conditions for the operation of the
indicators, refer to the corresponding section.
system may no longer be met.
Operating conditions
► After checking the surroundings, press
2-OK to confirm the start of the lane change
- Eligible roads: roads with separate
manoeuvre.
carriageways with prohibited access for
pedestrians and cyclists.
132
Driving
If this occurs before one of the wheels has
If this occurs when the lane change has
instrument panel, accompanied by an audible
6
crossed the line separating the two lanes, the
started, the system prompts the driver to
signal.
system automatically returns the vehicle to
immediately retake control of the vehicle
its original lane (confirmed by the display of
(confirmed by the display of a message on the
a manoeuvre cancellation message on the
instrument panel and an audible signal), and the
instrument panel and an audible signal). The
system is automatically deactivated.
system is then automatically deactivated.
The system keeps the vehicle in the original
Refused lane change
lane. The system is deactivated and the semi-
request
automatic lane change is not carried out.
When pressing 2-OK, if the necessary conditions
are not met, the lines appear in orange on the
Messages and alerts
The actual order of display of the messages or alerts may be different.
Display
Comments
System awaiting selection.
(grey)/(continuous grey)/(grey)
System selection request.
(grey)/(continuous green)/(green)
133
Driving
Display
Comments
System selected.
(green)/(continuous green)/(green)
Confirmation request for a lane change manoeuvre.
(green)/(broken green)/(green)
Lane change manoeuvre in progress.
(green)/(broken green)/(green)
Refused lane change manoeuvre.
(green)/(continuous orange)/(green)
(orange)
(blue)
The system cannot manage the current driving
“Lane change interrupted: stay in the
"Lane change cancelled"
situation.
lane”
Continuation of Lane positioning assist and
Brake, accelerate or use the steering wheel,
Adaptive cruise control.
Operating limits
depending on the context.
(red)
The system may not work in the following
"Take back control"
situations:
134
Driving
- Wearing thick gloves.
deactivates itself if there is no response from
The speed will be reduced by a
6
- Poor visibility (insufficient road lighting,
the driver.
maximum of 16 mph (25 km/h) for
snowfall, rain, fog).
versions with camera only, or by a maximum
- Dazzle (headlamps of an oncoming vehicle,
of 31 mph (50 km/h) for versions with camera
Malfunction
low sun, reflections on a wet road surface,
and radar.
leaving a tunnel, alternating light and shade).
In the event of a malfunction, this warning
- Windscreen area in front of the camera
lamp lights up on the instrument panel,
The system also takes motorcyclists and
dirty, misted up, frost-covered, snow-covered,
accompanied by the display of a message and
animals into account; however, animals
damaged or covered by a sticker.
an audible signal.
below 0.5 m tall and objects on the road are
- Lane markings eroded, partially hidden (snow,
Have it checked by a PEUGEOT dealer or a
not necessarily detected.
mud) or multiple (roadworks, surface joints).
qualified workshop.
- Travelling in a tight bend.
This system is comprised of three functions:
- Winding roads.
- Collision Risk Alert.
Active Safety Brake with
- Road surface repairs.
- Intelligent emergency braking assistance
Collision Risk Alert and
(iEBA).
The system must not be activated in the
- Active Safety Brake (automatic emergency
following situations:
Intelligent emergency
braking).
- When changing a wheel or working near a
braking assistance
wheel.
- Towing or with a bicycle carrier on a towing
For more information, refer to the
device, especially with trailer not plugged in or
General recommendations on the use
not approved.
of driving and manoeuvring aids.
- Adverse weather conditions.
- Road with low grip (risk of aquaplaning,
snow, ice).
- Road works and toll areas.
The vehicle has a multifunction camera located
- Driving on racing circuits.
This system:
at the top of the windscreen and, depending on
- Driving on a rolling road.
- warns the driver that their vehicle is at risk of
version, a radar located in the front bumper.
collision with the vehicle in front, a pedestrian or,
If the system detects that the driver is not
This system does not replace the need
depending on version, a cyclist.
holding the steering wheel firmly enough,
for vigilance on the part of the driver.
- reduces the vehicle's speed to avoid a
it triggers a series of gradual alerts and then
This system is designed to assist the driver
collision or limit its severity.
and improve road safety.
135
Driving
It is the driver's responsibility to continuously
- Before using an automatic car wash, with the
Collision Risk Alert
monitor traffic conditions in accordance with
engine running.
This function warns the driver that their vehicle
applicable driving regulations.
- When changing a wheel, working near a wheel
is at risk of a collision with the vehicle in front, or
or inside the engine compartment.
with a pedestrian or cyclist present in their traffic
As soon as the system detects a
- Before placing the vehicle on a rolling road in
lane.
potential obstacle, it prepares the braking
a workshop.
circuit in case automatic braking is needed.
- Towed vehicle, engine running.
Modifying the alert trigger threshold
This may cause a slight noise and a slight
- Following an impact to the windscreen close to
The trigger threshold determines the sensitivity
sensation of deceleration.
the detection camera.
with which the function warns of the risk of
The system is automatically deactivated
collision.
when the use of certain types of
It is configured in the ADAS touch screen
Deactivation/Activation
"space-saver" spare wheel (smaller diameter)
application.
By default, the system is automatically activated
is detected, or if a fault with the brake pedal
► Select one of the 3 preset
at every engine start.
switch or at least two brake lamps is detected.
thresholds: "Far", "Medium" or "Near".
It is configured in the ADAS touch screen
The selected threshold is memorised when the
application.
ignition is switched off.
It can be dangerous to drive if the brake
Deactivation of the system is signalled by
lamps are not in perfect working order.
the illumination of this warning lamp,
Operation
accompanied by the display of a message.
Depending on the degree of risk of collision
The driver must not overload the vehicle
detected by the system and the alert trigger
Operating conditions and
(keep within the GVW and GTW limits,
threshold chosen by the driver, several different
and load height limits for roof bars).
limits
levels of alert may be triggered and displayed on
Vehicle moving forward.
the instrument panel.
It is possible that warnings are not given,
ESC system operational.
The system takes account of the vehicle
are given too late or seem unjustified.
ASR system activated.
dynamics, the speed of your vehicle and the one
The driver must always stay in control of the
Seat belts fastened for all passengers.
in front, the environmental conditions and the
vehicle and be prepared to react at any time
Stabilised speed on roads with few bends.
operation of the vehicle (actions on the pedals,
to avoid an accident.
In the following cases, deactivating the system
steering wheel, etc.) to trigger the alert at the
via the driving aids configuration application is
most relevant moment.
advised:
Following an impact, the system is
(orange)
– Carrying long objects on roof bars.
automatically deactivated.
Level 1: visual alert only, warning you
Have it checked by a PEUGEOT dealer or a
that the vehicle in front is very close.
qualified workshop.
136
Driving
The message "Vehicle close" is displayed.
Active Safety Brake
Operation
6
(red)
The system operates subject to the following
Level 2: visual and audible alert, warning
conditions:
you that a collision is imminent.
- The vehicle's speed does not exceed 37 mph
The message "Brake!" is displayed.
(60 km/h) when a pedestrian is detected.
Level 3: in some cases, a vibration alert in the
- The vehicle's speed does not exceed 50 mph
form of micro-braking can be given, confirming
(80 km/h) when a stationary vehicle or a cyclist
the risk of collision.
is detected.
- The vehicle's speed is between 6 mph and
Where the speed of your vehicle is too
53 mph (10 km/h and 85 km/h) (versions with
high approaching another vehicle, the
camera only) or 87 mph (140 km/h) (versions
first level of alert may not be displayed: the
with camera and radar) when a moving vehicle
level 2 alert may be displayed directly.
is detected.
Important: the level 1 alert is not displayed
This warning lamp flashes (for
when there is a stationary obstacle or
approximately 10 seconds) as soon as
when the "Near" trigger threshold has been
the function applies the vehicle’s brakes.
selected.
With an automatic gearbox, in the event of
automatic emergency braking bringing the
This function, also called automatic emergency
Intelligent emergency
vehicle to a complete stop, keep the brake pedal
braking, intervenes following the alerts if the
depressed to prevent the vehicle from moving
braking assistance (iEBA)
driver does not react quickly enough and does
off again.
This function supplements braking in the event
not operate the vehicle's brakes.
With a manual gearbox, in the event of automatic
that the driver brakes, but not enough to avoid a
The system aims to reduce the speed of impact
emergency braking bringing the vehicle to a
collision.
or avoid a collision where the driver fails to react.
complete stop, the engine may stall.
This assistance will only be provided if the driver
The speed will be reduced by a
presses the brake pedal.
The driver can maintain control of the
maximum of 16 mph (25 km/h) for
vehicle at any time by firmly turning the
versions with camera only, or by a maximum
steering wheel and/or firmly depressing the
of 31 mph (50 km/h) for versions with camera
accelerator pedal.
and radar.
137
Driving
The brake pedal may vibrate slightly
Intersection with pedestrians
belt is not fastened (depending on version). The
while the function is operating.
automatic braking system is deactivated until the
If the vehicle comes to a complete stop,
seat belts are fastened.
automatic braking is maintained for 1 to 2
seconds.
Distraction detection
Special cases
For more information, refer to the
General recommendations on the use
Intersection with another vehicle
of driving and manoeuvring aids.
The function comprises the "Driver Attention
The system operates when the vehicle is turning
Warning" system combined with the "Driver
left or right and detects pedestrians crossing if:
Attention Warning by Camera" system.
- The pedestrians are crossing in front of the
These systems are in no way designed
vehicle.
to keep the driver awake or to prevent
- The speed of the vehicle is between 3 and 50
the driver from falling asleep at the wheel.
mph (5 and 80 km/h).
It is the driver’s responsibility to stop if feeling
tired.
Malfunction
Take a break if you are feeling tired or at least
The system operates when the vehicle is turning
In the event of a malfunction, this warning
every 2 hours.
and detects another vehicle approaching from
lamp lights up on the instrument panel,
the opposite direction if:
accompanied by the display of a message and
- The vehicle is about to cross the path of
an audible signal.
Activation/Deactivation
another vehicle.
Have it checked by a PEUGEOT dealer or a
By default, the function is automatically activated
- The corresponding direction indicator is
qualified workshop.
at every engine start.
activated in advance.
If these warning lamps come on
The settings are changed via the ADAS
- The speed of the vehicle is between 3 and 12
after the engine has been switched
touch screen application.
mph (5 and 20 km/h).
off and then restarted, contact a PEUGEOT
dealer or a qualified workshop to have the
Driver Attention Warning
system checked.
The system triggers an alert when it
These warning lamps light up on
detects that the driver has not taken a
the instrument panel to indicate
that the driver's and/or front passenger's seat
138
Driving
break after two hours of driving at a speed above
Driver Attention Warning by
Active lane departure
6
43 mph (70 km/h).
Camera
warning system
This alert is issued via the display of a message
encouraging the driver to take a break,
For more information, refer to the
accompanied by an audible signal.
General recommendations on the use
If the driver does not follow this advice, the alert
of driving and manoeuvring aids.
is repeated hourly until the vehicle is stopped.
The system resets itself if one of the following
The system corrects the vehicle's trajectory by
conditions is met:
alerting the driver as soon as it detects a risk of
- With the engine running, the vehicle has been
involuntary lane departure or crossing of a verge
stationary for more than 15 minutes.
or hard shoulder (depending on version).
- The ignition has been switched off for a few
To do this, the system uses a camera, placed on
minutes.
the upper part of the windscreen, identifying the
- The driver's seat belt is unfastened and their
lane markings on the ground and the side of the
door is opened.
The system assesses the driver's level of
road (depending on version).
alertness, fatigue and distraction by
As soon as the speed of the vehicle
This system is particularly useful on
identifying trajectory changes in relation to the
drops below 43 mph (70 km/h), the
motorways and main roads.
lane markings.
system goes into standby.
To do this, the system uses a camera, placed on
Driving time starts being counted again once
the upper part of the windscreen.
the speed reaches above 43 mph (70 km/h).
This system is particularly suited to fast roads
(speed higher than 43 mph (70 km/h)).
At a first alert level, the driver is warned by the
message "Be vigilant!", accompanied by an
Operating conditions
audible signal.
- Vehicle speed between 43 and 112 mph (70
After three first-level alerts, the system triggers
and 180 km/h).
a further alert with the message "Dangerous
- Road marked with a central dividing line.
driving: take a break", accompanied by a more
- Steering wheel held with both hands.
pronounced audible signal.
- Direction indicators off upon activation of the
system.
- ESC system activated and operational.
139
Driving
The system helps the driver only if there
Operation
The driver can prevent the correction by
is a risk of the vehicle unintentionally
firmly holding the steering wheel
As soon as the system identifies a risk of
wandering from the lane it is being driven in. It
(e.g. during an emergency manoeuvre).
involuntarily crossing one of the lane markings
does not manage the safe driving distance,
The correction is interrupted immediately if
detected on the ground or a lane boundary
vehicle speed or braking.
the direction indicators are operated.
(e.g. grass verge), it performs the trajectory
The driver must hold the steering wheel with
correction necessary to restore the vehicle to its
While the direction indicators are activated and
both hands so that they can maintain control
original lane.
for a few seconds after switching them off, the
when the conditions no longer allow the
The driver will notice a turning movement of the
system considers that a change of trajectory is
system to intervene (e.g. in the event that
steering wheel.
intentional and no correction is triggered during
the central dividing line marking on the road
This warning lamp flashes during
this period.
surface disappears).
trajectory correction.
Driving situations and related alerts
The table below describes the alerts and messages displayed in different driving situations.
The actual order of display of these alerts may be different.
Function status
Display
Comments
OFF
Function deactivated.
ON
None.
System active, conditions not met:
- Speed below 40 mph (65 km/h).
- No lane marking recognised.
- ESC operation triggered.
- "Sporty" driving.
ON
Automatic deactivation/standby of the function (e.g. detection of a trailer, use of the
"space-saver" type spare wheel supplied with the vehicle, failure).
ON
None.
Lane marking detected.
Speed above 40 mph (65 km/h).
140
Driving
Function status
Display
Comments
6
ON
The system corrects the trajectory on the side where the risk of line crossing is detected.
The driver's hands are on the steering wheel.
ON
If, while correcting the trajectory, the system determines that the correction will not be
enough and that a solid line will be crossed: the driver is warned that they must provide
additional trajectory adjustment.
If the steering wheel is not held properly, an audible warning sounds, accompanied by
a message, until the trajectory correction is completed or the driver has grasped the
"Hold the steering
steering wheel correctly.
wheel" or "Stay in lane"
The duration of audible warnings will increase if multiple corrections are performed
(depending on version)
in quick succession. The warning will become continuous, persisting until the driver
responds.
- Inactivity by the driver detected during
Risk of undesirable operation
Operating limits
correction.
The system should be deactivated in the
The system goes into standby automatically in
- Narrow lane detected.
following situations:
the following cases:
- ESC deactivated or operation triggered.
The following situations may interfere
- When changing a wheel or working near a
- Speed below 40 mph (65 km/h) or greater
with the operation of the system or
wheel.
than 112 mph (180 km/h).
prevent it from working:
- Towing or with a bicycle carrier on a towing
- Electrical connection to a trailer.
- Insufficient contrast between the road
device, especially with trailer not plugged in or
- Use of a"space-saver" spare wheel detected
surface and the verge or hard shoulder
not approved.
(as detection is not immediate, deactivation of
(e.g. shade).
- Road in poor condition, unstable or with very
the system is recommended).
- Lane markings worn, hidden (snow, mud)
poor grip (risk of aquaplaning, snow, ice).
- Dynamic driving style detected, pressure on
or multiple (roadworks, etc.),
- Adverse weather conditions.
the brake or accelerator pedal.
- Close proximity to the vehicle in front (lane
- Driving on racing circuits.
- Driving over lane markings.
markings may not be detected).
- Driving on a rolling road.
- Activation of the direction indicators.
– Roads that are narrow, winding.
Deactivation/Activation
- Crossing the inside line on a bend.
– Driving on a tight bend.
By default, the system is automatically activated
at every engine start.
141
Driving
It is configured in the ADAS touch screen
This system warns the driver of vehicles
The status of the system is memorised when the
application.
approaching rapidly from the rear in adjacent
ignition is switched off.
or
lanes (up to around 75 m) and of the presence of
The system is automatically deactivated
Direct access to the Shortcuts for driving aids.
a vehicle in the blind spots of their vehicle, using
when towing with a towing device
Deactivation is confirmed by the
corner radars located in the rear bumper.
approved by PEUGEOT.
illumination of this indicator lamp on the
This system takes into account vehicles
instrument panel.
such as cars, lorries and motorcycles by
Operating conditions
monitoring the blind spots or areas hidden
Malfunction
from the driver's field of vision.
- All vehicles are moving in the same direction
In the event of a malfunction,
and in adjacent lanes.
these warning lamps light up on
- When overtaking a vehicle, the speed
the instrument panel, accompanied by the
difference is less than 9 mph (15 km/h).
display of a message and an audible signal.
- Traffic is flowing normally.
Have it checked by a PEUGEOT dealer or a
- Overtaking a vehicle over a certain period of
qualified workshop.
time and the vehicle being overtaken remains in
the blind spot.
Long-distance blind spot
Operating limits
A warning lamp appears in the door mirror on the
monitoring
No alert is triggered in the following conditions:
side in question:
- presence of stationary objects (e.g. parked
- Fixed, immediately when another vehicle is in
For more information, refer to the
vehicles, safety rails, lampposts, signs).
the blind spot or is approaching in an adjacent
General recommendations on the use
- vehicles travelling in the opposite direction.
lane.
of driving and manoeuvring aids.
- if the rear bumper is damaged.
- Flashing, after about 1 second when the
direction indicator is used.
It is possible that warnings are not given,
are given too late or seem unjustified.
Activation/Deactivation
This system does not replace the need for
It is configured in the ADAS touch screen
vigilance on the part of the driver. Always
application.
check in the mirrors and look over your
When starting the vehicle, the warning lamp
shoulders before changing lanes to avoid an
comes on in each mirror to indicate that the
accident.
system is activated.
If the rear bumper is to be repainted, contact
a PEUGEOT dealer or a qualified workshop;
142
Driving
certain types of paint could interfere with the
and in the vehicle path defined by the direction of
Parking sensors
6
operation of the radars.
the steering wheel.
For more information, refer to the
General recommendations on the use
Malfunction
of driving and manoeuvring aids.
If the event of a malfunction, this warning
lamp lights up on the instrument panel,
accompanied by the display of a message.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Depending on version, in the example shown,
The system may be temporarily disturbed
only the obstacles present in the shaded area
by certain weather conditions (e.g. heavy
will be signalled by the audible assistance.
rain, hail or extreme temperature changes).
The proximity information is given by an
In particular, driving on a wet road or going
This system detects and signals the proximity of
intermittent audible signal, the frequency of
from a dry to a wet area can cause false
obstacles (e.g. pedestrian, vehicle, tree, barrier)
which increases as the vehicle approaches the
alerts (e.g. presence of a cloud of water
using sensors located in the bumper.
obstacle.
droplets in the blind spot interpreted as a
When the distance between the vehicle and
vehicle).
Rear parking sensors
the obstacle becomes less than about thirty
In bad or wintry weather, ensure that
► Engage reverse gear to start the system
centimetres, the audible signal becomes
the radars are not covered by mud, ice or
(confirmed by an audible signal).
continuous.
snow.
The system is switched off when reverse gear is
The sound emitted by the speaker (right or
Take care not to cover the warning zone in
disengaged.
left) indicates the side on which the obstacle is
the door mirrors, or the detection zones on
located.
the rear bumper, with adhesive labels or
Audible assistance
other objects; they may hamper the correct
Adjusting the audible signal
operation of the system.
Pressing this button opens the
window for adjusting the volume
of the audible signal.
The system signals the presence of obstacles
which are both within the sensors’ detection zone
143
Driving
Visual assistance
Deactivation/Activation
The rear parking sensors are deactivated
automatically if a trailer or bicycle carrier
(Depending on country of sale)
is connected to a towing device installed in
Depending on version, using the centre console
accordance with the Manufacturer's
button and/or in the ADAS application on the
recommendations.
touch screen.
In this case, the outline of a trailer is displayed
at the rear of the image of the vehicle.
When starting the vehicle, the graphic
This supplements the audible signal, without
and audible aids are only available after
taking account of the vehicle's trajectory, by
the touch screen has started up.
displaying bars on the screen whose location
represents the distance between the obstacle
and the vehicle (white: more distant, orange:
Operating limits
close, red: very close).
► Press this button to activate or deactivate the
If the boot is heavily loaded, the vehicle may tilt,
When the obstacle is very close, the "Danger"
function.
affecting distance measurements.
symbol is displayed on the screen.
The indicator lamp is lit when the function is
deactivated.
Malfunction
Front parking sensors
It is configured in the ADAS touch screen
In the event of a malfunction when
Supplementing the rear parking sensors, the
application.
changing into reverse gear, these
front parking sensors are triggered when an
If the function is deactivated, this indicator
warning lamps light up on the instrument panel,
obstacle is detected in front and the speed of the
lamp lights up on the instrument panel.
accompanied by the display of a message and
vehicle is below 6 mph (10 km/h).
The system status is saved when the ignition is
an audible signal (short beep).
Front parking sensor operation is suspended if
switched off.
In the event of a malfunction, this
the vehicle stops for more than three seconds in
indicator lamp flashes for approximately
forward gear, if an obstacle is no longer detected
10 seconds when reverse gear is engaged.
or the vehicle speed exceeds 6 mph (10 km/h).
Have it checked by a PEUGEOT dealer or a
qualified workshop.
The sound emitted by the speaker (front
or rear) locates the obstacle relative to
the vehicle, whether in front of or behind it on
its path.
144
Driving
Visiopark 1
The view type can be changed at any time
Settings
6
during the manoeuvre.
In the side menu, this menu allows you to
For more information, refer to the
The system status is not saved when the ignition
carry out the following operations:
General recommendations on the use
is switched off.
- adjust the volume of the audible signal.
of driving and manoeuvring aids.
- adjust the brightness.
Operating principle
- adjust the contrast.
When reverse gear is engaged, with the engine
running, this system displays views of the
Activation/Deactivation
vehicle's close surroundings on the touch screen
To activate the camera, engage reverse gear.
using a camera located at the rear of the vehicle.
The system is deactivated:
- when changing out of reverse gear.
- by pressing the cross in the top left-hand
corner of the touch screen.
Automatic zoom view
Using the camera, the vehicle's close
surroundings are recorded during low speed
manoeuvres.
An image from above the vehicle in its close
surroundings is created in real time (on the side
The screen is divided into 3 parts with a side
of the screen), as the vehicle progresses.
menu, a contextual view and a view from above
This view makes it easier to align the vehicle
the vehicle in its close surroundings.
when parking and to perceive nearby obstacles.
The rear camera records the vehicle's
The parking sensors supplement the information
It is automatically deleted if the vehicle remains
surroundings during the manoeuvre in order to
in the view from above the vehicle.
stationary for too long.
create a view from above the rear of the vehicle
Different contextual views are available:
An additional jet is fitted above the number plate
in its close surroundings, allowing the vehicle to
- Automatic zoom view.
to clean the reversing camera (depending on
be manoeuvred around nearby obstacles.
- Standard view.
version).
Using the sensors located on the rear bumper,
- Panoramic view.
► The washing of the reversing camera is
the automatic zoom view is displayed when
Depending on the context, the system chooses
triggered by operating the rear screenwash.
approaching an obstacle at the red line (less
the best view to display (standard or automatic
than 30 cm) during the manoeuvre.
zoom).
This view is only available automatically.
145
Driving
Obstacles may appear further away than
Panoramic view
they actually are.
It is important to monitor the sides of the
vehicle during the manoeuvre, using the
mirrors.
Parking sensors also provide additional
information about the area around the vehicle.
The panoramic view allows you to leave, in
Standard view
reverse, a parking space by anticipating the
arrival of vehicles, pedestrians or cyclists.
The screen is divided into 4 parts with two side
This view is not recommended for carrying out a
menus, a contextual view and a view from above
complete manoeuvre.
the vehicle in its close surroundings.
This view is only available by selection in the
The parking sensors supplement the information
side menu.
in the view from above the vehicle.
Depending on the view angle chosen in the
The area behind the vehicle is displayed on the
Visiopark 2
left-hand side menu, the system provides
screen.
specific visual assistance in particular driving
The blue lines 1 represent the width of your
For more information, refer to the
conditions, such as entering a blind intersection
vehicle, with the mirrors unfolded; their direction
General recommendations on the use
or manoeuvring in areas with reduced visibility.
changes according to the position of the steering
of driving and manoeuvring aids.
Different contextual views are available for the
wheel.
rear or for the front:
This system allows you to view your vehicle's
The red line 2 represents a distance of 30 cm
- Automatic zoom view.
close surroundings on the touch screen using
from the rear bumper; the two blue lines 3 and 4
- Standard view.
cameras, located at the front and rear of the
represent 1 m and 2 m, respectively.
- Panoramic view.
vehicle, as well as under the door mirrors.
This view is available automatically or by
Depending on the context, the system chooses
selection in the side menu.
the best view to display (standard or automatic
zoom).
The view type can be changed at any time
during the manoeuvre.
The system status is not saved when the ignition
is switched off.
146
Driving
Operating principle
Settings
Automatic zoom view
6
Reconstructed view
In the side menu, this menu allows you to
carry out the following operations:
The cameras are activated and a reconstruction
- adjust the volume of the audible signal.
of a view from above your vehicle in its close
- adjust the brightness.
surroundings is displayed on the touch screen.
- adjust the contrast.
Live view
Activation/Deactivation
The front or rear camera records the
Automatic
surroundings during the manoeuvre to create
With the rear camera, engine running and
a front or rear view from above the vehicle in
vehicle stationary, rear vision is displayed
its close surroundings, making it possible to
automatically if reverse gear is engaged.
manoeuvre the vehicle around the surrounding
With the front camera, engine running and speed
obstacles.
The front, rear and side views automatically
below 10 mph (16 km/h), front vision is displayed
Using the sensors located on the front or
appear in the view from above the vehicle.
automatically if a gear is engaged.
rear bumper, the automatic zoom view is
It is also possible to display any live view by
Manual
displayed when approaching an obstacle at the
selecting the corresponding zone.
red line (less than 30 cm) during the manoeuvre.
► In the ADAS touch screen application,
The front view can be selected in forward gear
This view is only available automatically.
select Functions>Panoramic camera
up to 10 mph (16 km/h).
Depending on version, it can be activated/
The system is deactivated:
deactivated in the ADAS application of the touch
Installing the very cold climate screen
- automatically for the rear, when changing out
screen.
can alter the image transmitted by the
of reverse gear.
front camera.
- automatically for the front, above
Obstacles may appear further away than
approximately 10 mph (16 km/h).
they actually are.
An additional jet is fitted above the number plate
- by pressing the cross in the top left-hand
It is important to monitor the sides of the
to clean the reversing camera (depending on
corner of the touch screen.
vehicle during the manoeuvre, using the
version).
mirrors.
► The washing of the reversing camera is
Parking sensors also provide additional
triggered by operating the rear screenwash.
information about the area around the vehicle.
147
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст