Citroen C-Crosser Dag (2008 year). Instruction — part 9
P R A C T I C A L I N F O R M A T I O N
IX
127
Parking the vehicle
Immobilise the vehicle where it does
not block traffi c: if possible, park the
vehicle on level, stable and non-
slippery ground.
Apply the handbrake, switch off the
ignition and engage fi rst gear to lock
the wheels.
If necessary, place a chock under
the wheel diagonally opposite the
wheel to be changed.
Never go underneath a vehicle
raised using a jack; use a stand.
Removing the wheel
List of operations
Fit the anti-theft socket 5 on the
wheelbrace 1 to unlock the anti-theft
bolt.
Unlock the other bolts using the
wheelbrace 1 only.
Place the jack 2 in contact with one
of the two front A or rear B locations
provided on the underframe, whi-
chever is closest to the wheel to be
changed.
Extend the jack 2 until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A
or B used.
Raise the vehicle until there is suffi -
cient space between the wheel and
the ground to admit the spare (not
punctured) wheel easily.
Remove the bolts and store them in
a clean place.
Remove the wheel.
P R A C T I C A L I N F O R M A T I O N
IX
128
After changing a wheel
When
using
the
“space-saving”
spare wheel, do not exceed a speed
of 50 mph (80 km/h).
Have the tightening of the bolts and
the pressure of the spare wheel
checked by a CITROËN dealer
without delay.
Have the punctured wheel repaired
and replace it on the vehicle as soon
as possible.
Fitting the wheel
List of operations
Lower the vehicle fully.
Fold the jack 2 and detach it.
Lock the anti-theft bolt using the
wheelbrace 1
fi tted with the anti-
theft socket 5 .
Lock the other bolts using the
wheelbrace 1 only.
Store the tools (refer to the
paragraph “Access to the tools”).
Fitting snow tyres
If you equip your vehicle with snow
tyres fi tted on steel wheel rims, it
is imperative that special bolts
available from your CITROËN dealer
are used.
Put the wheel in place on the hub.
Screw in the bolts by hand to the
stop.
Pre-tighten the anti-theft bolt using
the wheelbrace 1
fi tted with the anti-
theft socket 5.
Pre-tighten the other bolts using the
wheelbrace 1 only.
P R A C T I C A L I N F O R M A T I O N
IX
129
CHANGING A BULB
Handle the bulbs using a dry
cloth.
Do not clean the headlamps
using a dry or abrasive cloth, or us-
ing detergent or solvent products,
use a sponge and soapy water.
In
certain
climatic
conditions
(low temperature, humidity), t he
presence of condensation on the
inside of the headlamp glass is
normal ; it disappears a few minutes
after the lights are switched on.
Front lights
Blown bulb
Refer to the appropriate procedure to
change the corresponding bulb.
1. Direction indicators
(PY21W - 21 W).
2. Dipped headlamps (H11 - 55 W)
or xenon bulb (D2S - 35 W).
3. Side lights (W5W - 5 W).
4. Main beam headlamps
(H7 - 55 W).
5. Front fog lamps
(H11 - 55 W).
WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be replaced by a
CITROËN dealer.
Operating procedure for replacing a
faulty bulb with a new bulb.
P R A C T I C A L I N F O R M A T I O N
IX
130
Changing the direction
indicators (1)
Coloured bulbs must be replaced
with bulbs of identical specifi cation
and colour.
Turn the bulb holder A to the left
and remove it.
Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
Access to the bulbs
on the left-hand side
When you change a bulb on the left-
hand side, remove the relay box fi xing
nut B
and move the relay box towards
the rear.
Access to the bulbs
on the right-hand side
When you change a bulb on the right-
hand side:
Remove the screenwash reservoir
fi xing C and move the reservoir
towards the rear.
Remove the coolant reservoir fi xing
nut D .
Remove the clip E and raise the
reservoir moving it towards the
front.
P R A C T I C A L I N F O R M A T I O N
IX
131
Changing the side lights (3)
Unscrew the cover H .
Disconnect the connector.
Turn the bulb holder I a quarter of a
turn and remove it.
Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
Unscrew the cover F .
Disconnect the connector.
Turn the bulb G to the left and re-
move it.
To refi t, carry out these operations in
reverse order.
Changing the dipped headlamps (2)
Changing the main beam
headlamps (4)
Unscrew the cover J .
Disconnect the connector.
Move aside the spring K to release
the bulb and remove it.
To refi t, carry out these operations in
reverse order.
P R A C T I C A L I N F O R M A T I O N
IX
132
Changing the integrated direction
indicator side repeaters
Push the repeater A towards the
rear and detach it.
Unclip the repeater.
Disconnect the repeater connector
and change the repeater.
To refi t, carry out these operations in
reverse order.
To obtain repeaters, contact a CITROËN
dealer.
Changing the fog lamps (5)
Turn the wheel fully towards the out-
side for easy access to the fl ap A
located in the wheelarch.
Using a screwdriver, remove the four
clips B located in the wheelarch.
P R A C T I C A L I N F O R M A T I O N
IX
133
Using a screwdriver, remove the
three clips C located below the
bumper.
Lift the access fl ap D located in the
wheelarch and slide it downwards.
Disconnect the connector E .
Turn the bulb F to the left and
remove it.
To refi t, carry out these operations in
reverse order.
P R A C T I C A L I N F O R M A T I O N
IX
134
Rear lights
1. Third brake light (diodes).
2. Brake lights / Side lights
(21/5 - W21W - 5 W).
3. Direction indicators
(WY21W - 21 W).
4. Reversing lights (W21W - 21 W).
5. Number plate lights (W5W - 5W).
6. Fog lamps (W21W - 21 W).
Changing the brake lights / side
lights and direction indicators
These two bulbs are changed from
outside with the tailgate open:
Open the tailgate (refer to the
“Access” section),
Remove the two light fi xing bolts A ,
Extract the light from outside,
Turn the pin C to the left and remove it.
Pull the bulb D and change it.
To refi t, carry out these operations in
reverse order.
Turn the pin B to the left and remove it.
Pull the bulb and change it.
When refi tting the light, align the
two pins E with the openings on the
vehicle.
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifi cation
and colour.
Changing the third brake light
(diodes)
All work on the diode lights must be
carried out by a CITROËN dealer.
P R A C T I C A L I N F O R M A T I O N
IX
135
Changing the reversing lights
Open the tailgate (refer to the
“Access” section),
From the inside of the tailgate, in-
sert a screwdriver in the opening on
the cover A to use it as a lever to
open the cover.
Changing the number plate lights
Open the tailgate (refer to the
“Access” section) to gain access to
the number plate lights D ,
Remove the light unit D while
pressing it to the left.
Turn the pin B to the left and remove
it.
Pull the bulb C and change it.
To refi t, carry out these operations in
reverse order.
Insert a thin screwdriver in the ope-
ning on the lens to press the tab E .
Remove the lens.
Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
To refi t the light unit, insert the end
of the tab F
fi rst, then align the
tab G .
P R A C T I C A L I N F O R M A T I O N
136
Changing the fog lamps
Open the tailgate and the lower tail-
gate (refer to the “Access” section)
and fold down the cover A .
Remove the 4 clips B using a
screwdriver to detach the light
cover.
Remove the bolts C and remove the
light unit.
Turn the pin and bulb assembly D to
the left.
Remove the bulb.
To refi t, carry out these operations in
reverse order.
When refi tting the light unit, align
the clips E with the openings on the
bodywork.
P R A C T I C A L I N F O R M A T I O N
137
INTERIOR BULBS
Front and rear courtesy lights
Insert a screwdriver to remove the courtesy light cover.
Remove the bulb while pressing the tab A .
To refi t the cover, align the hooks on the holes located in the body of the vehicle.
Glove box light
Turn the pin B anticlockwise and re-
move it.
Remove the bulb.
Low level light
Insert a screwdriver to remove the
light cover.
Remove the bulb.
P R A C T I C A L I N F O R M A T I O N
IX
138
CHANGING A FUSE
Access to the tools
The extraction pliers are installed in the
engine compartment fuse box.
To gain access to them:
Open the bonnet (refer to the
“Access” section),
Press on the hook A and release the
catch,
Remove the cover completely,
Remove the pliers B .
CITROËN will not accept re-
sponsibility for the cost incurred
in repairing your vehicle or for
rectifying the malfunctions resulting
from the installation of accessories
not supplied and not recommended
by CITROËN and not installed in ac-
cordance with its instructions, in par-
ticular when the consumption of all of
the additional equipment connected
exceeds 10 milliamperes.
Your vehicle’s electrical system is
designed to operate with standard
or optional equipment.
Before installing other electrical
equipment or accessories in your
vehicle, contact a CITROËN dealer.
Changing a fuse
Before changing a fuse, the cause of the
failure must be identifi ed and rectifi ed.
Identify the faulty fuse by checking
the condition of its fi lament.
Use the special pliers to extract the
fuse from its location.
Always replace the faulty fuse with
a fuse of the same rating.
Check the correspondence between
the number etched on the box, the
rating etched on the top and the
tables below.
Correct
Incorrect
The spare fuses are located on the
engine compartment fuse box cover.
Operating procedure for replacing a
faulty fuse with a new fuse to rectify a
failure in the corresponding function.
P R A C T I C A L I N F O R M A T I O N
IX
139
Fascia fuses
The fuse boxes are placed in the lower
part of the fascia behind the enclosed
storage compartment (left-hand side).
Access to the fuses
Open the cover A ,
Pull it towards you to extract it,
Change the fuse (refer to the
corresponding paragraph).
Fuse N°
Rating
Functions
1
*
30 A
Heating.
2
15 A
Brake lights, third brake light, built-in systems
interface.
3
10 A
Rear fog lamps.
4
30 A
Windscreen wipers and wash-wipe.
5
10 A
Diagnostic socket.
6
20 A
Central locking, exterior mirrors.
7
15 A
Audio equipment, telematics, multifunction display,
hands-free kit, rear DVD player.
8
7.5 A
Remote control key, air conditioning control unit,
instrument panel, controls bar, steering wheel
controls.
9
15 A
Multifunction display, instrument panel.
10
15 A
Built-in systems interface.
11
15 A
Rear wiper.
12
7.5 A
Instrument panel, 4 wheel drive control unit,
air conditioning control panel, ABS control
unit, multifunction display, automatic headlamp
adjustment, heated seats, air bags control unit,
steering wheel angle sensor, sunroof, rear screen
demisting, remote control.
13
-
Not used.
14
10 A
Ignition switch.
15
20 A
Sunroof.
16
10 A
Exterior mirrors, audio equipment, telematics, rear
DVD player.
P R A C T I C A L I N F O R M A T I O N
IX
140
Access to the fuses
Open the cover A ,
Pull it towards you to extract it,
Change the fuse (refer to the
corresponding paragraph).
* The maxi-fuses provide additional protection for the electrical systems. All work on the maxi-fuses must be carried
out by a CITROËN dealer.
Fuse N°
Rating
Functions
17
10 A
4 wheel drive control unit.
18
7.5 A
Reversing lights, parking assistance control unit,
reversing camera, air bags control unit.
19
15 A
Accessories socket.
20*
30 A
Electric window controls.
21
*
30 A
Rear screen demisting.
22
7.5 A
Heated exterior mirrors.
23
-
Not used.
24
25 A
Driver’s electric seat, footwell lighting, releasing of
the rear bench seat.
25
30 A
Heated seats.
P R A C T I C A L I N F O R M A T I O N
IX
141
Engine compartment fuses
The fuse box is placed in the engine compartment near the
battery (left-hand side).
Access to the fuses
Open the bonnet (refer to the “Access” section),
Press on the hook A to release the catch,
Remove the cover completely,
Change the fuse (refer to the corresponding paragraph).
When you have fi nished, close the cover carefully to
guarantee the sealing of the fuse box.
Fuse N°
Rating
Functions
1
15 A
Front fog lamps.
2
7 A
Engine ECU 2.4 litre 16 V
3
20 A
CVT automatic gearbox ECU, relay
CVT automatic gearbox ECU
4
10 A
Horn.
5
7.5A
Alternator 2.4 litre 16V
6
20 A
Headlamp wash.
7
10 A
Air conditioning.
8
15 A
Engine ECU 2.4 litre 16 V
9
-
Not used.
10
15 A
Demisting, wipers.
11
-
Not used.
12
-
Not used.
13
-
Not used.
14
10 A
Left-hand main beam headlamp.
15
10 A
Right-hand main beam headlamp.
16
20 A
Left-hand dipped headlamp (xenon).
17
20 A
Right-hand dipped headlamp (xenon).
18
10 A
Left-hand dipped headlamp, manual
and automatic headlamp
adjustment.
19
10 A
Right-hand dipped headlamp.
20
-
Not used.
21
10 A
Ignition coils
P R A C T I C A L I N F O R M A T I O N
IX
142
Spare fuses
The spare fuses are located under the engine compartment
fuse box cover.
The cover does not contain spare fuses with an amper-
age of 7.5 A, 25 A or 30 A. If one of the fuses with these
amperages develops a fault, replace it with the following
fuse:
A 7.5 A fuse must be replaced with the 10 A spare fuse ,
a 25 A fuse with a 20 A spare fuse and a 30 A fuse with
the audio system fuse (N° 31) .
* The maxi-fuses provide additional protection for the electrical systems. All work on the maxi-fuses must be carried
out by a CITROËN dealer.
Fuse N°
Rating
Functions
22
20 A
Engine control unit, water in diesel detector, injection pump (Diesel), air fl ow sensor.
23
15 A
Petrol pump, fuel gauge.
24
*
30 A
Starter.
25
-
Not used.
26
*
40 A
ABS control unit, ASC control unit.
27*
30 A
ABS control unit, ASC control unit.
28
*
30 A
Condenser fan.
29
*
40 A
Radiator fan.
30
30 A
Passenger compartment fuse box.
31
30 A
Audio amplifi er.
32
30 A
Engine control unit
Fuse N°
Rating
33
10 A
34
15 A
35
20 A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст