Renault Kangoo (2022 year). Manual in english — page 12
ADVANCED SAFETY (5/17)
Active emergency braking
Special features of stationary
(continued)
vehicles
Stationary vehicles are detected when
Special features of oncoming
your vehicle is being driven at a speed
vehicles in the context of a
between approximately 5 mph (8 km/h)
manoeuvre to change direction
and 62 mph (100 km/h). The system is
When you wish to change direction
not active and does not emit a warn-
(e.g. A), oncoming vehicles travelling
ing for stationary vehicles when your
at approximately 18 mph (30 km/h) to
vehicle speed exceeds approximately
35 mph (55 km/h) are detected by the
62 mph (100 km/h).
system when:
A
- your vehicle is travelling at a speed
Special features of warnings
between approximately
5 mph
Depending on the speed, the warning
(8 km/h) to 12 mph (20 km/h);
and braking may be activated simulta-
- you have activated the direction indi-
neously.
cator light.
The system is otherwise inactive
and does not trigger an alert.
This function is an addi-
tional driving aid.
This function is not under
any circumstances in-
tended to replace the due care
and attention of the driver, who
should at all times be in control of
the vehicle.
2.77
ADVANCED SAFETY (6/17)
Active emergency braking
Note: if the driver uses the vehicle con-
(continued)
trols (steering wheel, pedals, etc.) the
system may delay certain operations or
Detection of pedestrians and
not activate.
cyclists
When driving at a speed between ap-
10
proximately 5 mph (8 km/h) and 53 mph
(86 km/h), if there is a risk of collision
with a cyclist or pedestrian, the system:
-
warns you of a collision risk:
the
red warning light, or, de-
pending on the vehicle, the dis-
play 10 and the message “Brake”
appear on the instrument panel, ac-
companied by a beep.
If active emergency braking has caused
If the driver presses the brake pedal
the vehicle to stop, the vehicle is kept
and the system still detects a risk of
stationary for a short time. Beyond this
collision, the braking force may be
time limit, the vehicle must be held sta-
increased if it is not sufficient to pre-
tionary by the driver keeping their foot
vent the collision.
on the brake pedal.
-
may trigger braking:
if the driver fails to react following
the alert and collision becomes im-
minent.
In the event of emergency manoeu-
vre, you can stop braking at any
moment by:
- tapping the accelerator pedal;
or
- turning the steering wheel as a
collision avoidance manoeuvre.
2.78
ADVANCED SAFETY (7/17)
Active emergency braking
4
(continued)
Settings for vehicles equipped with
a multimedia screen
To access the multimedia screen func-
tion settings 4, refer to the multimedia
instructions:
- “Alert”: adjust the alert sensitivity
level. To do this select:
6
- “At the latest”;
7
- “Standard”;
- “At the sooner”.
8
9
Please refer to the multimedia instruc-
Settings for vehicles not equipped
-
press control 7 or 8 repeatedly to
tions for further information.
with a multimedia screen
reach the DRIVING ASSIST menu.
Press the switch 8 OK;
- With the vehicle stopped, press the
switch 6 as many times as required
-
scroll repeatedly by pressing con-
to reach the “Vehicle” tab;
trol 7 or 8 to reach the “Active brak-
ing sensitivity” menu. Press the
- press the 7 or 8 control repeatedly to
switch 9 OK;
reach the “Settings” menu. Press the
switch 9 OK;
-
press the 7 or 8 control repeatedly
to adjust the setting. Press the 9 OK
button.
2.79
ADVANCED SAFETY (8/17)
Active emergency braking
The possible causes are:
Operating faults
(continued)
-
the system is temporarily blinded
When the function detects an operat-
(glare from the sun, dipped beam
Temporarily not available
headlights, bad weather conditions
etc.). The system will be operational
or, depending on the vehicle,
If the system detects a temporary fault
again when visibility conditions are
the
warning light illuminates, or
better;
and
, appear in yellow
-
the system is temporarily interrupted
on the instrument panel accompanied
depending on the vehicle, the
(e.g. the windscreen or the front or
by the message “Check Front camera”
warning light illuminates in yellow on
rear bumper is obscured by dirt,
or “Front radar to check” or “Check
the instrument panel.
mud, snow, condensation, etc.). In
Camera/Radar”.
this case, park the vehicle and switch
Consult an approved dealer.
off the engine. Clean the windscreen
and front bumper. The next time the
engine is started, after five or ten
minutes of driving, the warning light
and the message disappear.
If this is not the case, this may arise from
another cause; contact an Approved
Dealer.
2.80
ADVANCED SAFETY (9/17)
Active emergency braking
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle. The triggering of this function may be
delayed or prevented when the system detects clear signs of control of the vehicle by the driver (action on the steer-
ing wheel, pedals etc.).
The system cannot be activated:
- when the gearbox lever is in neutral or the clutch pedal has been depressed for approximately two seconds;
- when the parking brake has been activated for approximately ten seconds.
System servicing/repairs
- In the event of an impact, the radar and/or camera alignment may be changed and its operation may consequently be af-
fected. Deactivate the function and consult an authorised dealer.
- Any work in the area where the radar and/or camera is located (repairs, replacements, windscreen modifications, etc.) must
be carried out by a qualified professional.
Only an authorised dealer is qualified to service the system.
2.81
ADVANCED SAFETY (10/17)
System disturbance
Some conditions can disturb or damage the operation of the system, such as:
- a complex environment (metal bridge, tunnel etc.);
- poor weather conditions (snow, hail, black ice etc.);
- poor visibility (night, fog etc.);
- poor contrast between the object (vehicle, pedestrian etc.) and the surrounding area (e.g. pedestrian dressed in white lo-
cated in a snowy area etc.) ;
- being dazzled (glaring sun, lights of vehicles travelling in the opposite direction etc.);
- windscreen obscured (by dirt, ice, snow, condensation etc.);
- ...
In these conditions, the system may not react, may warn the driver or may brake inadvertently.
Limitation of the system operation
- Each time the vehicle is started, the system carries out a calibration according to the vehicle surroundings and may be in-
active for a length of time between approximately two to five minutes of driving;
- An oncoming vehicle will not trigger any warning or system action if the conditions in the paragraph “Special features of on-
coming vehicles in the context of a manoeuvre to change direction” are not met (see previous pages);
- The radar and camera zones must be kept clean and free of any tampering in order to ensure the proper operation of the
system;
- the system may not respond to small vehicles such as motorbikes as effectively as to other vehicles;
- the system may not operate properly when the road surface is slippery (rain, snow, black ice, etc.);
- to ensure correct operation, the system needs to distinguish the complete outline of the pedestrian. So the system cannot
detect:
- pedestrians in the darkness or in poor lighting conditions;
- partially visible pedestrians:
- pedestrians less than approximately 80 cm tall;
- pedestrians carrying large objects;
- ...
In these conditions, the system may not react or may brake inadvertently.
2.82
ADVANCED SAFETY (11/17)
Deactivating the function
You must disable the function if:
- the brake lights are not functioning;
- the area of the camera has been damaged (e.g. on the inside or outside of the windscreen);
- the front of the vehicle was damaged (impact, distortion, scratch on the radar etc.);
- the vehicle is being towed (breakdowns);
- the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an approved
dealer);
- you are not driving on a paved road.
In the event of the system behaving abnormally, deactivate it and consult an authorised dealer.
Halting the function
You can halt the active braking function at any time by tapping the accelerator pedal or by turning the steering wheel in a col-
lision avoidance manoeuvre.
2.83
ADVANCED SAFETY (12/17)
Depending on the vehicle, using in-
1
formation from the radars 3 and the
camera 1, the function triggers cor-
3
rective action on the vehicle steering
system in the event of a risk of colli-
sion with a vehicle moving at the same
speed or at a higher speed, if within the
detection area of the rear radars.
2
You can retake control of the ve-
Emergency Lane Keep Assist
Using information from the radar 2 and
hicle at any time by operating the
the camera 1, the function triggers cor-
Using information from the camera 1,
steering wheel.
rective action on the vehicle steering
the function triggers corrective action
system in the event of a risk of collision
on the vehicle steering system when
with a vehicle coming from the opposite
approaching the roadside (divider, bar-
direction in the adjacent lane, without
rier, pavement, embankment etc.) with-
the direction indicator having been ac-
This system provides an
out the direction indicator light having
tivated.
additional driving aid.
been activated.
This system is not, under
any circumstances, in-
tended to replace the due care and
attention of the driver, who should at
all times be in control of the vehicle.
2.84
ADVANCED SAFETY (13/17)
Emergency Lane Keep Assist
(continued)
Roadside detection
When driving at a speed between ap-
proximately
43 mph (70 km/h) and
110 mph (180 km/h), when approach-
ing the roadside (on the ground, barrier,
pavement, embankment etc.), without
11
the direction indicator having been acti-
vated, the system:
- warns you of a collision risk:
the
warning light appears in
red or, depending on the vehicle,
the 11 display appears on the instru-
Special feature
ment panel accompanied by a beep;
and
In the event the function operates re-
peatedly when approaching the road-
- triggers corrective action on the
side, if the system does not detect any
steering system.
hands on the steering wheel, the
warning lights appear in yellow on the
This function is an
addi-
instrument panel.
tional driving aid.
This function is not under
any circumstances in-
tended to replace the due care and
attention of the driver, who should at
all times be in control of the vehicle.
2.85
ADVANCED SAFETY (14/17)
Emergency Lane Keep Assist
(continued)
Detection of an oncoming vehicle
When driving at a speed between ap-
proximately
43 mph (70 km/h) and
68 mph (110 km/h), if there is a risk of
collision with a vehicle coming from the
opposite direction in an adjacent lane
11
B
and within the detection zone B, with-
out the direction indicator having been
activated, the system:
- warns you of a collision risk:
the
warning light appears in
red or, depending on the vehicle,
the 11 display appears on the instru-
ment panel accompanied by a beep;
You can interrupt the trajectory cor-
and
rection at any time by moving the
steering wheel.
- triggers corrective action on the
steering system.
This function is an addi-
tional driving aid.
This function is not under
B
any circumstances in-
tended to replace the due care
and attention of the driver, who
should at all times be in control of
the vehicle.
2.86
ADVANCED SAFETY (15/17)
Emergency Lane Keep Assist
(continued)
Detection of a vehicle approaching
from the rear
(depending on the vehicle)
While driving at a speed below 43 mph
(70 km/h) and 110 mph (180 km/h), if a
line (continuous or broken) is crossed
while there is a risk of collision with a
C
vehicle located in the blind spot C and it
12
is moving in the same direction as your
vehicle or with a vehicle that is rapidly
approaching from behind or in an adja-
cent lane that is in the detection area D,
the system:
- warns you of the risk of collision:
the warning light 12 flashes and the
warning light appears in red,
or, depending on the vehicle, the 13
display lights up on the instrument
panel accompanied by a beep;
and
- triggers corrective action on the
steering system.
13
D
2.87
ADVANCED SAFETY (16/17)
Emergency Lane Keep Assist
Conditions for non-activation of the
If the vehicle is towing a trailer or car-
(continued)
system
avan, unexpected or unnecessary cor-
rections may occur. In this case you
The system cannot be activated when:
Temporarily not available:
can deactivate the “Advanced Security”
- reverse gear is engaged;
function to avoid unexpected or unnec-
- very fast lane departure;
- the field of vision of the camera is ob-
essary corrections.
- driving continuously on a line;
structed;
- approximately four seconds after
- the front radar is obscured;
Operating faults
changing lanes;
- the rear radars are obscured;
- tight bends;
When the function detects an operat-
- the û
warning light is displayed.
- impaired visibility;
ing fault, the
and
or, de-
- activating the direction indicator
If one of the side radars is obscured,
light;
- strong acceleration;
the
warning light, or, depend-
warning lights appear in yellow
- emergency braking;
ing on the vehicle, the
warning
on the instrument panel accompanied
- changing the lane width;
light appears in yellow accompanied by
by the message “Check Front camera”
- operation of the active emergency
the message “Side radars no visibility”.
or “Front radar to check” or “Check
braking system.
Clean the area where the sensors are
Camera/Radar” or “Check Side radars”.
- ...
located.
Consult an approved dealer.
Depending on the vehicle, if one of the
If the vehicle is equipped with a towbar
side radars is obscured the message
that is recognised by the system, the
“Check Side radars” will appear on the
instrument panel.
warning light, or, depending on
the vehicle, the
warning light
appears in yellow accompanied by the
message “Trailer: side radars OFF” to
inform you that the Emergency Lane
Keep Assist is not operational.
2.88
ADVANCED SAFETY (17/17)
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle.
System servicing/repairs
- In the event of an impact, the alignment of the camera or radar(s) may be altered and its operation may consequently be
affected. Deactivate the function and consult an authorised dealer.
- Any work in the area where the camera or radars are located (replacements, repairs, windscreen modifications etc.) must
be carried out by a qualified professional.
Only an authorised dealer is qualified to service the system.
In the event of system disturbance
Some conditions can disturb or damage the operation of the system, such as:
- windscreen obscured (by dirt, ice, snow, condensation etc.);
- a complex environment (tunnel etc.);
- poor weather conditions (snow, rain, hail, black ice etc.) ;
- poor visibility (night, fog etc.);
- the road markings are irregular or difficult to distinguish (e.g. partially erased, excessive spacing, distorted road surface) ;
- being dazzled (glaring sun, lights of vehicles travelling in the opposite direction etc.);
- the road is narrow, winding or undulating (tight bends etc.);
- closely following a vehicle travelling in the same lane.
In this case, the “Advanced Safety” function may react incorrectly or not at all.
Risk of unwanted, incorrect correction or no correction of trajectory.
Deactivating the function
You must disable the function if:
- the camera area (on the windscreen side or the interior rear-view mirror side) or radar area(s) have been damaged;
- the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an Authorised
Dealer);
- the vehicle is being towed (breakdowns);
- you are not driving on a paved road.
2.89
FATIGUE DETECTION WARNING (1/2)
The fatigue detection warning is a func-
1
tion which is useful on monotonous
roads (motorways, high-speed roads
etc.).
It analyses driver behaviour and takes
account of events to inform you of any
risk of fatigue such as:
- steering wheel movement;
- driver actions on other devices (indi-
cators, windscreen washer etc.);
- time spent driving without stopping;
- ...
Activation/deactivation
Vehicles fitted with a multimedia
screen 1
To activate or deactivate the function,
refer to the multimedia instructions.
This function is an addi-
Select ON or OFF.
tional driving aid in case of
risk of fatigue. This function
does not take the place of
the driver.
Under no circumstances should this
function replace the driver’s care or
responsibility whilst driving.
The function is activated by default
every time the vehicle is started.
2.90
FATIGUE DETECTION WARNING (2/2)
- repeatedly press the control 3 up or
When a risk of fatigue is detected,
down until you reach the Fatigue de-
the message “Fatigue warning have a
tection warning menu, then press the
break” is displayed on the instrument
switch 2 OK .
panel accompanied by a beep.
- press the 2 OK switch again to acti-
Press switch 2 OK to delete the warn-
vate or deactivate the function.
ing.
It is advisable to stop as soon as pos-
2
Operation
sible for a break.
The function is set to notify the
Note:
driver if:
- if the warning is not deleted by press-
- the vehicle is driven for at least five
ing switch 2 OK, the beep repeats;
3
minutes after each time the vehicle is
- the function may interpret certain
stopped
driving styles as a sign of tiredness
- the vehicle speed is greater than ap-
(sporty driving, incorrect driving etc.)
proximately 40 mph (65 km/h);
Vehicles not fitted with a multimedia
or driving along a road which is in
and
screen
poor condition.
- approximately
10 minutes have
- With the vehicle at a standstill, press
passed since the deletion of the pre-
and hold the switch 2 OK to access
vious warning.
Operating faults
the settings menu;
The function triggers an alert if the
If the system detects a fault, the mes-
– repeatedly press the control 3 up or
system detects repeated signs of fa-
sage “Check fatigue warning” is dis-
down until you reach the “Driving as-
tigue in the driver at the steering wheel.
played on the instrument panel. Call an
sistance” menu. Press the switch 2
approved Dealer.
OK;
2.91
DETECTION OF ROAD SIGNS (1/4)
Note: make sure the windscreen is not
For vehicles equipped with a navigation
1
obscured (dirt, mud, snow, condensa-
system and if the vehicle is travelling in
tion etc.).
a country where the speed units differ
from those of the vehicle, the system
For vehicles which are equipped with it,
displays the speed limit sign in the unit
the system also uses information from
of the country, alongside the speed limit
the navigation system.
converted to the unit used by the vehi-
Once the speed limiter is activated, you
cle’s instrument panel.
can adjust the speed limiter indication
For countries where the speed limit is
displayed by the system.
reduced during rainy weather on some
If the limit speed is exceeded, the dis-
types of roads, on vehicles equipped
play panel is modified to warn the driver.
with a navigation system, the system
can modify the limited speed after a few
seconds of wiping the windscreen.
Special situations
The system detects speed limit signs
The system does not take into account
on the side of the road and displays the
exceptional speed limit measures, such
speed limit on the instrument panel.
as peak pollution days.
It mainly uses information taken from
the camera 1, attached to the wind-
screen behind the rear view mirror.
2.92
DETECTION OF ROAD SIGNS (2/4)
Vehicles not fitted with a multimedia
2
screen
- With the vehicle stopped, press the
switch 3 as many times as required
to reach the “Vehicle” tab;
- press the 4 or 5 control repeatedly to
reach the “Settings” menu. Press the
switch 6 OK;
- press the 4 or 5 control repeatedly to
reach the “DRIVING ASSIST” menu.
3
4
Press the switch 6 OK;
- press the 4 or 5 control repeatedly
to reach the “Speed alert” menu and
press the 6 OK switch;
6
5
– press the 6 OK switch to activate or
deactivate the function:
Activating/deactivating the
With the function activated, depending
on local regulations, you can activate
system
=
function activated
the “Display risk areas” option. The
Vehicles fitted with a multimedia
system will notify you of the distance
<
function deactivated
screen 2
separating you from this zone, and
while you are travelling in the zone.
To activate or deactivate the function,
refer to the multimedia instructions.
Select “ON” or “OFF”.
2.93
DETECTION OF ROAD SIGNS (3/4)
If the speed limit is exceeded, the circle
7
8
around the panel flashes (7 warning
light) along with a sound signal to warn
the driver.
9
10
Operation
Variation of the limit speed or
cruising speed
Warning lights
If the speed limiter, cruise control or
The function displays the following
adaptive cruise control notification
warning lights:
speed differs from the detected speed
7 Speed limit road signs
value, press and hold the following
switches:
8 Additional road signs (start or end
of “No overtaking” zone, slip road
- 9 (RES/+) to increase the notification
speed limit, speed in case of a cara-
speed to the detected speed;
van, speed limit with length of appli-
- 10 (SET/-) to reduce the notification
cation, etc.)
speed to the detected speed.
2.94
DETECTION OF ROAD SIGNS (4/4)
Operating faults
The system cannot detect the speed
limit if:
- the windscreen is not clean;
- the camera is blinded by the sun;
- there is insufficient visibility (night,
fog etc.) ;
- the signs are not legible (snow, etc.)
or are hidden (by another vehicle or
by trees);
- the information taken from the navi-
This function is an additional driving aid. This function is not under any
gation system is not up to date.
circumstances intended to replace the due care and attention of the
driver, who should at all times be in control of the vehicle.
The driver should always adapt their speed to the traffic conditions, re-
gardless of the system indications.
The system detects speed limit signs and does not detect other signs (e.g. entry/
exit to/from urban areas, etc.).
The system may not detect all speed limit signs or may interpret them incorrectly.
The driver should not ignore signs that are not detected by the system and should,
as a priority, comply with the traffic signage and the highway code.
In the event of poor visibility (fog, snow, frost, etc.), it is possible that the system
may not indicate the correct speed to the driver.
The driver should always adapt their speed to the traffic conditions, regardless of
the system indications.
2.95
SPEED LIMITER (1/4)
The speed limiter function controls the
engine and braking system to help
you not to exceed a driving speed that
you have chosen, known as the limit
speed.
5
4
1
3
2
Controls
1 Speed limiter On/Off switch.
2 Cruise control On/Off switch.
3 Switch to activate and decrease the
limit speed (SET/-).
4 Switch to activate and increase the
limit speed or to set the stored limit
speed (RES/+).
5 Speed limiter function standby (with
limited speed memory) (0).
You can link the speed limiter to
the “Road sign detection” function.
➥ 2.92.
2.96
SPEED LIMITER (2/4)
6
6
4
1
3
Driving
Switching on
To store the current speed, press
the 4 switch (RES/+) or the 3 switch
When a limit speed has been set but
Press the switch 1. The 6 warning light
(SET/-): the limit speed replaces the
not yet reached, driving is similar to
appears in grey. The “Speed limiter ON”
dashes and, depending on the vehicle,
driving a vehicle without the speed lim-
message appears on the instrument
the 6 warning light appears in white.
iter function.
panel accompanied by dashes to indi-
The minimum stored speed is 19 mph
cate that the speed limiter function is in
Once you have reached the stored
(30 km/h).
operation, waiting to store a limit speed.
speed, no effort on the accelera-
tor pedal will allow you to exceed
the programmed speed except in an
emergency (refer to information on
“Exceeding the limit speed”).
Please note that you must
keep your feet close to the
pedals in order to react in
an emergency.
2.97
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст