Renault Kangoo (2022 year). Manual in english — page 11
LANE KEEPING ASSIST (4/6)
Temporarily not available
Conditions for non-activation
4
– very fast lane departure;
of the system
- driving continuously on a line;
The system cannot be activated when:
– four seconds approximately after
- reverse gear is engaged;
changing lanes;
- the field of vision of the camera is ob-
– tight bends;
structed;
– impaired visibility;
- activating the direction indicator
- the û
warning light is displayed.
light;
The
warning light and the left/
- strong acceleration;
right line warning lights are displayed in
- emergency braking;
grey on the instrument panel.
- changing the lane width;
If the vehicle is equipped with a towbar
- operation of the active emergency
that is recognised by the system, the
braking system;
message “Trailer: side radars OFF” is
- ...
displayed to inform you that the Lane
Keep Assist system is not operational.
–
“Alert”: adjust the line detection sen-
If the function is unavailable, the
sitivity level. To do this select:
warning light and the left/right correc-
- “At the latest”: line detected when
tion warning lights 3 appear in grey on
Adjustment
crossing;
the instrument panel.
Vehicles fitted with a multimedia
- “Standard”: line detected on ap-
screen.
proach;
To access the multimedia screen func-
- “At the sooner”: line detected
tion settings 4, refer to the multimedia
nearby.
instructions:
- “VIBRATION”: adjust steering wheel
Please refer to the multimedia instruc-
vibration for the
“Lane Departure
tions for further information.
Warning” function;
2.56
LANE KEEPING ASSIST (5/6)
- press the 6 or 7 control repeatedly to
Operating faults
reach the “DRIVING ASSIST” menu.
When the system detects an operating
Press the switch 8 OK;
fault, the
warning light lights up
– scroll repeatedly by pressing 6 or 7
on the instrument panel, with the mes-
to reach the “Lane Keeping Assist
sage “Check Front camera”.
sensitivity” menu. Press the switch 8
Consult an approved dealer.
OK ;
- scroll repeatedly pressing control 6
or 7 to adjust the setting. Press the 8
OK button.
5
6
8
7
Adjustments (continued)
Vehicles not fitted with a multimedia
screen
- With the vehicle stopped, press the
switch 5 as many times as required
to reach the “Vehicle” tab;
- press the 6 or 7 control repeatedly to
reach the “Settings” menu. Press the
switch 8 OK;
2.57
LANE KEEPING ASSIST (6/6)
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle.
System servicing/repairs
- In the event of an impact, the camera alignment may be changed, and its operation may consequently be affected. Deactivate
the function and consult an authorised dealer.
- Any work in the area where the camera is located (repairs, replacements, windscreen modifications etc.) must be carried
out by a qualified professional.
Only an authorised dealer is qualified to service the system.
In the event of system disturbance
Some conditions can disturb or damage the operation of the system, such as:
- windscreen obscured (by dirt, ice, snow, condensation etc.);
- a complex environment (tunnel etc.);
- poor weather conditions (snow, rain, hail, black ice etc.) ;
- poor visibility (night, fog etc.);
- the road markings are irregular or difficult to distinguish (e.g. partially erased, excessive spacing, distorted road surface) ;
- being dazzled (glaring sun, lights of vehicles travelling in the opposite direction etc.);
- the road is narrow, winding or undulating (tight bends etc.);
- closely following a vehicle travelling in the same lane.
In this case, the “Lane Keeping Assist” may react incorrectly or not at all.
Risk of unwanted, incorrect correction or no correction of trajectory.
Deactivating the function
You must disable the function if:
- the area of the camera has been damaged (on the windscreen side or the interior rear-view mirror side);
- the road is slippery (snow, black ice, aquaplaning, gravel etc.) ;
- the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an Authorised
Dealer);
- the vehicle is connected to a towbar that is not recognised by the system;
- the vehicle is entering an area with several surface markings (an area with road works etc.).
2.58
BLIND SPOT WARNING (1/10)
2
C
1
C
Depending on the vehicle, there are
A system
two types of blind spot warning system:
Using information from the ultrasonic
- System A: uses information from
sensors indicated by the arrows 2,
ultrasonic sensors fitted in the vehi-
that are fitted in the vehicle bumpers,
cle bumpers. When activated, the
the system notifies the driver when an-
system A can be identified by indi-
other vehicle appears in the detection
cator light 1 flashing each time the
zone C.
engine starts;
The system is activated when the
- System B: uses information from
vehicle speed is between approxi-
This function is an addi-
the radars fitted on each side of the
mately 18 mph (30 km/h) and 80 mph
tional driving aid. This func-
rear bumper. When activated, the
(130 km/h).
tion is not under any cir-
system B can be identified by indi-
cumstances intended to
cator light 1 not flashing each time
replace the due care and attention
the engine starts.
of the driver, who should at all times
be in control of the vehicle.
2.59
BLIND SPOT WARNING (2/10)
1
C
3
C
A system
Indicator 1
Operation
(continued)
An indicator light 1 is located on each
The function alerts you if your ve-
rear view mirror 3.
hicle speed is between approxi-
Special feature
mately 18 mph (30 km/h) and 80 mph
Note: clean the rear view mirrors 3 reg-
Ensure that the ultrasonic sensors in-
(130 km/h) while another vehicle is
ularly so that the indicators 1 can be
stalled in the vehicle bumpers are not
in the blind spot C and moving in the
seen.
obscured (by dirt, mud, snow etc.).
same direction as your vehicle.
If one of the sensors is obscured, the
If you overtake another vehicle, the in-
message “Side radars no visibility” will
dicator 1 will only come on if that vehi-
appear on the instrument panel. Clean
cle remains for a long enough period in
the ultrasonic sensor zones.
your vehicle’s blind spot C.
2.60
BLIND SPOT WARNING (3/10)
Display E
Conditions for non-function
1
Direction indicator activated, the 1
- When driving on a road with tight
warning light flashes when the func-
bends;
tion detects a vehicle in the blind spot
D
- in reverse;
warning area and/or a vehicle is rapidly
approaching from the rear on the side
- speed below 18 mph (30 km/h);
towards which you will turn the wheel.
- speed above 80 mph (130 km/h).
If you cancel the direction indicator, the
If the vehicle is equipped with a towbar
function will return to the initial warning
E
recognised by the system, the “Trailer:
(display D).
side radars OFF” message displayed
on the instrument panel informs you
that the function is not operational. For
information on the range of equipment
adapted to your vehicle, we advise you
to consult an approved Dealer.
A system
(continued)
Display D
First warning: when the direction in-
dicator is not activated, the 3 warning
light signals that a vehicle is detected in
the blind spot.
2.61
BLIND SPOT WARNING (4/10)
G
C
F
C
F
B system
Special feature
Using information from the sensors in-
Ensure that the G area around the
stalled on each side of the rear bumper
radars on each side of the rear bumper
(area G), the function warns the driver:
are not obstructed (by dirt, mud, snow
etc.)
- when another vehicle appears in the
detection area C;
If a radar is obscured, the message
“Side radars no visibility” will appear on
and/or
This function is an addi-
the instrument panel. Clean the radar
– when there is a risk of collision with a
tional driving aid. This func-
area.
vehicle that is in area F, driving faster
tion is not under any cir-
than you.
cumstances intended to
replace the due care and attention
The function warns you when the ve-
of the driver, who should at all times
hicle is travelling at a speed above ap-
be in control of the vehicle.
proximately 9 mph (15 km/h).
2.62
BLIND SPOT WARNING (5/10)
1
C
F
3
C
F
B system
Operation
If you overtake another vehicle, the in-
(continued)
dicator 1 will only come on if that vehi-
The function warns you when the speed
cle remains for a long enough period in
of your vehicle is over 9 mph (15 km/h):
Indicator 1
your vehicle’s blind spot C.
- when another vehicle is in the blind
An indicator light 1 is located on each
spot area C and travelling in the
rear view mirror 3.
same direction as your vehicle;
- when a vehicle approaches quickly
Note: clean the rear view mirrors 3 reg-
from the rear in an adjacent lane
ularly so that the indicators 1 can be
within the range of detection area F.
seen.
The function does not notify the
driver if the other vehicles are not
moving.
2.63
BLIND SPOT WARNING (6/10)
Display E
Conditions for non-function
1
Direction indicator activated, the 1
- When driving on a road with tight
warning light flashes when the func-
bends;
tion detects a vehicle in the blind spot
D
- in reverse.
warning area and/or a vehicle is rapidly
approaching from the rear on the side
If the vehicle is equipped with a towbar
towards which you will turn the wheel.
recognised by the system, the “Trailer:
If you cancel the direction indicator, the
side radars OFF” message displayed
function will return to the initial warning
on the instrument panel informs you
E
(display D).
that the function is not operational. For
information on the range of equipment
adapted to your vehicle, we advise you
to consult an approved Dealer.
B system
(continued)
Display D
First warning: direction indicator not
activated, the 1 warning light indicates
that a vehicle is detected in the blind
spot area and/or that a vehicle is rap-
idly approaching from the rear in an ad-
jacent lane.
2.64
BLIND SPOT WARNING (7/10)
- press the 6 or 7 control repeatedly to
4
reach the “DRIVING ASSIST” menu.
Press the switch 8 OK;
- press the 6 or 7 control repeatedly to
reach the “Blind spot alert” menu and
press the 8 OK switch;
- press the switch 8 OK again to acti-
vate or deactivate the function:
5
=
function activated
6
<
function deactivated
8
7
Systems A and B
Vehicles not fitted with a multimedia
screen
- With the vehicle stopped, press the
Activation/deactivation
switch 5 as many times as required
When the engine is started, the
Vehicles fitted with a multimedia
to reach the “Vehicle” tab;
system recalls the last position
screen 4
- press the 6 or 7 control repeatedly to
stored before the ignition was
To activate or deactivate the function,
reach the “Settings” menu. Press the
switched off.
refer to the multimedia instructions.
switch 8 OK;
Select “ON” or “OFF”.
The system’s detection range oper-
ates according to a standard lane
width. When driving in a narrow
lane, the function can warn you
when a vehicle is detected beyond
the adjacent lane.
2.65
BLIND SPOT WARNING (8/10)
Systems A and B
(continued)
Operating faults
If the system detects a fault, the mes-
sage “Check Side radars” is displayed
on the instrument panel. Consult an ap-
proved dealer.
-The system’s detection
range operates according
to a standard lane width. If
you are driving in wide traf-
fic lanes, the system might not
be able to detect a vehicle in the
blind spot.
- The system might be disrupted
momentarily if it is exposed to
strong electromagnetic waves
(as beneath high-tension power
Due to the presence of radars or ul-
lines) or to very poor weather
trasonic sensors (depending on the
conditions
(heavy rain, snow
vehicle) behind the bumper, it is ad-
etc.). Remain aware of driving
visable to entrust any operation on
conditions.
the bumper (repair, replacement,
There is a risk of accidents.
paintwork etc.) to a qualified profes-
sional.
2.66
BLIND SPOT WARNING (9/10)
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle.
The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
The system should under no circumstances be taken to be an obstacle detector or an anti-collision system.
System servicing/repairs
- In the event of an impact, the alignment of the radars or ultrasonic sensors (depending on the vehicle) may be altered and
their operation may consequently be affected. Deactivate the function and consult an authorised dealer.
- Any work (repairs, replacements etc.) in the area where the radars or ultrasonic sensors (depending on the vehicle) are lo-
cated must be carried out by a qualified professional.
Only an authorised dealer is qualified to service the system.
System disturbance
Some conditions can disturb or damage the operation of the system, such as:
- complex surroundings (metal bridges, tunnels, roads with barriers at the edge, etc.);
- poor weather conditions (snow, hail, black ice, etc.).
Risk of false alarms or absence of warnings
In the event of the system behaving abnormally, deactivate it and consult an authorised dealer.
2.67
BLIND SPOT WARNING (10/10)
Limitation of the system operation
- The radars or ultrasonic sensors area (depending on the vehicle) should be kept clean and free of any modifications
in order to ensure the proper operation of the system.
- Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the system.
- When turning into a bend, the radars or ultrasonic sensors (depending on the vehicle) may temporarily cease to detect ve-
hicles in adjacent lanes.
- The function may warn you late if two other vehicles are approaching from the rear, driving side by side in the adjacent lanes
(i.e. driving on a 3-lane road) at a much higher speed than your vehicle.
- The system may not provide a warning when the other vehicles are travelling at a significantly different speed.
- If the vehicle is being overtaken by a long vehicle (e.g. heavy goods vehicle overtaking at a similar speed to the vehicle) the
system may interrupt the warning before the end of the manoeuvre.
- The vehicle is travelling on a winding road.
Deactivating the function
You must disable the function if:
- There has been damage in the area where the radars or ultrasonic sensors (depending on the vehicle) are located;
- the vehicle is fitted with a towbar that is not recognised by the system.
2.68
SAFE DISTANCE ALERT (1/4)
The function is activated when the vehi-
1
cle speed is between about 19 and
124 mph (30 and 200 km/h).
Location of the camera 1
Make sure the windscreen is not ob-
scured (by dirt, mud, snow, condensa-
tion etc.).
Location of the front radar 2
Ensure that the radar area is not ob-
structed (by dirt, mud, snow, a badly
fitted front number plate), impacted,
modified (including painting) or hidden
by any accessory fitted on the front of
2
the vehicle (on the grille or logo etc.).
Using the information from the radar 2
and camera 1, this function informs the
driver of the time interval between their
vehicle and the vehicle in front so that a
safe stopping distance between the two
vehicles can be maintained.
This function is an addi-
tional driving aid. This func-
tion is not under any cir-
cumstances intended to
replace the due care and attention
of the driver, who should at all times
be in control of the vehicle.
2.69
SAFE DISTANCE ALERT (2/4)
- press the 5 or 6 control repeatedly to
3
reach the “Distance warning” menu.
Press the switch 7 OK;
- Press the switch 7 OK again to acti-
vate or deactivate the function:
=
function activated
<
function deactivated
4
5
7
6
Activating/deactivating the
Vehicles not fitted with a multimedia
screen
function
- With the vehicle stopped, press the
Vehicles fitted with a multimedia
switch 4 as many times as required
screen 3
to reach the “Vehicle” tab;
To activate or deactivate the function,
- press the 5 or 6 control repeatedly to
refer to the multimedia instructions.
reach the “Settings” menu. Press the
Select “ON” or “OFF”.
switch 7 OK;
- press the 5 or 6 control repeatedly to
reach the “DRIVING ASSIST” menu.
Press the switch 7 OK;
Each time the vehicle is started,
the function continues the mode
saved the last time the engine was
stopped.
2.70
SAFE DISTANCE ALERT (3/4)
- C (orange): the time interval falls be-
8
tween around 1 and 2 seconds (in-
A
sufficient distance between the two
vehicles);
- D (red): the time interval is less than
B
or equal to around one second (very
insufficient distance between the two
The measurement is dis-
vehicles).
played for information: the
If the interval between the two vehi-
system does not carry out
C
cles is less than approximately 0.5 sec-
any action on the vehicle.
onds, the 8 indicator and the D display
This function is not designed for use
will flash in red on the instrument panel
in urban conditions or for a dynamic
D
along with “-.- s”.
driving style (sudden cornering, ac-
Under certain conditions, the time inter-
celeration, braking, etc.), but rather
val may not be displayed:
for stable driving conditions.
Operation
- while cornering;
The function does not interact with
With the function activated, the 8 in-
the braking system.
- when changing lane;
dicator is displayed on the instrument
The radar and camera zones must
panel and informs the driver of the dis-
- if the vehicle in front is sufficiently far
be kept clean and free of any tam-
tance between their vehicle and the ve-
or outside the range of the radar or
pering in order to ensure the proper
hicle in front.
camera.
operation of the system.
- A (grey): function not operational;
Any work carried out in the area
- A (green): no vehicle detected;
where the radar or camera is lo-
cated (repairs, replacements, wind-
- B (green): the time interval is greater
screen and/or bumper modifica-
than or equal to around two seconds
tions, etc.) must be carried out by a
(distance between the two vehicles
qualified professional.
adapted to your speed);
2.71
SAFE DISTANCE ALERT (4/4)
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle.
System servicing/repairs
- In the event of an impact, the radar and/or camera alignment may be changed and its operation may consequently be af-
fected. Deactivate the function and consult an authorised dealer.
- Any work carried out in the area where the radar and/or camera is located (replacements, repairs, windscreen and/or
bumper modifications, etc.) must be carried out by a qualified professional.
Only an authorised dealer is qualified to service the system.
In the event of system disturbance
- obstruction of the windscreen or the bumper (by dirt, glass, snow, condensation, etc.);
- a complex environment (metal bridge, tunnel etc.);
- poor weather conditions (snow, hail, black ice etc.);
- poor visibility (night, fog etc.);
- poor contrast between the vehicle preceding it and the surrounding area (e.g. white vehicle in a snowy area etc.) ;
- being dazzled (glaring sun, lights of vehicles travelling in the opposite direction etc.);
- the road is narrow, winding and undulating (tight bends etc.)
Risk of erroneous false alarms.
2.72
ADVANCED SAFETY (1/17)
The “Advanced Security” system con-
sists of:
1
- active emergency braking;
3
and
- Emergency Lane Keep Assist.
The “Advanced Safety” system uses
information from the camera 1, front
radar 2 and side radars 3.
2
Location of the camera 1
Location of the side radars 3
Make sure the windscreen is not ob-
Ensure that the radar area is not ob-
scured (by dirt, mud, snow, condensa-
structed (by dirt, mud, snow etc.), im-
tion etc.).
pacted or modified (including paintwork
etc.).
Location of the front radar 2
This system provides an
Ensure that the radar area is not ob-
additional driving aid.
structed (by dirt, mud, snow, a badly
This system is not, under
fitted front number plate), impacted,
any circumstances, in-
modified (including painting) or hidden
tended to replace the due care and
by any accessory fitted on the front of
attention of the driver, who should at
the vehicle (on the grille or logo etc.).
all times be in control of the vehicle.
Depending on the sensitivity setting
selected, the “Lane Keep Assist”
function may be used prior to op-
eration of the “Advanced Safety”
system.
2.73
ADVANCED SAFETY (2/17)
- press the 7 or 8 control repeatedly to
4
5
reach the “Advanced Safety” menu
and press 9 OK.
Press the switch 9 OK again to activate
or deactivate the function:
=
function activated
<
function deactivated
Upon deactivation of the system, the
6
7
warning light illuminates or, de-
pending on the vehicle, the
warning light illuminates in yellow on
9
8
the instrument panel.
Activating, deactivating the system
Activating, deactivating the system
When the system is activated, the
from the multimedia screen 4
from the trip computer 5
warning light disappears.
(depending on the vehicle)
- With the vehicle stopped, press the 6
To activate or deactivate the function,
switch as many times as required to
refer to the multimedia instructions.
reach the “Vehicle” tab;
- press the 7 or 8 control repeatedly to
Select “ON” or “OFF”.
reach the “Settings” menu. Press the
switch 9 OK;
- press the 7 or 8 control repeatedly to
reach the “DRIVING ASSIST” menu.
Press the switch 9 OK;
This system is reactivated each time
the ignition is switched on.
2.74
ADVANCED SAFETY (3/17)
The system informs the driver if there
1
is a risk of head-on collision to enable
appropriate emergency manoeuvres
(pressing the brake pedal and/or turn-
ing the steering wheel).
Depending on the reactivity of the
driver, the system can assist with brak-
ing in order to limit damage or prevent
a collision.
2
Active emergency braking
The system uses information from the
radar 2 and the camera 1 to determine
the distance between your vehicle
- from the vehicle ahead in the same
lane;
or
This function is an addi-
This system can apply maximum
- from any oncoming vehicles in the
tional driving aid.
braking to the vehicle until it is
context of a manoeuvre to change
This function is not under
completely stationary if necessary.
direction;
any circumstances in-
or
For safety reasons, always wear
tended to replace the due care
your seat belt when travelling in
- surrounding pedestrians and cy-
and attention of the driver, who
your vehicle and make sure that it
clists.
should at all times be in control of
is loaded so that no items can be
the vehicle.
thrown forward and hit the occu-
pants.
2.75
ADVANCED SAFETY (4/17)
Active emergency braking
Note: if the driver uses the vehicle con-
(continued)
trols (steering wheel, pedals, etc.) the
system may delay certain operations or
Detection of vehicles
not activate.
If driving at a speed between approx-
10
imately 5 mph (8 km/h) and 110 mph
(180 km/h) and there is a risk of colli-
sion with the vehicle in front, with an on-
coming vehicle in the context of a ma-
noeuvre to change direction, or with a
stationary vehicle, the system:
-
warns you of a collision risk:
the
red warning light, or, de-
pending on the vehicle, the dis-
play 10 and the message “Brake”
If active emergency braking has caused
appear on the instrument panel, ac-
the vehicle to stop, the vehicle is kept
companied by a beep.
stationary for a short time. Beyond this
If the driver presses the brake pedal
time limit, the vehicle must be held sta-
and the system still detects a risk of
tionary by the driver keeping their foot
collision, the braking force may be
on the brake pedal.
increased if it is not sufficient to pre-
vent the collision.
-
may trigger braking:
if the driver fails to react following
the alert and collision becomes im-
In the event of emergency manoeu-
minent.
vre, you can stop braking at any
moment by:
- tapping the accelerator pedal;
or
- turning the steering wheel as a
collision avoidance manoeuvre.
2.76
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст