Dacia Pick-Up 1304/1305/1307. Manual — part 93
37
MECHANICAL ELEMENTS CONTROLS
TIGHTNESS CHECKING
The tightness of the servobrake is checked on the vehicle, with the hydraulic circuit
under operation.
Connect the vacuum meter between the
servobrake and the inlet collector by means
of a “ T ” type connector.
The connecting hose of the vacuum
meter shall be as short as possible.
Start the engine and let it idle run for
1min.
Block the air suction hose by means of
the MOT 453 device.
Stop the engine.
Read the indicator.
SERVOBRAKE
If air suction lowers with more than 33 mbar (25 Hg) in 15’period, it means there is a
loss:at the retainer valve - replace the valve or at the servobrake membrane - replace the
servobrake.
Dismount the MOT 453 device.
Dismount the vacuum hose.
Connect the air suction hose to the servobrake.
If the servobrake does not work, but the braking system is working, then the effort on
the brake pedal is increased.
37- 7
MECHANICAL ELEMENTS CONTROLS
37
AIR FILTER REPLACEMENT
D
ISMO UNTING
Dismount the servobrake off the vehicle.
Loosen the lock nut and dismount : the coupling brake and the lock nut.
Remove the old filter, F.
R
EMO UNTING
AIR FILTER - SERVOBRAKE RETAINER VALVE
Mount the new filter.
Mount:
- the lock nut;
- the coupling fork.
Adjust the value L.
Tighten the lock nut on the fork.
Mount the servobrake on the vehicle.
Purge the braking circuit if necessary.
SERVOBRAKE RETAINER VALVE REPLACEMENT
The operation shall be performed without dismounting the servobrake off the vehicle.
D
ISMO UNTING
Disconnect the air suction hose.
Dismount the valve by rotating and then
pulling it.
Dismount the retainer valve gasket.
R
EMO UNTING
Check the state of the retainer valve gasket;
replace it if necessary.
Mount the retainer valve gasket.
Mount the new retainer valve.
Connect the air suction hose.
37 - 8
37
MECHANICAL ELEMENTS CONTROLS
HAND BRAKE
Lever on floor, mechanical controlled, operating on the rear wheels.
T
IGH TENING
MO MENTS
( daNm
)
The attachment screws of the hand brake lever assembly on the floor
1,2
The primary cable tightening nut on swing bar
2
ADJUSTMENT
With rear wheels suspended and hand brake lever released ,tighten the castle nut M
until the shoes gaskets come lightly into contact with the brake drum.
Tighten the lock nut N at the required moment.
The adjustment shall be performed so that is insuring a hand brake lever stroke of min.7
teeth until the blocking of all wheels.
The adjustment shall be performed anytime the shoes wear is requiring it.
The hand brake adjustment shall be performed only after the rear brake adjustment.
37 - 9
M
N
MECHANICAL ELEMENTS CONTROLS
37
HANDBRAKE CONTROL LEVEL
D
ISMO UNTING
Disconnect the battery.
Lift the vehicle by means of an elevator.
Release the hand brake.
Disconnect the primary cable from the
rocking joint.
Dismount the hand brake ornament case.
Dismount the screws that attach the hand
brake lever to the floor.
Release the hand brake lever.
Dismount:
- the locking ring of the primary cable fork
shaft;
- the primary fork shaft;
- the hand brake lever.
R
EMO UNTING
Grease the primary cable fork shaft with special MoS2 grease.
Connect the primary cable.
Mount the hand brake lever.
Mount the hand brake ornament case.
Adjust the hand brake.
Get down the vehicle on ground.
Connect the battery.
37 - 10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст