Renault Master (2022 year). Manual in english — page 14
FUSES (4/5)
5
3
6
4
C
2
C
7
4
Refitting fuse box C
Screw the four screws 4 to ensure that
Position coolant reservoir 3, then screw
unit 5 is completely sealed.
bolt 2.
Clip the mountings 7, then clip mount-
ing 6.
Check that no water or dust enters
unit 5 when it is being removed/re-
fitted.
5.30
FUSES (5/5)
Allocation of fuses (DEPENDING ON THE EQUIPMENT LEVEL)
Symbol
Allocation
Symbol
Allocation
Right-hand main beam
d
De-icing
P
headlight
Heating and air condition-
t
n
ABS
ing system
Right-hand dipped beam
T
f
Windscreen wiper
headlight
Left-hand dipped beam
L
headlight
G
Fog light
Left-hand main beam
Q
headlight
5.31
BATTERY: troubleshooting (1/2)
To avoid all risk of sparks:
Connecting a battery charger
-
Ensure that any consumers (cour-
The battery charger must be com-
tesy lights, etc.) are switched off
patible with a battery with nominal
before disconnecting or reconnect-
voltage of 12 volts.
ing the battery;
Do not disconnect the battery when the
-
when charging, stop the charger
engine is running. Follow the instruc-
before connecting or disconnecting
tions given by the manufacturer of
the battery;
the battery charger you are using.
-
to avoid creating a short circuit be-
tween the terminals, do not place
When many accessories are fitted to
Handle the battery with care
metal objects on the battery;
the vehicle, have them connected to
as it contains sulphuric acid,
-
always wait at least one minute after
the + after ignition feed.
which must not come into
the engine has been switched off
contact with eyes or skin. If
before disconnecting a battery;
it does, wash the affected area with
-
make sure that you reconnect the
plenty of cold water. If necessary,
battery terminals after refitting.
consult a doctor.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
Special procedures may be
Please note when working close to
required to charge some
the engine that it may be hot. In ad-
batteries. Contact your ap-
dition, the engine cooling fan may
proved dealer.
Avoid all risk of sparks which may
start at any moment. The
cause an immediate explosion, and
warning light in the engine compart-
charge the battery in a well venti-
ment reminds you of this.
Before
carrying
out
any
lated area.
Risk of injury.
action in the engine com-
Risk of serious injury.
partment, you must switch
off the ignition. ➥ 2.3.
Risk of injury.
5.32
BATTERY: troubleshooting (2/2)
Starting the vehicle using the
battery from another vehicle
4
If you have to use the battery from an-
other vehicle to start, obtain suitable
jump leads (with a large cross section)
from an approved dealer or, if you al-
A
ready have jump leads, ensure that
3
B
they are in perfect condition.
The two batteries must have an iden-
tical nominal voltage of 12 volts. The
battery supplying the current should
have a capacity (amp-hours, Ah) which
is at least the same as that of the dis-
charged battery.
2
1
Ensure that there is no risk of contact
Attach the positive lead (+) A to termi-
between the two vehicles (risk of short
nal 3, then to terminal 2 (+) of the bat-
circuiting when the positive terminals
tery supplying the current.
are connected). Switch off your vehicle
ignition.
Attach negative lead (-) B to terminal 1
(-) of the battery supplying the current,
Start the engine of the vehicle supply-
then to earth 4 (-).
ing the current and run it at a moderate
4
speed.
Start the engine, as soon as it is run-
ning disconnect cables A and B in re-
verse order (4 - 1 -2 -3).
3
Check that there is no contact between leads A and B and that the posi-
tive lead A is not touching any metal parts on the vehicle supplying the
current.
Risk of injury and/or damage to the vehicle.
5.33
RADIO FREQUENCY REMOTE CONTROL: battery (1/2)
A
3
2
2
1
1
Replacing the battery
Special feature of key A
Open the case at slot 1 using a flat-
Undo screw 3 to remove the remote
blade screwdriver or similar and re-
control cover.
place the battery 2, observing the type
and polarity shown on the back of the
cover.
Note: It is not advisable to touch the
electrical circuit in the key cover when
replacing the battery.
When they need to be re-
placed, be sure to use
the same or equivalent
The batteries are available from ap-
type of battery (consult an
proved Dealers, and their service
Approved Dealer).
life approximately two years. Check
When refitting, ensure that the cover
that there is no dye on the battery:
is correctly clipped on and the screw
risk of an incorrect electrical con-
tightened.
tact.
5.34
RADIO FREQUENCY REMOTE CONTROL: battery (2/2)
Operating faults
If the battery is too weak to ensure cor-
rect operation, you will still be able to
start and lock/unlock the vehicle
➥ 1.10.
Do not throw away your used bat-
Precautions relating to
teries; give them to an organisation
batteries:
responsible for collecting and recy-
- keep (new or used) bat-
cling batteries.
teries out of reach of chil-
dren;
- do not swallow batteries;
When replacing:
Risk of chemical burns which
- make sure that the batter-
may lead to death.
ies are correctly inserted.
- if ingested or inserted into any
part of the body, consult a doctor
Risk of explosion.
as soon as possible.
- if the flap does not close cor-
rectly, do not use and keep out of
reach of children.
5.35
HANDS-FREE ACCESS TRANSMITTER, RECEIVER: battery (1/2)
2
1
Replacing the battery
Replace battery 2 according to the di-
rection marked on the cover.
Use a coin to open the unit via slot 1.
Note: it is not advisable to touch the
electronic circuit in the cover when re-
placing the battery.
When they need to be re-
placed, be sure to use
The batteries are available from ap-
the same or equivalent
proved Dealers, and their service
type of battery (consult an
life approximately two years.
Approved Dealer).
Check that there is no dye on the
battery: risk of an incorrect electri-
When refitting, ensure that the cover
cal contact.
is correctly clipped into place.
5.36
HANDS-FREE ACCESS TRANSMITTER, RECEIVER: battery (2/2)
Operating faults
If the battery is too weak to ensure cor-
rect operation, you will still be able to
lock/unlock the vehicle➥ 1.10.
Do not throw away your used bat-
Precautions relating to
teries; give them to an organisation
batteries:
responsible for collecting and recy-
- keep (new or used) bat-
cling batteries.
teries out of reach of chil-
dren;
- do not swallow batteries;
When replacing:
Risk of chemical burns which
- make sure that the batter-
may lead to death.
ies are correctly inserted.
- if ingested or inserted into any
part of the body, consult a doctor
Risk of explosion.
as soon as possible.
- if the flap does not close cor-
rectly, do not use and keep out of
reach of children.
5.37
WIPER BLADES
Check the condition of the wiper
blades. You are responsible for their
2
3
service life:
4
-
clean the blades and the wind-
screen regularly with soapy
5
water;
-
do not use them when the wind-
screen is dry;
-
free them from the windscreen
B
1
when they have not been used
A
for a long time.
To access the wiper blades, stand on
-
press tab 3 and slide the wiper blade
step 1.
downwards to release hook 5 from
the wiper arm;
- In frosty weather, make
Note: the step may be slippery.
sure that the wiper blades
-
slide the blade A then lift it B to re-
are not stuck by ice
(to
lease it.
Replacing windscreen wiper
avoid the risk of the motor
overheating).
blades 2
Refitting
-
Check the condition of the wiper
With the ignition on and the engine
To refit the wiper blade, proceed in the
blades.
switched off, lower the windscreen
reverse order to removal. Make sure
Replace the wiper blades as soon
wiper stalk fully: the wipers stop in a
that the blade is correctly locked in po-
as they begin to lose efficiency
position away from the bonnet.
sition.
(approximately once a year).
– Lift wiper arm 4;
Whilst changing the blade, take care
- move the blade into a horizontal po-
not to drop the arm onto the window
sition;
after it has been removed as this
may break the window.
5.38
TOWING: breakdown (1/2)
The steering wheel must not be
Towing a vehicle with a
locked and the ignition key must
sequential gearbox
be in
“Mˮ position
(ignition on)
If the gearbox is stuck in a gear:
to enable the signalling to operate
(brake lights, hazard warning lights
- switch on the ignition;
etc.) At night the vehicle must have
- with the brake pedal pressed, select
its lights on.
neutral;
Unhitch the trailer, etc., if one is
- check that the gearbox is in neutral
being towed.
(by pushing the vehicle for example).
You must observe the towing regu-
If you cannot find neutral you must tow
lations which apply in the country in
the vehicle with the front wheels raised.
which you are driving: do not exceed
the towing weight for your vehicle.
The vehicle should always be towed
with the ignition switched off.
Contact an approved dealer.
- Use a rigid towing bar.
If a rope or cable is used
(where the law allows this),
the vehicle being towed
must be able to brake.
-
A vehicle must not be towed if it is
not fit to be driven.
-
Avoid accelerating or braking
Do not remove the key from
suddenly when towing, as this
the ignition when the vehi-
may result in damage being
cle is being towed.
caused to the vehicle.
-
When towing a vehicle, it is ad-
visable not to exceed 15 mph
When the engine is
(25 km/h).
stopped, steering and brak-
ing assistance are not oper-
ational.
5.39
TOWING: breakdown (2/2)
2
3
1
4
Only use:
Accessing towing eye 3
Move the driver’s seat forward and tilt
- At the rear left, towing point 1.
the seatback in order to access the tool
- At the front, towing hitch 3 (from
kit ➥ 5.4.
Ensure that the towing eye
the tool kit) and towing point 2.
is bolted correctly.
Accessing front towing point 2
These towing points may only be used
Risk of losing the towed
Unclip cover 4 by inserting a flat-blade
for pulling the vehicle, never for lifting it
object.
screwdriver or similar under the cover.
either directly or indirectly.
Screw-in the towing ring 3 by hand
When storing the tools,
as far as it will go, then tighten it fully
ensure that they are cor-
using the wheelbrace stored in the tool
rectly placed in their original
kit ➥ 5.4.
positions in the toolbox and
store the toolbox under the driver’s
seat. Do not leave the tools unse-
cured inside the vehicle as they may
come loose under braking.
5.40
FITTING THE RADIO
1
2
If your vehicle is not fitted with an audio
system, one can be fitted and locations
have been provided for:
- radio 1;
- front speakers 2 (depending on the
vehicle).
To install any equipment, please con-
sult an approved dealer.
-
In all cases, it is very important to follow the manufacturer’s instructions care-
fully.
–
The specifications of the brackets and wires (available from our network) vary
Radio location 1
depending on the equipment level of your vehicle and the type of radio.
Unclip the blanking cover. The aerial, +
and - supply and speaker wire connec-
Consult an approved Dealer to find out the correct part number.
tions are located behind it.
-
No work may be carried out on the vehicle’s electrical or radio circuits, except
by approved dealers: an incorrectly connected system may result in damage
being caused to the electrical equipment and/or the components connected to
it.
5.41
ACCESSORIES
Electrical and electronic accessories
Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po-
sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer.
Connect accessories with a maximum power of 120 Watts only. Fire hazard. When several accessory sockets are
used at the same time, the total power of the connected accessories must not exceed 180 watts.
No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected
system may result in damage being caused to the electrical equipment and/or the components connected to it.
If the vehicle is fitted with any aftermarket electrical equipment, make sure that the installation is correctly protected by a fuse.
Establish the rating and position of this fuse.
Using the diagnostic socket
The use of electronic accessories on the diagnostic socket may cause serious disturbance to the vehicle’s electronic systems.
For your safety we recommend that you use only electronic accessories approved by the manufacturer, consult an Approved
Dealer. Serious accident risk.
Use of transmitting/receiving devices (telephones, CB equipment etc.).
Telephones and CB equipment with integrated aerials may cause interference to the electronic systems originally fitted to the
vehicle: it is advisable only to use equipment with an external aerial. Furthermore, we remind you of the need to conform
to the legislation in force concerning the use of such equipment.
Fitting aftermarket accessories
If you wish to install accessories on the vehicle: please contact an authorised dealer. Also, to ensure the correct operation of
your vehicle, and to avoid any risk to your safety, we recommend that you use only accessories specifically designed for your
vehicle, which are the only accessories for which the manufacturer will provide a warranty.
If you are using an anti-theft device, only attach it to the brake pedal.
Obstructions to the driver
On the driver’s side, only use mats suitable for the vehicle, attached with the pre-fitted components, and check the fitting regu-
larly. Do not lay one mat on top of another. There is a risk of wedging the pedals.
5.42
OPERATING FAULTS (1/7)
The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact
an approved dealer as soon as possible.
Using the remote control
POSSIBLE CAUSES
ACTION REQUIRED
The remote control does not lock or The remote control battery is flat.
Use the emergency key.
unlock the doors.
Use of appliances operating on the same
Stop using the devices or use the key.
frequency as the remote control (mobile
phone, etc.).
Vehicle located in a high electromagnetic
Replace the battery. You will still be able to
radiation zone.
lock, unlock, and start your vehicle ➥ 1.10
and ➥ 2.3.
Discharged battery.
The vehicle is started.
With the engine running, the key’s locking/
unlocking device is blocked. Turn off the
ignition.
Desynchronisation of the remote control.
Unlock the driver’s door using the key in
the door lock, then start the engine ➥ 2.3
to synchronise the remote control.
5.43
OPERATING FAULTS (2/7)
The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact
an approved dealer as soon as possible.
The starter is activated
POSSIBLE CAUSES
WHAT TO DO
Warning lights dim or fail to come on;
Battery terminals disconnected,
Contact an approved Dealer.
the starter does not run.
oxidised or incorrectly secured.
Battery discharged or worn.
Connect another battery to the faulty bat-
tery ➥ 5.32 or replace the battery if neces-
sary.
Do not push the vehicle if the steering
column is locked.
The engine will not start.
Starting conditions are not fulfilled.
➥ 2.3
The steering column remains locked.
Steering wheel locked.
To unlock, turn the key and the steering
wheel. ➥ 2.2.
5.44
OPERATING FAULTS (3/7)
On the road
POSSIBLE CAUSES
WHAT TO DO
Vibrations.
Tyres not inflated to the correct pres-
Check the tyre pressures: if this is not the
sure, incorrectly balanced or dam-
problem, have them checked by an ap-
aged.
proved dealer.
Coolant boiling in the coolant reservoir.
Mechanical fault: damaged cylinder
Stop the engine.
head gasket.
Contact an approved Dealer.
Smoke under the bonnet.
Short circuit or cooling system leak.
Stop, switch off the ignition, stand away
from the vehicle and contact an approved
dealer.
The oil pressure warning light comes
on:
while cornering or braking
The level is too low.
Top up the engine oil ➥ 4.6.
is slow to go out or remains lit under
Loss of oil pressure.
Stop the vehicle and contact an approved
acceleration
Dealer.
White smoke from the exhaust.
This is not necessarily a fault. Smoke
➥ 2.7
may be caused by regeneration of
the particle filter.
5.45
OPERATING FAULTS (4/7)
On the road
POSSIBLE CAUSES
WHAT TO DO
Smoke under the vehicle when start-
This is not necessarily a fault. The
ing the heating.
smoke may come from the heater.
If this happens, the smoke will grad-
ually disappear once the passen-
ger compartment temperature has
reached the appropriate level.
Steering becomes heavy.
Assistance overheating.
Drive carefully at reduced speed, be aware
of the level of force in the steering wheel
Fault with the electric assistance
needed to turn the wheels. Consult an ap-
motor.
proved dealer
Fault in the assistance system.
The engine is overheating. The cool-
Engine cooling fan not working.
Stop the vehicle, switch off the engine and
ant temperature warning light and the
contact an approved Dealer.
STOP warning light come on.
Coolant leaks.
Check the coolant reservoir: it should con-
tain fluid. If there is no coolant, consult an
approved Dealer as soon as possible.
Radiator: If there is a significant lack of coolant, remember that it must never be topped up using cold coolant while
the engine is very warm. After any procedure on the vehicle which has involved even partial draining of the cooling
system, it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved
by our Technical Department may be used for this purpose.
5.46
OPERATING FAULTS (5/7)
Stopped
POSSIBLE CAUSES
WHAT TO DO
The engine cooling fan starts to run
This is not necessarily a fault. The
after the ignition is switched off.
engine cooling fan group may start
to run in order to regulate the engine
temperature. This operation may last
several minutes after the engine is
switched off.
The engine cooling fan runs for more
Consult an approved dealer.
than 10 minutes after the engine is
switched off.
5.47
OPERATING FAULTS (6/7)
Electrical equipment
POSSIBLE CAUSES
WHAT TO DO
The wipers do not work.
Wiper blades stuck.
Free the blades before using the wipers.
Faulty electrical circuit.
Consult an approved dealer.
Fuse damaged.
Replace the fuse or have it replaced
➥ 5.27.
The wiper does not stop.
Faulty electrical controls.
Consult an approved dealer.
Direction indicators flashing more
Blown bulb.
➥ 5.21 ➥ 5.23 ➥ 5.24
quickly.
Fuse damaged.
Replace the fuse or have it replaced
➥ 5.27.
The direction indicators do not work.
Faulty electrical circuit or control.
Consult an approved dealer.
Fuse damaged.
Replace the fuse or have it replaced
➥ 5.27.
5.48
OPERATING FAULTS (7/7)
Electrical equipment
POSSIBLE CAUSES
WHAT TO DO
The lights do not come on or go off.
Faulty electrical circuit or control.
Consult an approved dealer.
Fuse damaged.
Replace the fuse or have it replaced
➥ 5.27.
Traces of condensation in the head-
Traces of condensation may be a nat-
lights or rear lights.
ural phenomenon caused by varia-
tions in temperature and humidity.
In this situation, these traces soon dis-
appear when the lights are switched
on.
5.49
Section 6: Technical specifications
Vehicle identification plates
6.2
Technical information for the emergency services
6.4
Engine identification
6.5
Engine specifications
6.6
Dimensions
6.7
Weights
6.9
Replacement parts and repairs
6.10
Service sheets
6.11
Anticorrosion check
6.17
6.1
VEHICLE IDENTIFICATION PLATES (1/2)
A
1
2
3
4
A
5
10
6
9
7
8
The information shown on the ve-
5
GTW (Gross train weight: vehicle
hicle identification plate should be
fully loaded, with trailer).
quoted on all correspondence or
6
MPAW (Maximim Permissible
orders.
Weight) for front axle.
7
MPAW on rear axle.
Vehicle identification plate A
8
Reserved for related or additional
1
Manufacturer name.
entries.
2
EC design number or approval
9
Not used.
number.
10
Paint reference (colour code).
3
Identification number.
Depending on the vehicle, this
information is also given on
marking B.
4
MAM
(Maximum Authorised
Mass).
6.2
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст