Daewoo Nubira. Manual — part 23
DOORS 9P – 7
DAEWOO V–121 BL4
Step
No
Yes
Value(s)
Action
20
Repair the open WHT wire.
Is the repair complete ?
System OK
21
Repair the open lock relay.
Is the repair complete ?
System OK
POWER WINDOWS (FRONT AND REAR)
Power Windows Do Not Operate
Step
Action
Value(s)
Yes
No
1
1. Make sure the window lock switch on the driv-
er
'
s side door is not engaged. necessary.
2. Test each of the power windows.
Does any power window operate ?
Go toStep 7
Go toStep 2
2
1. At the driver
'
s side door, remove the power
window switch retaining screw.
2. Lift up the power window switch to expose the
connector.
3. Turn the ignition ON.
4. Check the voltage at terminal 10 (ORN) of the
power window switch.
Is the voltage equal to the specified value ?
11––14 v
Go toStep 4
Go toStep 3
3
Repair the open power supply circuit to the driver
'
s
side door power window switch.
Is the repair complete
System OK
4
Use an ohmmeter to check the continuity between
ground and terminal 4 (BLK) of the driver
'
s side door
power window switch connector.
Is the continuity equal to the specified value ?
[
0
W
Go toStep 6
Go toStep 5
5
Repair the open circuit between ground and terminal
4 (BLK) of the driver
'
s side door power window
switch.
Is the repair complete
System OK
6
Replace the driver
'
s side power window switch.
Is the repair complete
System OK
7
1. At the door with the inoperative power window,
remove the door trim panel.
2. connect a fused jumper wire to the positive bat-
tery terminal.
3. Connect another jumper wire to the negative
battery teminal.
4. Disconnect the two––wire connector between
the window motor and the door harness.
5. Connect the negative jumper wire to one of the
terminals of the two––wire connector.
6. Touch the positive jumper wire to the other ter-
minal of the two––wire connector.
Does the window move up when the motor is pow-
ered directly by the battery, and down when the
jumper connections are reversed ?
Go toStep 9
Go toStep 8
8
Replace the window motor.
Is the repair complete
System OK
9P – 8
I
DOORS
DAEWOO V–121 BL4
Step
No
Yes
Value(s)
Action
9
Check the operation of the windows.
Is the driver
'
s side window the one that is inoperative
?
Go toStep 10
Go toStep 11
10
Replace the driver
'
s side door power window switch.
Is the repair complete
System OK
11
1. Make sure the window lock switch on the driv-
er
'
s side door is not engaged.
2. Turn the ignition ON.
3. Backprobe to check the voltage at terminal 5
(DK BLU) of the driver
'
s side door power win-
dow switch.
Is the voltage equal to the specified value ?
11––14 v
Go toStep 12
Go toStep 10
12
1. Make sure the window lock switch on the driv-
er
'
s side door is not engaged.
2. Turn the ignition ON.
3. Check the voltage at terminal 2 (PNK) of the
window switch connector for the inoperative
window.
Is the voltage equal to the specified value ?
11––14 v
Go toStep 14
Go toStep 13
13
Repair the open wire between the terminal 2 of the
window switch and the driver
'
s side door power win-
dow switch.
Is the repair complete
System OK
14
1. At the inoperative window switch, use an ohm-
meter to check the continuity between ground
and terminal 4.
2. At the inoperative window switch, use an ohm-
meter to check the continuity between ground
and terminal 1.
Are the continuities equal to the specified value ?
11––14 v
Go toStep 15
Go toStep 16
15
Replace the power window switch.
Is the repair complete
System OK
16
If one of the window switch wires tested in Step 14
does not show continuity with ground, use an ohm-
meter to test the continuity of that wire between the
window switch and the driver
'
s side door power win-
dow switch.
Is the continuity equal to the specified value ?
[
0
W
Go toStep 17
Go toStep 18
17
Replace the window switch for the inoperative win-
dow.
Is the repair complete ?
System OK
18
Repair the open circuit between the window switch
and the driver
'
s side power window switch.
Is the continuity equal to the specified value ?
[
0
W
Go toStep 21
Go toStep 20
DOORS 9P – 9
DAEWOO V–121 BL4
MAINTENANCE AND REPAIR
ON–VEHICLE SERVICE
FRONT DOOR GLASS RUN
Removal Procedure
1. Remove the outside rearview mirror. Refer to Sec-
tion 9L, Glass and Mirrors.
2. Remove the front door glass. Refer to Section 9L,
Glass and Mirrors.
3. Remove the glass run.
Installation Procedure
1. Install the glass run.
2. Install the front door glass. Refer to Section 9L,
Glass and Mirrors.
3. Install the outside rearview mirror. Refer to Section
9L, Glass and Mirrors.
REAR DOOR GLASS RUN
Removal Procedure
1. Remove the rear door glass. Refer to Section 9L,
Glass and Mirrors.
2. Remove the interior garnish molding.
3. Remove the screws and the exterior garnish mold-
ing.
9P – 10
I
DOORS
DAEWOO V–121 BL4
4. Remove the glass run.
Installation Procedure
1. Install the glass run.
Notice : Dissimilar metals in direct contact with each other
may corrode rapidly. Make sure to use the correct fasten-
ers to prevent premature corrosion.
2. Install the exterior garnish molding with the screws.
Tighten
Tighten the rear door exterior garnish molding screws
to 1.5 N
S
m (13 lb–in).
3. Install the interior garnish molding.
4. Install the rear door glass. Refer to Section 9L,
Glass and Mirrors.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст