Daewoo Nubira. Manual — part 6

9T – 10

I

REMOTE KEYLESS ENTRY AND ANTI–THEFT SYSTEM

DAEWOO V–121 BL4

PASSWORD PROGRAMMING

If a transmitter is lost or damaged, the control module/re-
ceiver must be re–programmed to communicate with a
new transmitter. The passwords recorded in the control
module/receiver should not be deleted when power is off
in the control module/receiver.

Each control module/receiver should be able to record five
passwords. The following method is used to record new
passwords in the control module/receiver:
1. Connect the scan tool to the assembly line diagnos-

tic link (ALDL) connector.

2. Turn the ignition ON.
3. Delete the current passwords.
4. Send the programming mode message to the con-

trol module/receiver.

5. Press any button of the transmitter to generate a

data code including a password which will be re-
corded by the control module/receiver. The control
module/receiver sends a response message to the
scan tool to indicate that the first password has
been recorded.

6. Press any button of the transmitter to generate a

data code including a password which will be re-
corded by the control module/receiver. The control
module/receiver sends a response message to the
scan tool to indicate that the second password has
been recorded.

7. Press any button of the transmitter three more

times until the control module/receiver has re-
sponded that the third, fourth, and fifth passwords
have been recorded.

8. Turn the ignition OFF.
9. Disconnect the scan tool.
The control module/receiver automatically leaves the pro-
gramming mode and switches to the normal operating
mode when either of the following conditions occurs:

S

The scan tool is disconnected from the ALDL.

S

Five passwords are recorded in the control module/
receiver.

REMOTE KEYLESS ENTRY AND ANTI–THEFT SYSTEM 9T – 11

DAEWOO V–121 BL4

GENERAL DESCRIPTION

AND SYSTEM OPERATION

REMOTE KEYLESS ENTRY AND
ANTI–THEFT SYSTEM

The remote keyless entry and anti–theft system can per-
form the following functions:

S

Remotely lock and unlock the vehicle doors with a
hand–held high–frequency transmitter.

S

Sense intrusion into the vehicle through the doors,
the trunk, or the hood.

S

Activate a warning to signal an intrusion.

S

Help the driver find the vehicle in a parking area.

S

Automatically

re–lock the doors if a door or the

trunk is not opened within 30 seconds after the ve-
hicle has been unlocked by the remote keyless
entry.

S

Communicate serial data to a scan tool to help
diagnose system faults.

The remote keyless entry and anti–theft system consists
of the following components:

S

Keyless entry and anti–theft control module/receiv-
er.

S

Security

indicator.

S

Rear deck lid open switch.

S

Rear deck lid tamper switch.

S

Front door tamper switches.

S

Door open switches.

S

Central locking unit.

S

Flashing turn signal lamps.

S

Siren.

S

Hood open switch.

REMOTE LOCKING AND UNLOCKING

The hand–held transmitter locks and unlocks the vehicle
doors by sending radio waves to the control module/re-
ceiver in the vehicle. The effective range of the transmitter
varies between 5 and 10 meters (approximately 16 to 32
feet), depending on whether or not objects such as other
vehicles are blocking the path of the radio waves.

The transmitter has a LOCK button and an UNLOCK but-
ton which only function when the ignition is OFF. Pressing
the UNLOCK button has the following effects:

S

The doors are unlocked.

S

The turn signal lamps flash twice.

S

The control module is disarmed.

Pressing the LOCK button has the following effects:

S

The doors are locked.

S

The turn signal lamps flash once.

S

The control module is armed.

The transmitter has a replaceable battery. The battery is
designed to last at least three years before replacement
is necessary.

SECURITY INDICATOR

There is a security indicator on the instrument panel. After
the LOCK button of the transmitter is pressed, the module
is placed in the armed mode, and the security indicator
flashes. The security indicator turns ON for 0.1 second
and OFF for 0.7 second. It then flashes at that frequency
until the control module/receiver is disarmed. If the vehicle
is equipped with an immobilizer, the security indicator is
connected to the immobilizer system instead of the key-
less entry/anti–– theft system.

INTRUSION SENSING

The anti–theft function is armed if the transmitter sends
the LOCK message to the control module/receiver when
the ignition is OFF.

When the hood, the door, or the rear deck lid is opened,
the hood open switch, the door open switch, or the trunk
open switch will change its input to ground. The alarm will
be activated if the hood open sensor, the door open sen-
sor, or the trunk open sensor changes its input to ground
before either of the following conditions occurs:

S

An UNLOCK message is received from the trans-
mitter.

S

The front door tamper switch or the rear deck lid
tamper switch indicates key operation by changing
its input to ground.

The alarm also will be activated if the ignition input is
changed to battery voltage before either of the following
conditions occurs:

S

An UNLOCK message is received from the trans-
mitter.

S

The front door tamper switch or the rear deck lid
tamper switch indicates key operation by changing
its input to ground.

SIREN

The remote keyless entry system is armed when the
LOCK message is received from the transmitter when the
ignition is OFF. When the system is armed, it will activate
the siren and flash the turn signals for 28 seconds if any
of the following conditions occurs:

S

A door is opened without using the key (front door
open switch input is changed to ground).

S

The rear deck lid is opened without using the key
trunk open switch input is changed to ground).

S

The hood is opened while the anti–theft system is
armed (hood open switch input is changed to
ground).

S

The ignition switch input is changed to battery volt-
age.

The siren is disarmed when any of the following conditions
occurs:

9T – 12

I

REMOTE KEYLESS ENTRY AND ANTI–THEFT SYSTEM

DAEWOO V–121 BL4

S

The door is opened with the key.

S

The rear deck lid is opened with the key.

S

The UNLOCK button or the LOCK button on the
remote transmitter is pressed within 2 seconds of
the beginning of the alarm. If the UNLOCK button
or the LOCK button is not pressed within 2 seconds
of the beginning of the alarm, the transmitter will
not stop the alarm.

VEHICLE LOCATOR

The remote keyless entry system assists the driver in lo-
cating the vehicle. When the vehicle is unlocked with the
remote control, the turn signals flash twice to indicate the
location of the vehicle. The duration of the flashes and the
length of time between flashes is used to indicate certain
vehicle conditions. Refer to ”Fault or Alarm Indication” in
this section.

AUTOLOCKING (SAFETY LOCK)

The remote keyless entry system features an autolocking
control. If the doors are unlocked with the remote transmit-
ter when the control module/receiver is in the armed
mode, the doors are automatically re–locked after 30 sec-
onds unless any of the following events occur:

S

The door is opened.

S

The ignition switch is turned ON.

S

The rear deck lid is opened.

S

The hood is opened.

CONTROL MODULE/RECEIVER

The remote keyless entry control module/receiver is con-
tained in the floor console. The module/receiver pro-
cesses signals from the remote transmitter and the intru-
sion sensors, and it activates the alarm if an intrusion is
detected. The control module/receiver also has a selfdiag-
nostic function which will display trouble codes. In order to
display trouble codes, a scan tool must be connected to
the assembly line diagnostic link (ALDL) connector.

The control module/receiver will not communicate with
transmitters from other vehicles because there are over
four billion possible electronic password combinations,

and passwords are not duplicated. The control module/ re-
ceiver has an attached antenna to detect signals from the
transmitter.

FAULT OR ALARM INDICATION

When the UNLOCK button on the remote transmitter is
pressed, the control module/receiver will flash the parking
lamps to indicate information about the remote keyless
entry and anti–theft system.

Normal Condition: If there has not been an intrusion, and
no fault has been detected, the control module/receiver
will signal a normal condition when the UNLOCK button is
pressed. The parking lamps will flash twice for 0.5 second,
with a 0.5 second pause between flashes.

Fault Indication: If there is a fault in the remote keyless
entry and anti–theft system, the control module/receiver
will signal the fault when the UNLOCK button is pressed.
The parking lamps will flash twice for 1 second, with a 0.5
second pause between flashes.

Alarm Indication: If there has been an intrusion since the
last time the LOCK button was pressed, the control mod-
ule/receiver will signal that there has been an intrusion
when the UNLOCK button is pressed. The parking lamps
will flash twice for 0.5 second, with a 1.5 second pause be-
tween flashes.

Alarm and fault information in the control module/receiver
will be erased the next time the controlmodule/receiver en-
ters the armed condition after receiving a LOCK message
from the transmitter.

PANIC BUTTON

In addition to the LOCK and UNLOCK buttons on the
transmitter, there is the panic button. This button is used
to activate the siren if a threatening situation occurs while
the driver is approaching the vehicle. If the panic button is
held down for 2 seconds, the siren will be activated for 30
seconds, and the parking lights will flash during that time.

TECHNICAL SERVICE BULLETIN

TECHNICAL SERVICE BULLETIN

Description:

Reference:

Prod. Dates:

Bulletin No.:

Model(s):

Date:

VIN Range:

Group:

General Manager
Service Manager

Technician(s)
Service Advisor

Body Shop Manager
Parts Manager

Circulate To:

√

√
√

√
√

√

TSB-003-01

All

May 18, 2001

All

Remote Keyless Entry Transmitter
Programming

Body

N/A

All

Remote Keyless Entry Transmitter Programming Information

The Daewoo Remote Keyless Entry System allows for the use of as many as five (5)
transmitters for each vehicle. Replacement Remote Keyless Entry System Transmitters must
first be programmed to a specific vehicle using the Scan 100 Scan Tool. This process is
completed using serial data communication between the Scan 100 Scan Tool and the Remote
Keyless Entry Control Unit and is the only method available for programming Transmitters.

Note: All Transmitters for a specific vehicle must be programmed at the same time.

Once the programming function of the Remote Keyless Entry System is
activated, any Transmitter (existing or new) that is not programmed (or
reprogrammed) during the programming procedure will no longer operate the
Remote Keyless Entry System of that vehicle.

This Technical Service Bulletin provides information concerning the programming procedure
for the Remote Keyless Entry Transmitter(s).

REMOTE KEYLESS ENTRY TRANSMITTER PROGRAMMING PROCEDURE:

Note:

Ensure that the doors, hood and trunk / rear hatch are closed prior to starting
the programming procedure.

1.

Connect the Scan 100 Scan Tool to the Data Link Connector (DLC).

2.

Turn the Scan 100 Scan Tool “ON” by pressing the “POWER” Button, then wait for the
MAIN MENU screen to be displayed.

3.

From the MAIN MENU screen, select “Diagnostics” by pressing #1 on the Key Pad.

4.

From the MODEL YEAR screen, select the appropriate model year of the specific vehicle
by either scrolling down to the year and pressing “ENTER”, or by pressing the respective
item number on the Key Pad.

5.

From the VEHICLE TYPE screen, select the specific vehicle model by either scrolling
down to the model name and pressing “ENTER”, or by pressing the respective item
number on the Key Pad.

6.

From the SYSTEM SELECTION MENU screen, select “Body” by pressing #2 on the Key
Pad.

7.

From the BODY SELECTION MENU screen, select “Coding” by pressing #2 on the Key
Pad.