Daewoo Musso. Manual — part 195
M162 ENGINE INTAKE & EXHAUST 1G1-9
EXHAUST MANIFOLD
Preceding Work : Removal of air cleaner
1 Nut . . . . . . . . . . . . . ... 36-44 Nm
2 Gasket . . . . . . . . . . . . ... Replace
3 Exhaust Manifold
1G1-10 M162 ENGINE INTAKE & EXHAUST
Tools Required
103 589 01 39 00 Caulking Bolt
Removal & Installation Procedure
1. Remove the flange bolt from the exhaust manifold, and
disconnect the front exhaust pipe.
Installation Notice
Notice
Check for nut damages and replace the nut if necessary.
2. Remove the 23 nuts (1) from the stud bolt, and remove the
exhaust manifold.
Installation Notice
3. Replace the gasket (2).
4. Installation is reverse order of the removal.
Replacement of Rivet Nut
1. Pull out the rivet nut from the connecting point of the exhaust
manifold and the exhaust pipe using a proper bolt (arrow).
2. Insert a new rivet nut into the exhaust manifold hole, and
tighten with a special tool (Caulking Bolt).
Installation Notice
Caulking Bolt 103 589 01 39 00
Tightening Torque
30 Nm
Tightening Torque
26 - 34 Nm
Tightening Torque
30 Nm
M162 ENGINE INTAKE & EXHAUST 1G1-11
Removal and Installation of Exhaust Line
1 Exhaust Manifold
2 Rivet Nut
3 Bolt . . . . . . . . . . . . . . ... 30 Nm
4 Front Pipe
5 Oxygen Sensor
6 Bolt . . . . . . . . . . . . . .. 28-47 Nm
7 Rubber Pad
8 Catalytic Converter
9 Gasket . . . . . . . . . . . . ... Replace
10 Nut
11 Gasket . . . . . . . . . . . . ... Replace
12 Rubber Pad
13 Nut . . . . . . . . . . . . . ... 28-47 Nm
14 Center Muffler
15 Rubber Pad
16 Tail Muffler
17 Gasket . . . . . . . . . . . . ... Replace
18 Nut . . . . . . . . . . . . . ... 28-47 Nm
SECTION 1G2
M161 ENGINE INTAKE & EXHAUST
TABLE OF CONTENTS
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
N
l
m
9 - 11
22.5 - 27.5
22.5 - 27.5
9.5 - 12.5
15 - 28
28 - 47
Application
Air Cleaner Housing Cover Nut
Intake Manifold Bolt (M8 x 20)
Intake Manifold Bolt (M8)
Exhaust Mainfold Stud Bolt
Exhaust Pipe Nut (Engine)
Exhaust Pipe Bolt
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1G2-1
Fastener Tightening Specifications . . . . . . . . 1G2-1
Maintenance and Repair . . . . . . . . . . . . . . 1G2-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1G2-2
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 1G2-2
Air Intake Shield . . . . . . . . . . . . . . . . . . . . . . 1G2-4
Intake Air Duct . . . . . . . . . . . . . . . . . . . . . . . 1G2-5
Intake Manifold . . . . . . . . . . . . . . . . . . . . . . . 1G2-7
Exhaust Manifold . . . . . . . . . . . . . . . . . . . . . 1G2-9
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст