Daewoo Matiz (2003 year). Manual — part 3
1A – 10 GENERAL ENGINE INFORMATION
GENERAL DIAGNOSIS (Cont’d)
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Condition
ÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑ
Probable cause
ÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑ
Correction
Low Oil Pressure
Malfunction of
Lubrication
D
Lowered function of the oil
pump.
D
Replace the pump.
System
D
Abrasion or damage of the
oil pump relief valve.
D
Replace the valve.
Engine Noise
Valve Noise
D
Inadequate valve clearance.
D
Adjust the valve clearance.
D
Abrasion of valve stem or
guide.
D
Replace the valve stem or
the guide.
D
Weak valve spring.
D
Replace the spring.
Piston, Ring,
Cylinder Noise
D
Abrasion of the piston, the
ring or the cylinder.
D
Boring the cylinder or
replace the piston, the ring
or the cylinder.
Connecting Rod
Noise
D
Abrasion of the connecting
rod bearing.
D
Replace the bearing.
D
Loosened the connecting rod
nut.
D
Tighten to the specified
torque.
Crankshaft
Noise
D
Abrasion of the crankshaft
bearing.
D
Replace the bearing.
D
Abrasion of the crankshaft
journal.
D
Grind or replace the
crankshaft journal.
D
Loosened bearing cap bolt.
D
Tighten to the specified
torque.
D
Excessive clearance of the
crankshaft thrust bearing.
D
Adjust or replace.
D
Low oil pressure.
D
Refer to “Low Oil Pressure”
in this section.
GENERAL ENGINE INFORMATION 1A – 11
CHECKING ENGINE FLUID LEVEL
Check the engine fluid level or condition. If needed, refill
or replace the oil.
Check the engine oil level within engine normal operat-
ing temperature as follows ;
1. After stopping the engine, wait for a few minutes to
accumulate oil into the oil pan.
2. After pulling out the oil level gauge (a), check the oil
level.
3. Clean the oil level gauge and insert the gauge into
guide.
4. After pulling out the oil level gauge again, recheck the
oil level and insert the gauge into guide again.
Important: Oil level should be between “MIN” mark and
“MAX” mark.
5. If oil level is below the “MIN” mark, refill engine oil as
much as the demanded quantify.
Important: If checking oil level under the engine cold
condition, oil is not accumulated into oil pan quickly and
correct level checking can not be performed. Therefore,
wait until temperature reaches the normal operating
condition and check the engine oil level.
D102A301
CHANGING ENGINE OIL OR OIL
FILTER
Tools Required
09915–47341 Oil Filter Wrench.
When checking engine oil level or condition, if needed,
change engine oil (including the filter) as follows ;
1. After stopping the engine, wait for a few minutes to
accumulate oil into the oil pan.
2. Remove the oil filter cap (b).
3. Remove the oil drain plug (c) and draw oil off.
D102A302
4. After drawing oil completely, tighten the oil drain plug
to 30–40 N
S
m (22–30 lb-ft).
5. Replace the oil filter using the oil filter wrench
09915–47341 (d).
D
Remove the air cleaner/resonator/snorkel as-
sembly.
D
After removing the bolts, remove the heat
shield.
D
Loosen the power steering pump cap screw and
pull the power steering hose into the front.
D
Remove the oil filter.
Important: Whenever changing engine oil, replace the
oil filter. When replacing new oil filter, apply engine oil on
oil filter sealing.
D102A303
1A – 12 GENERAL ENGINE INFORMATION
CHECKING ENGINE TIMING BELT
After checking the timing belt for looseness, crack, wear
or tension, replace the belt if necessary.
CHECKING ACCESSORY BELT
After checking the alternator belt (e), air conditioning/
power steering belt (f), air conditioning belt (g), power
steering belt (h), for looseness, crack, wear or tension,
replace the belt if necessary.
D102A304
CHECKING SPARK PLUG
After checking the spark plug for bad clearance, exces-
sive carbon deposit, worn electrode or damaged insula-
tor, replace the new one if necessary.
Remove and check the spark plug as follows ;
1. Pull the high tension cable cap portion (i), and discon-
nect the high tension cable from the spark plug.
If pulling the high tension cable (j), circuit could be
disconnected. Therefore, the cap portion should be
used.
D102A305
2. Remove the spark plugs from cylinder head using a
wrench.
3. Measure the spark plug clearance (k) with the filler
gauge. If measured value is not within the specified
value, adjust the grounding electrode.
When installing new spark plug, check the clearance
for equality and install it.
D102A306
GENERAL ENGINE INFORMATION 1A – 13
CHECKING AIR CLEANER ELEMENT
If the air cleaner element becomes dirty, engine efficien-
cy could be deteriorated.
Be sure to check the element often.
Especially, if a vehicle frequently runs on a dusty road,
check and replace the element often.
CHECKING FUEL FILTER
If fuel filter is used over the specified period, engine effi-
ciency is deteriorated by dust or foreign material.
Therefore, replace a new one within the specified peri-
od.
CHECKING FUEL SYSTEM
Check the fuel system as follows ;
D
Check the fuel line or line connection portion for dam-
age or leakage.
D
Check the fuel hose surface for damage.
D
Check the fuel cap for looseness.
CHECKING HOSE SYSTEM
Check the engine vacuum hose, PCV hose or canister
hose as follows ;
D
Check the hose surface for damage by heat or ma-
chine.
D
Check the hose for hardening, crack, tear, or coming
off.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст