Hyundai Elantra Hybrid (2023 year). Manual in english — page 4
03
ś NEVER lean on the door or center console or sit on
one side of the front passenger seat.
2/0%
ś Do not sit on the passenger seat wearing heavily
padded clothes such as ski wear and hip protector.
ODH035900K
ś Do not use car seat accessories such as thick blankets
and cushions which cover up the car seat surface.
ODH035901K
ś Do not place electronic devices such as laptops, DVD
player, or conductive materials such as water bottles
on the passenger seat.
ś Do not use electronic devices such as laptops and
satellite radios which use inverter chargers.
OHI038161
ś If large amount of liquid has been spilled on the
passenger seat, the air bag warning light may
illuminate or malfunction.
Therefore, make sure the seat has been completely
dried before driving the vehicle.
OHI038162
ś
Do not place sharp objects on the front passenger seat. These may damage the
occupant detection system, if they puncture the seat cushion.
ś
Do not place any items under the front passenger seat.
ś
When changing or replacing the seat or seat cover, use original items only.
The OCS has been developed based on using original HYUNDAI car seats only.
Altering or changing the authentic parts may result in system malfunction and
increase risk of injury when in collision. Any of the above could interfere with the
proper operation of the OCS sensor thereby increasing the risk of an injury in an
accident.
3-49
Seats & Safety System
WARNING
NEVER allow an adult passenger to ride
in the front passenger seat when the
“PASSENGER AIR BAG OFF” indicator
is illuminated. During a collision, the
air bag will not inflate if the indicator
is illuminated. Have your passenger
reposition themselves in the seat. If the
“PASSENGER AIR BAG OFF” indicator
remains illuminated after the passenger
repositions themselves properly
OHI038118
and the vehicle is restarted, have
Proper seated position for OCS
the passenger move to the rear seat
If the “PASSENGER AIR BAG OFF”
because the air bag will not inflate.
indicator is on when an adult is seated
in the front passenger seat, place the
NOTICE
Engine Start/Stop button in the OFF
position and ask the passenger to sit
The “PASSENGER AIR BAG OFF”
properly (sitting upright with the seat
indicator generally illuminates for
back in an upright position, centered
approximately 4 seconds after the
on the seat cushion with their seat belt
Engine Start/Stop button is in the ON
on, legs comfortably extended and their
position or after the engine is started.
feet on the floor). Restart the engine and
However, if the ignition switch or
have the person remain in that position.
Engine Start/Stop button is turned to
This will allow the system to detect the
the ON position within 3 minutes after
person and to enable the passenger air
ignition OFF, the indicator does not
bag. If the “PASSENGER AIR BAG OFF”
illuminate. If the front passenger seat
indicator is still on, ask the passenger to
is occupied, the OCS will then classify
move to the rear seat.
the front passenger after several more
seconds.
3-50
03
Do Not Install a Child Restraint in the
Why Didn’t My Air Bag Go Off in
Front Passenger’s Seat
a Collision?
Air bags are not designed to inflate in
every collision. There are certain types
of accidents in which the air bag would
not be expected to provide additional
protection. These include rear impacts,
second or third collisions in multiple
impact accidents, as well as low speed
impacts. Damage to the vehicle indicates
a collision energy absorption, and is not
an indicator of whether or not an air bag
should have inflated.
OHI039193N
Even though your vehicle is equipped
WARNING
with the OCS, never install a child
restraint in the front passenger’s seat.
To reduce the risk of an air bag
An inflating air bag can forcefully strike a
deploying unexpectedly and causing
child or child restraint resulting in serious
serious injury or death:
or fatal injury.
ś Do not hit or allow any objects to
impact the locations where air bags
or sensors are installed.
WARNING
ś Do not perform maintenance on or
ś NEVER place a rear-facing or front-
around the air bag sensors. If the
facing child restraint in the front
location or angle of the sensors is
passenger’s seat of the vehicle.
altered, the air bags may deploy
ś An inflating frontal air bag could
when they should not or may not
forcefully strike a child resulting in
deploy when they should.
serious injury or death.
ś Do not install bumper guards or
ś Always properly restrain children in
replace the bumper with a non-
an appropriate child restraint in the
genuine HYUNDAI parts. This may
rear seat of the vehicle.
adversely affect the collision and air
bag deployment performance.
ś Place the ignition switch in the
LOCK/OFF or ACC position when the
vehicle is being towed to prevent
inadvertent air bag deployment.
ś Have all air bag repairs performed by
an authorized HYUNDAI dealer.
3-51
Seats & Safety System
Air bag collision sensors
OCN7H030005/OCN7030046/OCN7030047/OCN7030048/OCN7030062
1. SRS control module/Rollover sensor
2. Front impact sensors
3. Side impact sensors (acceleration)
4. Side impact sensors (pressure)
3-52
03
Air bag inflation conditions
Side and curtain air bags
Side and curtain air bags are designed
to inflate when an impact is detected by
side collision sensors depending on the
severity of impact resulting from a side
impact collision.
Although the driver’s and front
passenger’s air bags are designed to
inflate only in frontal collisions, they also
may inflate in other types of collisions
if the front impact sensors detect a
sufficient impact. Side and curtain air
OCN7H030006
bags are designed to inflate only in side
impact collisions or rollover situations,
Front air bags
but they may inflate in other collisions
Front air bags are designed to inflate
if the side impact sensors detect a
in a frontal collision depending on the
sufficient impact.
severity of impact of the front collision.
If the vehicle chassis is impacted by
bumps or objects on unimproved roads,
the air bags may deploy. Drive carefully
on unimproved roads or on surfaces not
designed for vehicle traffic to prevent
unintended air bag deployment.
Air bag non-inflation conditions
OCN7H030007
OCN7H030008
In certain low-speed collisions the air
bags may not deploy. The air bags are
designed not to deploy in such cases
because they may not provide benefits
OCN7H030003
beyond the protection of the seat belts.
3-53
Seats & Safety System
OCN7H030009
OCN7030053
Front air bags are not designed to inflate
In an angled collision, the force of impact
in rear collisions, because occupants
may direct the occupants in a direction
are moved backward by the force of the
where the air bags would not be able to
impact. In this case, inflated air bags
provide any additional benefit, and thus
would not provide any additional benefit.
the sensors may not deploy any air bags.
OCN7H030010
OCN7H030011
Front air bags may not inflate in side
Just before impact, drivers often brake
impact collisions, because occupants
heavily. Such heavy braking lowers the
move in the direction of the collision,
front portion of the vehicle causing it
and thus in side impacts, front air bag
to “ride” under a vehicle with a higher
deployment would not provide additional
ground clearance. Air bags may not
occupant protection.
inflate in this “underride” situation
because deceleration forces that are
However, side and curtain air bags may
detected by sensors may be significantly
inflate depending on the severity of
reduced by such “underride” collisions.
impact.
3-54
03
SRS Care
The SRS is virtually maintenance-free
and there are no parts you can safely
service by yourself. If the SRS air bag
warning light does not illuminate when
the ignition switch is in the ON position,
or continuously remains on, have your
vehicle immediately inspected by an
authorized HYUNDAI dealer.
Any work on the SRS system, such as
removing, installing, repairing, or any
OCN7030056
work on the steering wheel, the front
Front air bags may not inflate in rollover
passenger’s panel, front seats and roof
accidents because air bag deployment
rails must be performed by an authorized
may not provide protection to the
HYUNDAI dealer. Improper handling of
occupants.
the SRS system may result in serious
However, side and curtain air bags may
personal injury.
inflate when the vehicle is rolled over by
a side impact collision.
WARNING
To reduce the risk of serious injury or
death, take the following precautions:
ś
Do not attempt to modify or
disconnect the SRS components or
wiring, including the addition of any
kind of badges to the pad covers or
modifications to the body structure.
ś
Do not place objects over or near
the air bag modules on the steering
wheel, instrument panel, or the front
passenger’s panel above the glove box.
OCN7H030012
ś
Clean the air bag pad covers with
Air bags may not inflate if the vehicle
a soft cloth moistened with plain
collides with objects such as utility poles
water. Solvents or cleaners could
or trees, where the point of impact is
adversely affect the air bag covers
concentrated and the collision energy is
and proper deployment of the
absorbed by the vehicle structure.
system.
ś
Always have inflated air bags
replaced by an authorized HYUNDAI
dealer.
ś
If components of the air bag system
must be discarded, or if the vehicle
must be scrapped, certain safety
precautions must be observed.
Consult an authorized HYUNDAI
dealer for the necessary information.
Failure to follow these precautions
could increase the risk of personal
injury.
3-55
Seats & Safety System
Additional Safety Precautions
Air Bag Warning Labels
Passengers should not move out of
or change seats while the vehicle is
moving. A passenger who is not wearing
a seat belt during a crash or emergency
stop can be thrown against the inside of
the vehicle, against other occupants, or
be ejected from the vehicle.
Do not use any accessories on seat
belts. Devices claiming to improve
occupant comfort or reposition the seat
belt can reduce the protection provided
by the seat belt and increase the chance
OCN7030069N
of serious injury in a crash.
Air bag warning labels, required by the
Do not modify the front seats.
U.S. National Highway Traffic Safety
Modification of the front seats could
Administration (NHTSA), are attached
interfere with the operation of the
to alert the driver and passengers of
supplemental restraint system sensing
potential risks of the air bag system. Be
components or side air bags.
sure to read all of the information about
the air bags that are installed on your
Do not place items under the front
vehicle in this Owners Manual.
seats. Placing items under the front seats
could interfere with the operation of the
supplemental restraint system sensing
components and wiring harnesses.
Do not cause impact to the doors.
Impact to the doors when the Engine
Start/Stop button is in the ON position
may cause the air bags to inflate.
Modifications to accommodate
disabilities. If you require modification
to your vehicle to accommodate
a disability, contact the HYUNDAI
Customer Connect Center at 800-633-
5151.
Adding equipment to or modifying
your air bag equipped vehicle
If you modify your vehicle by changing
your vehicle’s frame, bumper system,
front end or side sheet metal or ride
height, this may affect the operation of
your vehicle’s air bag system.
3-56
4. Instrument Cluster
Instrument Cluster
4-4
Instrument Cluster Control
4-5
Adjusting instrument cluster illumination
4-5
Gauges and Meters
4-5
Speedometer
4-5
Power gauge
4-6
Hybrid battery SOC (State of Charge) gauge
4-6
Fuel gauge
4-7
Outside temperature gauge
4-8
Odometer
4-8
Range
4-9
Transmission Shift Indicator
4-9
Dual clutch transmission shift indicator
4-9
Warning and Indicator Lights
4-10
Ready indicator
4-10
EV mode indicator
4-10
4
Service warning light
4-10
Air Bag Warning Light
4-10
Seat Belt Warning Light
4-11
Parking Brake & Brake Fluid Warning Light
4-11
Regenerative brake warning light
4-11
Anti-lock Brake System (ABS) Warning Light
4-12
Electronic Brake Force Distribution (EBD) System Warning Light
4-12
Electronic Parking Brake (EPB) Warning Light
4-12
AUTO HOLD Indicator Light
4-13
Motor Driven Power Steering (MDPS) Warning Light
4-13
Malfunction Indicator Lamp (MIL)
4-13
Charging System Warning Light
4-14
Engine Oil Pressure Warning Light
4-14
Low Fuel Level Warning Light
4-14
Master Warning Light
4-15
Low Tire Pressure Warning Light
4-15
Electronic Stability Control (ESC) Indicator Light
4-15
Electronic Stability Control (ESC) OFF Indicator Light
4-16
AUTO STOP indicator light
4-16
Immobilizer Indicator Light
4-16
Immobilizer Indicator Light (with smart key)
4-17
Turn Signal Indicator Light
4-17
Exterior Light Warning Light
4-17
LED headlight warning light
4-18
High Beam Indicator Light
4-18
Light ON Indicator Light
4-18
High Beam Assist indicator light
4-18
Forward Collision-Avoidance Assist Warning Light
4-18
Lane Keep Assist Indicator Light
4-19
Cruise Indicator Light
4-19
SPORT Mode Indicator Light
4-19
SMART Mode Indicator Light
4-19
Icy Road Warning Light
4-19
LCD Display Messages
4-20
Shift to P or N to start engine (for smart key system)
4-20
Shift to P (for smart key system and dual clutch transmission)
4-20
Low key battery (for smart key system)
4-20
Press brake pedal to start engine (for smart key system and dual clutch
transmission)
4-20
Key not in vehicle (for smart key system)
4-20
Key not detected (for smart key system)
4-20
Press START button again (for smart key system)
4-20
4
12V battery discharging due to additional electrical devices
4-21
Press START button with key (for smart key system)
4-21
Check BRAKE SWITCH fuse (for smart key system and automatic
transmission/intelligent variable transmission)
4-21
Door, Hood, Trunk Open Indicator
4-21
Sunroof Open
4-21
Low Pressure
4-22
Lights Mode
4-22
Wiper
4-22
Heated Steering Wheel turned off
4-22
Low washer fluid
4-22
Low fuel
4-23
Engine Overheated
4-23
Check headlight
4-23
Check headlight (Low)
4-23
Check turn signal
4-23
Check brake light
4-23
Check daytime running light
4-24
Check high mounted stop lamp
4-24
Check headlight LED
4-24
Check Forward Collision-Avoidance Assist system
4-24
Check Lane Keeping Assist system
4-24
Check Blind-Spot Collision Warning system
4-24
Check Driver Attention Warning system
4-25
Check High Beam Assist system
4-25
Check Smart Cruise Control system
4-25
4. Instrument Cluster
Ready to start driving
4-25
Check regenerative brakes
4-25
Stop vehicle and check brakes
4-25
Check Hybrid system
4-26
Stop safely and check Hybrid system
4-26
Check Hybrid system. Do not start engine
4-26
Stop safely and check power supply
4-26
Check virtual engine sound system
4-26
Refill inverter coolant
4-26
Park with engine On to charge battery
4-26
Start engine to avoid battery discharge
4-26
LCD Display (Type A)
4-27
LCD Display Control
4-27
LCD Display Modes
4-28
Trip computer mode
4-29
Turn By Turn (TBT) mode
4-29
4
Driving Assist mode
4-29
Master warning mode
4-30
User Settings Mode
4-31
Trip Computer
4-38
Trip modes
4-38
Average fuel economy/Instant fuel economy
4-38
Accumulated Info display
4-39
Drive Info display
4-40
Digital speedometer
4-40
Auto Stop accumulated time
4-40
Smart shift
4-41
LCD Display (Type B)
4-42
LCD Display Control
4-42
View Modes
4-43
Utility Group
4-44
Utility Items
4-44
Driving Assist group
4-45
Navigation group
4-45
Driving info. group
4-45
Warning message group
4-46
User Settings Mode
4-46
Instrument Cluster
INSTRUMENT CLUSTER
Conventional cluster (Type A)
Full LCD cluster (Type B)
The actual cluster in the vehicle may differ from the illustration.
For more information, refer to the "Gauges and Meters" in this chapter.
OCN7H040005N/OCN7H040001N
1. Power gauge
4. Fuel gauge
2. Speedometer
5. Warning and indicator lights
3. Hybrid Battery SOC (State of Charge)
6. LCD display (including trip computer)
gauge
4-4
04
Instrument Cluster Control
Gauges and Meters
Adjusting instrument cluster
Speedometer
illumination
Type A
Type B
OCN7H040009N
OCN7040005N
OCN7040081N
The speedometer indicates the speed of
When the vehicle's parking lamps or
the vehicle and is calibrated in miles per
headlights are on, press the illumination
hour (MPH) and/or kilometers per hour
control button to adjust the brightness of
(km/h).
the instrument panel illumination.
When pressing the illumination control
button, the interior switch illumination
intensity is also adjustable.
ś The brightness of the instrument
panel illumination is displayed.
ś If the brightness reaches the
maximum or minimum level, a chime
will sound.
WARNING
Never adjust the instrument cluster
while driving. Doing so could lead to
driver distraction which may cause an
accident and lead to vehicle damage,
serious injury, or death.
4-5
Instrument Cluster
Power gauge
Hybrid battery SOC (State of Charge)
gauge
Type A
Type B
Type A
OCN7H040006
OCN7H040002
The power gauge indicates whether the
OCN7H040007
current driving condition is fuel efficient
Type B
or not.
ś CHARGE : Shows that the energy
made by the vehicle is being
converted to electrical energy.
(Regenerated energy)
ś ECO : Shows that the vehicle is being
driven in an Eco-friendly manner.
ś POWER : Shows that the vehicle is
exceeding the Eco-friendly range.
OCN7H040003
Information
This gauge indicates the remaining
Accordance to the power gauge area
hybrid battery power. If the SOC is near
the“EV” indicator comes on or off.
the “0 or L (Low)” level, the vehicle
automatically operates the engine to
-
“EV” indicator ON : Vehicle is driven
charge the battery.
using the electric motor or the gasoline
engine is stopped.
However, if the Service Indicator (
)
and Malfunction Indicator Lamp (MIL) (
-
“EV” indicator OFF : Vehicle is driven
using the gasoline engine.
) turn on when the SOC gauge is near
the “0 or L (Low)” level, we recommend
the vehicle be checked by an authorized
HYUNDAI dealer.
NOTICE
Never try to start the vehicle if the fuel
tank is empty. In this condition, the
engine cannot charge the high voltage
battery of the hybrid system. If you
try to start the vehicle when the fuel
is empty, the high voltage battery will
become discharged and be damaged.
4-6
04
Fuel gauge
WARNING
Type A
Running out of fuel can expose vehicle
occupants to danger.
You must stop and obtain additional
fuel as soon as possible after the
warning light comes on or when the
gauge indicator comes close to the "E
(Empty)" level.
NOTICE
Avoid driving with an extremely low
OCN7H040008
fuel level. Running out of fuel could
Type B
cause the engine to misfire and damage
the catalytic converter.
OCN7H040016N
This gauge indicates the approximate
amount of fuel remaining in the fuel tank.
Information
ś The fuel tank capacity is given in
chapter 2.
ś The fuel gauge is supplemented by
a low fuel warning light, which will
illuminate when the fuel tank is nearly
empty.
ś On inclines or curves, the fuel gauge
pointer may fluctuate or the low fuel
warning light may come on earlier than
usual due to the movement of fuel in
the tank.
4-7
Instrument Cluster
Outside temperature gauge
Odometer
Type A
Type A
Type B
OTMA048112
OTMA048183
OCN7H040004N
Type B
The odometer indicates the total
distance that the vehicle has been
driven and should be used to determine
when periodic maintenance should be
performed.
ODN8A049031
This gauge indicates the current outside
air temperature by 1°F (1°C).
- Temperature range: -40°F ~ 140°F
(40°C ~ 60°C)
Note that the temperature indicated
on the LCD display may not change
as quickly as the outside temperature
(there may be a slight delay before the
temperature changes.)
You can change the temperature unit
from °F to °C or °C to °F in the User
Settings mode in the cluster:
-
*R WR 8VHU 6HWWLQJV 0RGH Ɵ 2WKHU Ɵ
Temperature Unit.
For vehicles equipped with Automatic
Climate Control, you can also:
- Press and hold the AUTO and OFF
buttons on the climate control unit for
3 seconds
Both the temperature unit on the cluster
LCD display and climate control screen
will change.
4-8
04
Range
Transmission Shift Indicator
Type A
Type B
Dual clutch transmission shift
indicator
Type A
OCN7040084N
OCN7040016N
ś
The range is the estimated distance
the vehicle can be driven with the
OIG046112
remaining fuel.
Type B
ś
If the estimated distance is below
1 mi. (1 km), the trip computer will
display "----" as range.
Information
ś
If the vehicle is not on level ground or
the battery power has been interrupted,
the range function may not operate
correctly.
OCN7040013N
ś
The range may differ from the actual
This indicator displays which shift lever
driving distance as it is only an estimate
position is selected.
of the available driving range for the
vehicle and driving conditions.
ś
The trip computer may not register
additional fuel if less than 1.6 gallon (6
liters) of fuel are added to the vehicle.
ś
The range may vary significantly based
on driving conditions, driving habits,
and condition of the vehicle.
4-9
Instrument Cluster
Warning and Indicator Lights
Service warning light
Information
This warning light illuminates:
Make sure that all warning lights are OFF
ś When you set the ignition switch or
after starting the engine. If any light is still
the Engine Start/Stop button to the
ON, this indicates a situation that needs
ON position.
attention.
- The service warning light illuminates
for approximately 3 seconds and
Ready indicator
then turns off when all checks have
been performed.
ś When there is a problem with the
This indicator illuminates:
hybrid vehicle control system or
hardware.
When the vehicle is ready to be driven.
- ON : Normal driving is possible.
When the warning light illuminates
- OFF : Normal driving is not possible,
while driving, or does not go OFF after
or a problem has occurred.
starting the vehicle, we recommend that
- Blinking : Emergency driving.
you have the vehicle inspected by an
authorized HYUNDAI dealer.
When the ready indicator goes OFF
or blinks, there is a problem with the
Air Bag Warning Light
system. If this occurs, we recommend
that you have the vehicle inspected by an
authorized HYUNDAI dealer.
This warning light illuminates:
ś When you place the ignition switch to
EV mode indicator
the ON position.
- The air bag warning light illuminates
for about 6 seconds and then turns
This indicator illuminates:
off when all checks have been
When the vehicle is driven by the electric
performed
motor.
ś The air bag warning light will remain
illuminated if there is a malfunction
with the Safety Restraint System (SRS)
air bag operation.
In this case, have the vehicle
inspected by an authorized HYUNDAI
dealer.
4-10
04
Seat Belt Warning Light
Dual-diagonal braking system
Your vehicle is equipped with dual-
diagonal braking systems. This means
This warning light informs the driver that
you still have braking on two wheels even
the seat belt is not fastened.
if one of the dual systems should fail.
For more information, refer to “Seat
With only one of the dual systems
Belts” in chapter 3.
working, more than normal pedal travel
and greater pedal pressure is required to
Parking Brake & Brake Fluid
stop the vehicle.
Warning Light
If the brakes fail while you are driving,
shift to a lower gear for additional engine
braking and stop the vehicle as soon as it
This warning light illuminates:
is safe to do so.
ś When you place the ignition switch to
the ON position.
- The parking brake light illuminates
WARNING
for about 3 seconds and will then
Parking Brake & Brake Fluid Warning
turn off once the parking brake is
Light
released.
Driving the vehicle with a warning light
ś Whenever the parking brake is
ON is dangerous. If the Parking Brake &
applied.
Brake Fluid Warning Light illuminates
ś Whenever the brake fluid level in the
with the parking brake released, it
reservoir is low.
indicates that the brake fluid level is
low.
- If the warning light illuminates
with the parking brake released, it
In this case, have the vehicle inspected
indicates that the brake fluid level in
by an authorized HYUNDAI dealer.
the reservoir is low.
Regenerative brake warning
If the brake fluid level in the reservoir is
light
(yellow)
low:
1. Drive carefully to the nearest safe
This warning light illuminates:
location and stop your vehicle.
When the regenerative brake does not
2. With the engine stopped, check
operate and the brake does not perform
the brake fluid level immediately
well. This causes the Brake Warning
and add fluid as required (For more
light (red) and Regenerative Brake
information, refer to "Brake Fluid" in
Warning Light (yellow) to illuminate
chapter 9). After adding brake fluid,
simultaneously.
check all brake components for fluid
If this occurs, drive safely and we
leaks. If a brake fluid leak is found, or
recommend that you have the vehicle
if the warning light remains on, or if
inspected by an authorized HYUNDAI
the brakes do not operate properly, do
dealer.
not drive the vehicle. Have the vehicle
The operation of the brake pedal may
inspected by an authorized HYUNDAI
be more difficult than normal and the
dealer.
braking distance may increase.
4-11
Instrument Cluster
Anti-lock Brake System (ABS)
Information - Electronic Brake
Warning Light
Force Distribution (EBD)
This warning light illuminates:
System Warning Light
ś When you place the ignition switch to
When the ABS Warning Light is on
the ON position.
or both ABS and Parking Brake &
Brake Fluid Warning Lights are on, the
- The ABS warning light illuminates
speedometer, odometer, or tripmeter may
for about 3 seconds and then turns
not work. Also, the MDPS Warning Light
off.
may illuminate and the steering effort may
ś Whenever there is a malfunction with
increase or decrease.
the ABS.
In this case, have the vehicle inspected by
Note that the hydraulic braking
an authorized HYUNDAI dealer as soon
system will still be operational even if
as possible.
there is a malfunction with the ABS.
Electronic Parking Brake
Electronic Brake Force
(EPB) Warning Light
EPB
Distribution (EBD) System
(if equipped)
Warning Light
This warning light illuminates:
ś When you place the Engine Start/Stop
button to the ON position.
- The EPB warning light illuminates
These two warning lights illuminate at the
same time while driving:
for approximately 3 seconds and
then turns off.
When the ABS and regular brake system
ś Whenever there is a malfunction with
may not work normally.
the EPB.
In this case, have the vehicle inspected
If this occurs, have the vehicle
by an authorized HYUNDAI dealer.
inspected by an authorized HYUNDAI
dealer.
WARNING
Electronic Brake Force Distribution
Information
(EBD) System Warning Light
The Electronic Parking Brake (EPB)
When both ABS and Parking Brake &
Warning Light may illuminate when
Brake Fluid Warning Lights are on, the
the Electronic Stability control (ESC)
brake system will not work normally
Indicator Light comes on to indicates that
and you may experience an unexpected
the ESC is not working properly (This
and dangerous situation during sudden
does not indicate malfunction of the EPB).
braking.
In this case, avoid high speed driving
and abrupt braking.
Have the vehicle inspected by an
authorized HYUNDAI dealer as soon as
possible.
4-12
04
AUTO HOLD Indicator Light
Malfunction Indicator Lamp
(if equipped)
(MIL)
This indicator light illuminates:
This warning light illuminates:
ś
[White] When you activate the auto
ś When you place the ignition switch to
hold system by pressing the AUTO
the ON position.
HOLD button.
- The malfunction indicator light
ś
[Green] When you stop the vehicle
illuminates for about 3 seconds and
completely by depressing the brake
then goes off.
pedal with the auto hold system
ś Whenever there is a malfunction with
activated.
either the emission control system or
ś
[Yellow] When there is a malfunction
the engine or the vehicle powertrain.
with the auto hold system.
If this occurs, have the vehicle
In this case, have the vehicle
inspected by an authorized HYUNDAI
inspected by an authorized HYUNDAI
dealer.
dealer.
For more information, refer to “Auto
NOTICE
Hold” in chapter 6.
Driving with the Malfunction Indicator
Lamp (MIL) on may cause damage to
Motor Driven Power Steering
the emission control system which
(MDPS) Warning Light
could affect drivability and/or fuel
economy.
This warning light illuminates:
NOTICE
ś When you place the ignition switch to
the ON position.
If the Malfunction Indicator Lamp
(MIL) illuminates, potential catalytic
- The Motor Driven Power Steering
Warning light illuminates for about 3
converter damage is possible which
could result in loss of engine power.
seconds and then goes off.
ś Whenever there is a malfunction with
In this case, have the vehicle inspected
by an authorized HYUNDAI dealer as
the MDPS.
soon as possible.
If this occurs, have the vehicle
inspected by an authorized HYUNDAI
If the oil pressure lowers due to
dealer.
insufficient engine oil, etc., the engine
oil pressure warning light turns on
and an enhanced engine protection
system that limits the engine’s power
is activated. After that, engine warning
light turns on if driving repeatedly and
continuously.
4-13
Instrument Cluster
Charging System Warning
NOTICE
Light
ś If the engine is not turned OFF
immediately after the Engine
When this warning light illuminates while
Oil Pressure Warning Light is
the engine is running, the battery is not
illuminated, severe damage could
being charged. Immediately turn OFF
occur.
all electrical accessories. Try not to use
ś If the warning light stays on while the
electrically operated controls, such as
engine is running, it indicates that
the power windows. Keep the engine
there may be serious engine damage
running.
or malfunction. In this case:
Have the vehicle inspected by an
1. Stop the vehicle as soon as it is
authorized HYUNDAI dealer as soon as
safe to do so.
possible.
2. Turn off the engine and check the
oil level. If the oil level is low, fill
Engine Oil Pressure Warning
the engine oil to the proper level.
Light
3. Start the engine again. If the
warning light stays on after the
This warning light illuminates:
engine has started, turn the
engine off immediately. In this
When the engine oil pressure is low.
case, have the vehicle inspected
by an authorized HYUNDAI dealer.
If the engine oil pressure is low:
1. Drive carefully to the nearest safe
Low Fuel Level Warning Light
location and stop your vehicle.
2. Turn the engine off and check
the engine oil level (For more
information, refer to "Engine Oil" in
This warning light illuminates:
chapter 2). If the level is low, add oil
When the fuel tank is nearly empty. Add
as required.
fuel as soon as possible.
If the warning light remains on after
adding oil or if oil is not available, have
NOTICE
the vehicle inspected by an authorized
Driving with the Low Fuel Level warning
HYUNDAI dealer as soon as possible.
light on or with the fuel level below "E"
can cause the engine to misfire and
WARNING
damage the catalytic converter.
When oil pressure is restored to an
optimal level, the oil pressure warning
light and the protection system that
limits engine power will turn off. Even
if the oil pressure returns to normal,
check the engine once again in a safe
place.
4-14
04
Master Warning Light
This warning light remains ON after
blinking for approximately 60 seconds, or
repeatedly blinks ON and OFF in 3 second
intervals:
This indicator light illuminates:
When there is a malfunction with the
When there is a malfunction in operation
TPMS.
in any of the following functions
In this case, have the vehicle inspected
- Forward Collision-Avoidance Assist
by an authorized HYUNDAI dealer as
malfunction (if equipped)
soon as possible.
- Forward Collision-Avoidance Assist
For more information, refer to "Tire
radar blocked (if equipped)
Pressure Monitoring System (TPMS)" in
- Blind-Spot Collision Warning
chapter 8.
malfunction (if equipped)
- Blind-Spot Collision Warning radar
WARNING
blocked (if equipped)
- High Beam Assist malfunction
Safe Stopping
(if equipped)
ś The TPMS cannot alert you to severe
- Lamp malfunction (if equipped)
and sudden tire damage caused by
external factors.
- Smart Cruise Control malfunction
(if equipped)
ś If you notice any vehicle instability,
immediately take your foot off the
- Tire Pressure Monitoring System
accelerator pedal, apply the brakes
(TPMS) malfunction (if equipped)
gradually with light force, and slowly
To identify the details of the warning,
move to a safe position off the road.
look at the LCD display.
Electronic Stability Control
Low Tire Pressure Warning
(ESC) Indicator Light
Light (if equipped)
This indicator light illuminates:
This warning light illuminates:
ś When you place the ignition switch to
ś When you place the ignition in the ON
the ON position.
position.
- The Electronic Stability Control
- It illuminates for approximately 3
indicator light illuminates for about
seconds and then goes off.
3 seconds and then goes off.
ś When one or more of your tires are
ś Whenever there is a malfunction with
significantly underinflated. (The
the ESC system.
location of the underinflated tires is
If this occurs, have the vehicle
displayed on the LCD display.)
inspected by an authorized HYUNDAI
For more information, refer to "Tire
dealer.
Pressure Monitoring System (TPMS)" in
chapter 8.
This indicator light blinks:
While the ESC is operating.
For more information, refer to
“Electronic Stability Control (ESC)” in
chapter 6.
4-15
Instrument Cluster
Electronic Stability Control
Immobilizer Indicator Light
(ESC) OFF Indicator Light
This indicator light illuminates:
This indicator light illuminates:
ś When you place the ignition switch to
ś When the vehicle detects the
the ON position.
immobilizer in the key with the
ignition switch in the ON position.
- It illuminates for approximately 3
seconds and then goes off.
- At this time, you can start the engine.
ś When you deactivate the ESC system
- The indicator light goes off after
by pressing the ESC OFF button.
starting the engine.
For more information, refer to
“Electronic Stability Control (ESC)” in
This indicator light blinks:
chapter 6.
ś When there is a malfunction with the
immobilizer system.
AUTO STOP indicator light
If this occurs, have the vehicle inspected
(if equipped)
by an authorized HYUNDAI dealer.
This indicator light illuminates:
When the engine enters the Idle Stop
mode of ISG (Idle Stop and Go) system.
When the engine automatically starts,
the AUTO STOP indicator on the cluster
Illuminates to white.
For more details, refer to "ISG (Idle Stop
and Go) system" section in chapter 6.
Information
When the engine automatically starts
by the ISG system, some warning lights
(ABS, ESC, ESC OFF, MDPS or Parking
brake warning light) may turn on for a
few seconds. This happens because of
low battery voltage. It does not mean the
system has malfunctioned.
4-16
04
Immobilizer Indicator Light
Turn Signal Indicator Light
(with smart key)
(if equipped)
This indicator light illuminates for up to
This indicator light blinks:
30 seconds:
When you operate the turn signal
When the vehicle detects the smart key
indicator stalk.
in the vehicle with the Engine Start/Stop
button in the ACC or ON position.
If any of the following occur, there may be
- Once the smart key is detected, you
a malfunction with the turn signal system.
can start the engine.
- The turn signal indicator light
- The indicator light goes off after
illuminates but does not blink
starting the engine.
- The turn signal indicator light blinks
rapidly
This indicator light blinks for a few seconds:
- The turn signal indicator light does not
When the smart key is not in the vehicle.
illuminate at all
- If the smart key is not detected, you
If any of these conditions occur, have
cannot start the engine.
your vehicle inspected by an authorized
HYUNDAI dealer.
This indicator light illuminates for 2
For more details, refer to “High Beam
seconds and goes off:
Assist (HBA)” in chapter 5.
If the smart key is in the vehicle and the
Engine Start/Stop button is ON, but the
Exterior Light Warning Light
vehicle cannot detect the smart key.
(if equipped)
In this case, have the vehicle inspected
by an authorized HYUNDAI dealer.
This warning light illuminates:
ś When one of the exterior bulbs
This indicator light blinks:
(headlight, DRL, turn signal lamp, stop
When there is a malfunction with the
lamp, etc) is not operating properly.
immobilizer system.
One of the bulbs may need to be
In this case, have the vehicle inspected
replaced.
by an authorized HYUNDAI dealer.
Information
Make sure to replace the burned out bulb
with a new one of the same wattage rating.
4-17
Instrument Cluster
LED headlight warning light
High Beam Assist indicator
(if equipped)
light (if equipped)
This warning light illuminates:
This indicator light illuminates:
ś When you set the Engine Start/Stop
When the High Beam is on with the light
button to the ON position.
switch in the AUTO light position.
- The LED headlight warning light
ś White: When High Beam Assist is
illuminates for approximately 3
ready to operate.
seconds and then goes off.
ś Green: When High Beam Assist is
ś Whenever there is a malfunction with
operating.
the LED headlight.
If your vehicle detects oncoming or
If this occurs, have your vehicle
preceding vehicles, High Beam Assist
inspected by an authorized HYUNDAI
system will switch the high beam to low
dealer.
beam automatically.
For more information, refer to "High
NOTICE
Beam Assist (HBA)" in chapter 5.
Continuous driving with the LED
Headlight warning light on or blinking
Forward Collision-Avoidance
can reduce LED headlight life.
Assist Warning Light
(if equipped)
High Beam Indicator Light
This warning light illuminates:
ś When you set the ignition switch or
Engine Start/Stop button to the ON
This indicator light illuminates:
position.
ś When the headlights are on and in the
- It illuminates for approximately 3
high beam position.
seconds and then goes off.
ś When the turn signal lever is pulled
ś When there is a malfunction with
into the Flash-to-Pass position.
FCA. In this case, have your vehicle
inspected by an authorized dealer of
HYUNDAI.
Light ON Indicator Light
For more information, refer to "Forward
Collision-Avoidance Assist (FCA)" in
chapter 6.
This indicator light illuminates:
When the tail lights or headlights are on.
4-18
04
Lane Keep Assist Indicator
SMART Mode Indicator Light
Light (if equipped)
(if equipped)
60$57
This indicator light illuminates:
This indicator light illuminates:
ś
[Green] When you activate the lane
ś When you select ‘’SMART” mode as
departure warning system by pressing
drive mode.
the Lane Safety button and all of
For more details, refer to “Drive Mode
the system operating conditions are
Integrated Control System’’ in chapter
satisfied.
6.
ś
[White] When function operating
conditions are not satisfied or when
Icy Road Warning Light (if
the sensor does not detect the lane
equipped)
line.
ś
[Yellow] When there is a malfunction
with Lane Keeping Assist system.
This indicator light illuminates:
In this case, have your vehicle inspected
This warning light is to warn the driver
the road may be icy.
by an authorized HYUNDAI dealer.
For more information, refer to "Lane
When the temperature on the outside
Keeping Assist (LKA)" in chapter 6.
temperature gauge is approximately
below 40°F (4°C), the Icy Road Warning
Light and Outside Temperature Gauge
Cruise Indicator Light
blinks and then illuminates. Also, the
warning chime sounds 1 time.
The Icy Road Warning function can be
This indicator light illuminates:
activated or deactivated from the User
ś When the cruise control system is
Settings mode in the cluster LCD display.
enabled.
For more details, refer to “Cruise
Information
Control System” in chapter 6.
If the icy road warning light appears while
driving, you should drive more attentively
SPORT Mode Indicator Light
and safely, refraining from over-speeding,
(if equipped)
rapid acceleration, sudden braking or
sharp turning, etc.
This indicator light illuminates:
ś When you select “SPORT” mode as
drive mode.
For more details, refer to “Drive Mode
Integrated Control System” in chapter
6.
4-19
Instrument Cluster
LCD Display Messages
Key not in vehicle
(for smart key system)
Shift to P or N to start engine
(for smart key system)
This warning message is displayed if the
This warning message is displayed if you
smart key is not in the vehicle when you
press the Engine Start/Stop button.
try to start the engine with the shift lever
not in the P (Park) or N (Neutral) position.
When attempting to start the vehicle,
always have the smart key with you.
Information
Key not detected
You can start the engine with the shift
(for smart key system)
lever in the N (Neutral) position. But, for
This warning message is displayed if the
your safety, we recommend that you start
smart key is not detected when you press
the engine with the shift lever in the P
the Engine Start/Stop button.
(Park) position.
Press START button again
Shift to P (for smart key system and
(for smart key system)
dual clutch transmission)
This message is displayed if you were
This message is displayed if you try to
unable to start the vehicle when the
turn off the engine without the shift lever
Engine Start/Stop button was pressed.
in P (Park) position.
If this occurs, attempt to start the engine
If this occurs, the Engine Start/Stop
by pressing the Engine Start/Stop button
button turns to the ACC position (If you
again.
press the Engine Start/Stop button once
If the warning message appears each
more, it will turn to the ON position).
time you press the Engine Start/Stop
button, have your vehicle inspected by
Low key battery
an authorized HYUNDAI dealer.
(for smart key system)
This warning message is displayed if the
battery of the smart key is discharged
while changing the Engine Start/Stop
button to the OFF position.
Press brake pedal to start engine
(for smart key system and dual
clutch transmission)
This warning message is displayed if the
Engine Start/Stop button changes to
the ACC position twice by pressing the
button repeatedly without depressing
the brake pedal.
You can start the vehicle by depressing
the brake pedal and then pressing the
Engine Start/Stop button.
4-20
04
12V battery discharging due to
Door, Hood, Trunk Open Indicator
additional electrical devices
This message is displayed if the 12V
battery voltage is weak due to any
non-factory electrical accessories (ex.
dashboard camera) while parking. Be
careful that the battery is not discharged.
If the message appears after removing
the non-factory electrical accessories,
we recommend that you have the vehicle
inspected by an authorized HYUNDAI
dealer.
OCN7040017
Press START button with key
This warning is displayed if any door or
(for smart key system)
the hood or the liftgate is left open. The
This warning message is displayed if you
warning will indicate which door is open
press the Engine Start/Stop button while
in the display.
the warning message "Key not detected"
is displayed.
CAUTION
At this time, the immobilizer indicator
light blinks.
Before driving the vehicle, you should
confirm that the door/hood/liftgate
Check BRAKE SWITCH fuse (for
are fully closed. Also, check there is no
smart key system and automatic
door/hood/liftgate open warning light
or message displayed on the instrument
transmission/intelligent variable
cluster.
transmission)
This warning message is displayed if the
Sunroof Open (if equipped)
brake switch fuse is disconnected.
You need to replace the fuse with a new
one before starting the engine.
If that is not possible, you can start the
engine by pressing the Engine Start/
Stop button for 10 seconds in the ACC
position.
OCN7040018
This warning is displayed if you turn off
the engine when the sunroof is open.
Close the sunroof securely before leaving
your vehicle.
4-21
Instrument Cluster
Low Pressure
Wiper
OCN7040026L
OAD048579N
This warning message is displayed if the
This indicator displays which wiper speed
tire pressure is low. The corresponding
is selected using the wiper control.
tire on the vehicle will be illuminated.
Heated Steering Wheel turned off (if
For more information, refer to "Tire
Pressure Monitoring System (TPMS)" in
equipped)
chapter 8.
This message is displayed if you turn off
the heated steering wheel.
Lights Mode
For more details, refer to “Heated
Steering Wheel” in chapter 5.
Low washer fluid (if equipped)
This warning message is displayed if
the washer fluid level in the reservoir is
nearly empty.
Have the washer fluid reservoir refilled.
OIK047145L
This indicator displays which exterior
light is selected using the lighting
control.
4-22
04
Low fuel
Check headlight (Low) (if equipped)
This warning message is displayed if the
This warning message is displayed if
fuel tank is almost out of fuel.
the headlight (Low) are not operating
properly.
When this message is displayed, the low
fuel level warning light in the cluster will
In addition, if a specific lamp(turn signal
come on.
lamp etc.) is not operating properly, the
warning message according to a specific
It is recommended to look for the nearest
lamp (turn signal lamp etc.) is displayed.
fueling station and refuel as soon as
A corresponding bulb may need to be
possible.
replaced.
Make sure to replace the burned out
NOTICE
bulb with a new one of the same wattage
Do not drive the vehicle with low fuel.
rating
Hybrid battery damage may occur
when the fuel tank is completely empty.
Check turn signal (if equipped)
This warning message is displayed if the
Engine Overheated (if equipped)
turn signal lamps are not operat-
This warning message is displayed
ing properly. A lamp may need to be
when the engine coolant temperature
replaced.
is above 248°F (120°C). This means that
Make sure to replace the burned out
the engine is overheated and may be
damaged.
bulb with a new one of the same wattage
rating.
If your vehicle is overheated, refer to
“Overheating” in chapter 8.
Check brake light (if equipped)
This warning message is displayed if the
Check headlight (if equipped)
stop lamps are not operating properly. A
This warning message is displayed if the
lamp may need to be replaced.
headlights are not operating
Make sure to replace the burned out
properly.
bulb with a new one of the same wattage
In addition, if a specific lamp(turn signal
rating.
lamp etc.) is not operating properly, the
warning message according to a specific
lamp (turn signal lamp etc.) is displayed.
A corresponding bulb may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
4-23
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст