Hyundai Santa Fe (2023 year). Manual in english — page 11
Driving your vehicle
'8$/ &/87&+ 75
$160,66,21 ǣ,) (48,33('Ǥ
OTM060005
Dual clutch transmission operation
The dual clutch transmission has eight forward speeds and one reverse speed.
The individual speeds are selected automatically when the shift button is in the D
(Drive) position.
6-24
06
ś
The dual clutch transmission can be
ś
When rapidly accelerating from a
thought of as an automatically shifting
lower vehicle speed, the engine
manual transmission. It gives the
rpm may increase dramatically as a
driving feel of a manual transmission,
result of clutch slip as the dual clutch
yet provides the ease of a fully
transmission selects the correct gear.
automatic transmission.
This is a normal condition.
ś
When D (Drive) is selected, the
ś
When accelerating from a stop on
transmission will automatically
an incline, press the accelerator
shift through the gears similar to a
smoothly and gradually to avoid any
conventional automatic transmission.
shudder feeling or jerkiness.
Unlike a traditional automatic
ś
When traveling at a lower vehicle
transmission, the gear shifting can
speed, if you release the accelerator
sometimes be felt and heard as the
pedal quickly, you may feel engine
actuators engage the clutches and the
braking before the transmission
gears are selected.
changes gears. This engine braking
ś
The dual clutch transmission
feeling is similar to operating a
incorporates a wet-type dual clutch
manual transmission at low speed.
mechanism, which allows for better
ś
When driving downhill, you may
acceleration performance and
wish to move the gear shift button to
increased fuel efficiency while driving.
Manual Shift mode and downshift to
But it differs from a conventional
a lower gear in order to control your
automatic transmission because
speed without using the brake pedal
it does not incorporate a torque
excessively.
converter. Instead, the transition from
ś
When you turn the engine on and off,
one gear to the next is managed by
you may hear clicking sounds as the
clutch slip, especially at lower speeds.
system goes through a self-test. This
As a result, shifts are sometimes more
is a normal sound for the dual clutch
noticeable, and a light vibration can
transmission.
be felt as the transmission shaft speed
ś
During the first 1000 miles (1,500km),
is matched with the engine shaft
you may feel that the vehicle may not
speed. This is a normal condition of
be smooth when accelerating at low
the dual clutch transmission.
speed. During this break-in period, the
ś
The wet-type clutch transfers torque
shift quality and performance of your
more directly and provides a direct-
new vehicle is continuously optimized.
drive feeling which may feel different
from a conventional automatic
transmission. This may be more
noticeable when launching the vehicle
from a stop or when traveling at low,
stop-and-go vehicle speeds.
6-25
Driving your vehicle
DCT warning messages
WARNING
This warning message is displayed when
To reduce the risk of serious injury or
vehicle is driven slowly on a grade and
death:
the vehicle detects that the brake pedal
ś ALWAYS check the surrounding
is not applied.
areas near your vehicle for people,
especially children, before shifting a
vehicle into D (Drive) or R (Reverse).
ś Before leaving the driver’s seat,
always make sure the shift button
is in the P (Park) position, then set
the parking brake, and place the
ignition switch in the LOCK/OFF
position. Unexpected and sudden
vehicle movement can occur if these
precautions are not followed.
ś Do not use aggressive engine braking
(shifting from a higher gear to a
OOSH069010L
lower gear) on slippery roads. This
Steep grade! Press brake pedal
could cause the tires to slip and may
Driving up hills or on steep grades:
result in an accident.
ś To hold the vehicle on an incline use
the foot brake or the parking brake.
NOTICE
ś When in stop-and-go traffic on an
ś Always come to a complete stop
incline, allow a gap to form ahead
before shifting into D (Drive) or R
of you before moving the vehicle
(Reverse).
forward. Then hold the vehicle on the
ś Do not put the shift button in N
incline with the foot brake.
(Neutral) while driving.
ś If the vehicle is held or creeping
forward on an incline by applying
the accelerator pedal, the clutch and
WARNING
transmission may overheat which
Due to transmission failure, you may
can result in damage. At this time, a
not continue to drive and the position
warning message will appear on the
indicator and the position indicator (D,
LCD display.
P) on the instrument cluster will blink.
ś If the LCD warning is active, the foot
Contact an authorized HYUNDAI dealer
brake must be applied.
and have the system checked.
ś Ignoring the warnings can lead to
damage to the transmission.
6-26
06
Type A
Type B
OOSH069012L
OTMA060009
OOSH069013L
Transmission high temperature
ś
Under certain conditions, such as
repeated stop-and-go launches
on steep grades, sudden take off
or acceleration, or other harsh
driving conditions, the transmission
clutch temperatures will increase
excessively.
ś
When the clutch temperatures are too
high, the “Transmission temp. is high!
Stop safely” warning message will
OTMA060010
appear on the LCD display, a chime
will sound, and the transmission
Transmission overheated
shifting may not be smooth.
ś If the vehicle continues to be driven
ś
If this occurs, pull over to a safe
and the clutch temperatures reach
location, stop the vehicle with the
the maximum temperature limit, the
engine running, apply the brakes and
“Transmission Hot! Park with engine
shift the vehicle to P (Park), and allow
on” warning will be displayed. When
the transmission to cool.
this occurs the clutch is disabled
until the clutch cools to normal
ś
If you ignore this warning, the driving
temperatures.
condition may become worse.
You may experience abrupt shifts,
ś The warning will display a time to wait
frequent shifts, or jerkiness.
for the transmission to cool.
ś
When the message “Trans cooled.
ś If this occurs, pull over to a safe
Resume driving.” appears you can
location, stop the vehicle with the
continue to drive your vehicle.
engine running, apply the brakes and
shift the vehicle to P (Park), and allow
ś
When possible, drive the vehicle
the transmission to cool.
smoothly.
6-27
Driving your vehicle
ś When the message “Trans cooled.
R (Reverse)
Resume driving.” appears you can
Use this position to drive the vehicle
continue to drive your vehicle.
backward.
ś When possible, drive the vehicle
smoothly.
NOTICE
Always come to a complete stop before
If any of the warning messages in the
shifting into or out of R (Reverse); you
LCD display continue to blink, for your
may damage the transmission if you
safety, contact an authorized HYUNDAI
shift into R (Reverse) while the vehicle is
dealer and have the system checked.
in motion.
Transmission ranges
When the vehicle is stopped in
The indicator in the instrument cluster
R (Reverse) position, if you open
displays the shift button position when
the driver’s door with the seat belt
the ignition switch is in the ON position.
unfastened, the gear is shifted to P (Park)
position automatically.
P (Park)
However if the vehicle is moving in
Always come to a complete stop before
R(Reverse) position, if the driver's door
shifting into P (Park).
is opened with the seat belt unfastened,
To shift from P (Park), you must depress
the gear may not be shifted into P (Park)
firmly on the brake pedal and make sure
position automatically to protect the dual
your foot is off the accelerator pedal.
clutch transmission.
The shift button must be in P (Park)
before turning the engine off.
N (Neutral)
The wheels and transmission are not
engaged.
WARNING
Use N (Neutral) if you need to restart a
ś Shifting into P (Park) while the
stalled engine, or if it is necessary to stop
vehicle is in motion may cause you to
with the engine ON. Shift into P (Park)
lose control of the vehicle.
if you need to leave your vehicle for any
ś After the vehicle has stopped, always
reason.
make sure the shift button is in P
Always depress the brake pedal when
(Park), apply the parking brake, and
you are shifting from N (Neutral) to
turn the engine off.
another gear.
ś When parking on an incline, place
the shift button in P (Park) and apply
WARNING
the parking brake to prevent the
vehicle from rolling downhill.
Do not shift into gear unless your foot is
ś For safety, always engage the
firmly on the brake pedal. Shifting into
parking brake with the shift button
gear when the engine is running at high
in the P (Park) position except for the
speed can cause the vehicle to move
case of emergency parking.
very rapidly. You could lose control of
the vehicle and hit people or objects.
6-28
06
To stay in N (Neutral) when vehicle is
2. Push the N(Neutral) button by
OFF (button type)
depressing the brake pedal. If the
message (“Press and hold the OK
button on the steering wheel to stay in
Neutral ”) appears on the cluster LCD
display, press and hold the OK button
on the steering wheel for more than 1
second.
3. When the message ‘Vehicle will stay in
(N). Change gear to cancel’ (or ‘N will
stay engaged when the vehicle is Off’)
will appear on the cluster LCD display,
press the Engine Start/Stop button
OTM060006
while depressing the brake pedal.
However, if you open the driver's
door, the gear will automatically
shift to P (Park) and the Engine Start/
Stop button will change to the OFF
position.
NOTICE
With the gear in N (Neutral) the Engine
Start/Stop button will be in the ACC
position. Note that the doors cannot
OTM040050
be locked in the ACC position or the
battery may discharge if left in the ACC
If you want to stay in N (Neutral) after the
position for a long period.
engine is OFF (in the ACC state), do the
following.
1. Turn off Auto Hold and release
Electronic Parking Brake when the
engine is running.
6-29
Driving your vehicle
D (Drive)
Shift-lock system
This is the normal driving position. The
For your safety, the automatic
transmission will automatically shift
transmission has a shift-lock system
through a 8-gear sequence, providing
which prevents shifting the transmission
the best fuel economy and power.
from P (Park) or N (Neutral) to R
To start the vehicle forward, push the D
(Reverse) or D (Drive) unless the brake
(Drive) button by depressing the brake
pedal is depressed.
pedal with the engine ON. Then depress
To shift the transmission from P (Park)
the accelerator pedal smoothly. For extra
into R (Reverse):
power when passing another vehicle or
1. Depress and hold the brake pedal.
driving uphill, depress the accelerator
2. Start the engine or place the ignition
fully. The transmission will automatically
downshift to the next lower gear (or
switch in the ON position.
gears, as appropriate). When the vehicle
3. Depress the brake pedal and push the
is stopped in D (Drive) position, if you
R (Reverse) button.
open the driver’s door with the seat belt
unfastened, the gear is shifted to P (Park)
When the battery is discharged:
position automatically.
The shift buttons will not function when
However when the vehicle moves in D
the battery is discharged.
(Drive) position, if you open the driver’s
In emergencies, do the following to
door with the seat belt unfastened,
move the shift button to N (Neutral) on a
the gear may be not shifted to P (Park)
level ground.
position automatically for protecting the
1. Connect the battery cables from
dual clutch transmission.
another vehicle or from a another
The DRIVE MODE switch, located on the
battery to the jump-starting terminals
shift button console, allows the driver to
inside the engine compartment.
switch from NORMAL/ COMFORT mode
For more details, refer to “Jump
to SPORT or ECO mode. (if equipped)
Starting” in chapter 8.
For more details, refer to “Drive Mode
2. Release the parking brake with the
Integrated Control System” later in this
ignition switch in the ON position.
chapter.
3. Shift the gear to the N(Neutral)
position refer to the “Stay in Neutral
when vehicle is Off” in this chapter.
6-30
06
Parking
LCD display message (button
Always come to a complete stop and
type)
continue to depress the brake pedal.
Shifting conditions not met. Reduce
Press the P (Park) button, apply the
speed, then shift
parking brake, and place the ignition
The warning message appears on the
switch in the LOCK/OFF position. Take
LCD display, when engine RPM is too
the Key with you when exiting the
high, or when driving speed is too fast to
vehicle.
shift the gear.
We recommend you decrease the engine
WARNING
speed or slow down before shifting the
gear.
When you stay in the vehicle with
the engine running, be careful not to
Press brake pedal to change gear
depress the accelerator pedal for a long
period of time. The engine or exhaust
The warning message appears on the
system may overheat and start a fire.
LCD display, when the brake pedal is not
depressed while shifting the gear.
The exhaust gas and the exhaust system
are very hot. Keep away from the
We recommend you to depress the brake
exhaust system components.
pedal and then shift the gear.
Do not stop or park over flammable
Shift to P after stopping
materials, such as dry grass, paper or
leaves. They may ignite and cause a fire.
The warning message appears on the
LCD display, when the gear is shifted to P
(Park) while the vehicle is moving.
Stop the vehicle before shifting to P
(Park).
PARK engaged
The warning message appears on the
LCD display, when the gear is shifted to P
(Park) while the vehicle is moving.
Stop the vehicle before shifting to P
(Park).
6-31
Driving your vehicle
Press and hold the OK button on the
Shift button held down
steering wheel to stay in Neutral
The warning message appears on the
The warning message appears on
LCD display, when the shift button is
the LCD display, when pushing the
pressed continuously or the shift button
N(Neutral) button. If you want to stay
does not properly operate. Clean the
N(Neutral) after turning off the engine,
surroundings of gear shift button.
press and hold the “OK” button on the
If this message appears again, have
steering wheel more than 1 second.
the vehicle inspected by an authorized
HYUNDAI dealer.
Vehicle will stay in (N). Change gear
to cancel
Shifter system malfunction! Service
The warning message appears on the
immediately
LCD display, when pushing the “OK”
The warning message appears on the
button on the steering wheel after the
LCD display, when the transmission
message (“Press and hold OK button
or the shift button does not properly
to stay in Neutral when vehicle is Off”)
operate in the P (Park) position.
appears on the cluster LCD display. The
In this case, have the vehicle inspected
gear stays in N(Neutral) position after
immediately by an authorized HYUNDAI
turning off the engine.
dealer.
NEUTRAL engaged
Check shift controls
The message appears on the LCD
The warning message appears on the
display, when the N (Neutral) position is
LCD display, when there is a malfunction
engaged.
with transmission shift button.
Gear already selected
In this case, have the vehicle inspected
immediately by an authorized HYUNDAI
The message appears on the LCD
dealer.
display, when pushing the current shift
button again.
6-32
06
Paddle shifter (Manual shifter
To change back to automatic shift mode
from manual shift mode, do one of the
mode)
followings:
Pull the [+] paddle shifter for more than
one second Press the D button.
The manual shift mode also changes
back to automatic shift mode in one of
following situations
- When the accelerator pedal is gently
depressed for more than 6 seconds
while driving
- When the vehicle stops
OOSH069012L
The paddle shifter is available when the
Information
shift button is in the D (Drive) position or
If the [+] and [-] paddle shifters are pulled
the manual shift mode.
at the same time, gear shift may not occur.
With the shift button in the D
position
The paddle shifter will operate when the
vehicle speed is more than 6 mph.
Pull the [+] or [-] paddle shifter once
to shift up or down one gear and the
system changes from automatic mode to
manual shift mode.
In the manual shift mode, pull the [+]
or [-] paddle shifter once to shift up or
down one gear.
6-33
Driving your vehicle
Good driving practices
WARNING
ś
Never move the shift button from
To reduce the risk of SERIOUS INJURY
P (Park) or N (Neutral) to any other
or DEATH:
position with the accelerator pedal
ś
ALWAYS wear your seatbelt. In a
depressed.
collision, an unbelted occupant
ś
Never move the shift button into P
is significantly more likely to be
(Park) when the vehicle is in motion.
seriously injured or killed than a
Be sure the vehicle is completely
properly belted occupant.
stopped before you attempt to shift
ś
Avoid high speeds when cornering or
into R (Reverse) or D (Drive).
turning.
ś
Do not move the shift button to N
ś
Do not make quick steering wheel
(Neutral) when driving. Doing so
movements, such as sharp lane
may result in an accident because
changes or fast, sharp turns.
of a loss of engine braking and the
ś
The risk of rollover is greatly
transmission could be damaged.
increased if you lose control of your
ś
Do not drive with your foot resting
vehicle at highway speeds.
on the brake pedal. Even light, but
ś
Loss of control often occurs if two or
consistent pedal pressure can result
more wheels drop off the roadway
in the brakes overheating, brake wear
and the driver over steers to reenter
and possibly even brake failure.
the roadway.
ś
Always apply the parking brake when
ś
In the event your vehicle leaves
leaving the vehicle. Do not depend on
the roadway, do not steer sharply.
placing the transmission in P (Park) to
Instead, slow down before pulling
keep the vehicle from moving.
back into the travel lanes.
ś
Exercise extreme caution when
ś
HYUNDAI recommends you follow all
driving on a slippery surface. Be
posted speed limits.
especially careful when braking,
accelerating or shifting gears. On a
slippery surface, an abrupt change
in vehicle speed can cause the drive
wheels to lose traction and may cause
loss of vehicle control resulting in an
accident.
ś
Optimum vehicle performance and
economy is obtained by smoothly
depressing and releasing the
accelerator.
6-34
06
BRAKING SYSTEM
Power-assist brakes
WARNING
Your vehicle has power-assisted brakes
Take the following precautions:
that adjust automatically through normal
ś
Do not drive with your foot resting
usage.
on the brake pedal. This will create
If the engine is not running or is turned
abnormal high brake temperatures,
off while driving, the power assist for
excessive brake lining and pad wear,
the brakes will not work. You can still
and increased stopping distances.
stop your vehicle by applying greater
ś
When descending down a long or
force to the brake pedal than typical.
steep hill, use the paddle shifter
The stopping distance, however, will be
and manually downshift to a
longer than with power brakes.
lower gear in order to control your
When the engine is not running, the
speed without using the brake
reserve brake power is partially depleted
pedal excessively. Applying the
each time the brake pedal is applied.
brakes continuously will cause
Do not pump the brake pedal when the
the brakes to overheat and could
power assist has been interrupted.
result in a temporary loss of braking
performance.
Information
ś
Wet brakes may impair the vehicle's
ability to safely slow down; the
ś When the brake pedal is depressed
vehicle may also pull to one side
under certain driving conditions
when the brakes are applied.
or weather conditions, you may
Applying the brakes lightly will
temporarily hear a noise. This is
indicate whether they have been
normal and does not indicate a problem
affected in this way. Always test your
with your brakes.
brakes in this fashion after driving
ś While driving on a road with deicing
through deep water. To dry the
chemicals, brake noise or abnormal
brakes, lightly tap the brake pedal to
tire wear may occur due to deicing
heat up the brakes while maintaining
chemicals. In a safe traffic condition,
a safe forward speed until brake
additionally apply the brakes to remove
performance returns to normal.
deicing chemicals on the brake discs
Avoid driving at high speeds until the
and pads.
brakes function correctly.
6-35
Driving your vehicle
Disc brakes wear indicator
Emergency braking
When your brake pads are worn and new
If there is a problem with the brake
pedal while driving, emergency braking
pads are required, you will hear a high
pitched warning sound from your front
is possible by pulling up and holding
or rear brakes. You may hear this sound
the EPB switch. Braking is possible only
come and go or it may occur whenever
while you are holding the EPB switch.
you depress the brake pedal.
However, braking distance will be longer
than normal.
NOTICE
WARNING
To avoid costly brake repairs, do not
continue to drive with worn brake pads.
To reduce the risk of SERIOUS INJURY
or DEATH, do not operate the EPB
while the vehicle is moving except
Information
in an emergency situation. It could
Always replace brake pads as complete
damage the brake system and lead to
front or rear axle sets.
an accident.
Electronic Parking Brake (EPB)
Information
Applying the parking brake
During emergency braking, the Parking
Brake warning light will illuminate to
indicate that the system is operating.
NOTICE
If you continuously notice a noise or
burning smell when the EPB is used for
emergency braking, have the system
checked by an authorized HYUNDAI
dealer.
OTM060007
To apply EPB (Electronic Parking Brake):
1. Depress and hold the brake pedal.
2. Pull up the EPB switch.
Make sure the Parking Brake warning
light comes on.
EPB (Electronic Parking Brake) may be
automatically applied when:
ś Requested by other systems
ś The driver turns the vehicle off while
Auto Hold is operating.
6-36
06
Releasing the parking brake
Information
ś For your safety, you can engage EPB
even though the Engine Stop/Start
button is in the OFF position (only if
battery power is available), but you
cannot release it.
ś For your safety, depress the brake
pedal and release the parking brake
manually with the EPB switch when
you drive downhill or when backing up
the vehicle.
OTM060048L
NOTICE
To release EPB (Electronic Parking
Brake):
ś If the Parking Brake warning light is
1. Press the Engine Start/Stop button to
still on even though the EPB has been
the ON or START position.
released, have the system checked
by an authorized HYUNDAI dealer.
2. Press the EPB switch while depressing
the brake pedal.
ś Do not drive your vehicle with EPB
applied. It may cause excessive brake
Make sure the Parking Brake warning
pad and brake rotor wear.
light goes off.
ś Satisfy the following conditions
1. Ensure seat belts are fastened and the
doors, hood and liftgate are closed.
2. With the engine running, depress the
brake pedal and shift out of P (Park) to
R (Reverse), D (Drive) or Manual shift
mode.
3. Depress the accelerator pedal.
Make sure the Parking Brake warning
light goes off.
6-37
Driving your vehicle
Warning messages
ś NEVER allow anyone who is
unfamiliar with the vehicle to touch
the EPB switch. If EPB is released
unintentionally, serious injury may
occur.
ś Only release EPB when you are
seated inside the vehicle with your
foot firmly on the brake pedal.
NOTICE
ś
Do not apply the accelerator pedal
while the parking brake is engaged.
OTM058132L
If you depress the accelerator pedal
To release EPB, fasten seatbelt and close
with EPB engaged, a warning will
door, hood and liftgate
sound and a message will appear.
ś If you try to drive with EPB applied, a
Damage to the parking brake may
warning will sound and a message will
occur.
appear.
ś
Driving with the parking brake on
ś If the driver's seat belt is unfastened
can overheat the braking system and
and the engine hood or liftgate is
cause premature wear or damage
opened, a warning will sound and a
to brake parts. Make sure EPB is
message will appear.
released and the Parking Brake
warning light is off before driving.
ś If there is a problem with the vehicle,
a warning may sound and a message
may appear.
Information
If the situation occurs, depress the brake
ś
A clicking sound may be heard while
pedal and release EPB by pressing the
operating or releasing the EPB. These
EPB switch.
conditions are normal and indicate that
EPB is functioning properly.
WARNING
ś
When leaving your keys with a parking
attendant or assistant, make sure to
ś Whenever leaving the vehicle or
inform him/her how to operate EPB.
parking, always come to a complete
stop and continue to depress the
brake pedal.
Shift the gear into P (Park), pull
up the EPB switch, and press the
Engine Start/Stop button to the OFF
position. Take the Key with you when
leaving the vehicle.
Vehicles not fully engaged in P (Park)
with the parking brake set are at risk
for moving inadvertently and causing
injury to yourself or others.
6-38
06
EPB malfunction
Electronic Parking Brake (EPB) warning
light illuminates if the Engine Start/Stop
button is pressed to the ON position and
goes off in approximately 3 seconds if
the system is operating normally.
If the EPB warning light remains on,
comes on while driving, or does not
come on when the Engine Start/Stop
button is pressed to the ON position,
this indicates that the EPB may have
OIK060067L
malfunctioned.
AUTO HOLD turning Off!
If this occurs, have the system checked
Press brake pedal
by an authorized HYUNDAI dealer.
When the conversion from Auto Hold to
The EPB warning light may illuminate
EPB is not working properly a warning
when the ESC indicator comes on to
will sound and a message will appear.
indicate that ESC is not working properly,
but it does not indicate a malfunction of
EPB.
NOTICE
ś If the EPB warning light is still on,
have the system checked by an
authorized HYUNDAI dealer.
ś If the Parking Brake warning light
does not illuminate or blinks even
though the EPB switch was pulled
up, EPB may not be applied.
OIK060069L
ś If the Parking Brake warning light
Parking brake automatically engaged
blinks when the EPB warning light is
When EPB is applied while Auto Hold
on, press the switch, and then pull it
is activated, a warning will sound and a
up. Repeat this one more time. If the
message will appear.
EPB warning does not go off, have
the system checked by an authorized
HYUNDAI dealer.
6-39
Driving your vehicle
Parking brake warning light
Auto Hold (if equipped)
Check the Parking Brake
Auto Hold maintains the vehicle in a
warning light by pressing the
standstill even though the brake pedal is
Engine Stop/Start button to the
not depressed after the driver brings the
ON position.
vehicle to a complete stop by depressing
This light will be illuminated when the
the brake pedal.
parking brake is applied with the Engine
Stop/Start button in the START or ON
To apply:
position.
Before driving, be sure the parking
brake is released and the Parking Brake
warning light is OFF.
If the Parking Brake warning light
remains on after the parking brake is
released while the engine is running,
there may be a malfunction in the
brake system. Immediate attention is
necessary.
If at all possible, cease driving the vehicle
OTM060010
immediately. If that is not possible,
use extreme caution while operating
1.
With the driver’s door, engine hood
the vehicle and only continue to drive
and liftgate (vehicle equipped with
the vehicle until you can reach a safe
shift button) closed, then press the
location.
AUTO HOLD switch. The white AUTO
HOLD indicator will come on and the
When the EPB (Electronic Parking
system will be in the standby position.
Brake) does not release
If the EPB does not release normally,
contact an authorized HYUNDAI dealer
by loading the vehicle on a flatbed tow
truck and have the system checked.
6-40
06
To cancel:
OTM060057L
2. When you stop the vehicle completely
OTM060012
by depressing the brake pedal, Auto
1. Depress and hold the brake pedal.
Hold maintains the brake pressure
to hold the vehicle stationary. The
2. Press the AUTO HOLD switch.
indicator changes from white to
The AUTO HOLD indicator will turn off.
green.
3. The vehicle will remain stationary
WARNING
even if you release the brake pedal.
To prevent, unexpected and sudden
4. If EPB is applied, Auto Hold will be
vehicle movement, ALWAYS press your
released.
foot on the brake pedal to cancel the
Auto Hold before you:
To release:
- Drive downhill.
If you depress the accelerator pedal
with the gear in D (Drive), R (Reverse,
- Drive the vehicle in R (Reverse,
vehicle equipped with shift button) or
vehicle equipped with shift button).
Manual shift mode or R(vehicle equipped
- Park the vehicle.
with shift button), the Auto Hold will be
released automatically and the vehicle
will start to move. The AUTO HOLD
indicator changes from green to white.
WARNING
When Auto Hold is automatically
released by depressing the accelerator
pedal, always take a look around your
vehicle.
Slowly depress the accelerator pedal
for a smooth start.
6-41
Driving your vehicle
Information
WARNING
ś
The Auto Hold does not operate when:
ś Depress the accelerator pedal slowly
when you start the vehicle.
- The driver's door is opened
ś For your safety, cancel Auto Hold
- The engine hood is opened
when you drive downhill, back up the
- The liftgate is opened (vehicle
vehicle or park the vehicle.
equipped with shift button)
- The gear is in P (Park)
NOTICE
- The gear is in R (Reverse, vehicle
If there is a malfunction with the
equipped with shift lever)
driver's door or engine hood open
- EPB is applied
detection system, Auto Hold may not
ś
For your safety, the Auto Hold
work properly. Contact an authorized
automatically switches to EPB when:
HYUNDAI dealer.
- The driver's door is opened
Warning messages
- The engine hood is opened
Type A
Type B
- The vehicle is in a standstill for more
than 10 minutes
- The vehicle is standing on a steep
slope
- The vehicle moved several times
- The liftgate is opened
In these cases, the Parking Brake
warning light comes on, the AUTO
HOLD indicator changes from green
to white, and a warning sound and a
OJX1069028L
OJX1069066L
message will appear to inform you that
EPB has been automatically engaged.
Parking brake automatically engaged /
Before driving off again, depress the
Parking brake automatically applied
brake pedal, check the surrounding
When EPB is applied while Auto Hold
area near your vehicle and release the
is activated, a warning will sound and a
parking brake manually with the EPB
message will appear.
switch.
ś
While operating Auto Hold, you may
hear mechanical noise. However, it is
normal operating noise.
NOTICE
If the AUTO HOLD indicator changes
to yellow, Auto Hold is not working
properly. Contact an authorized
HYUNDAI dealer.
6-42
06
OOSH069024L
OTM060049L
Deactivating AUTO HOLD... Press brake
AUTO HOLD conditions not met.
pedal
Close door, hood and liftgate.
When the conversion from Auto Hold to
When you press the AUTO HOLD switch,
EPB is not working properly a warning
if the driver's door and engine hood are
will sound and a message will appear.
not closed, a warning will sound and a
message will appear on the cluster LCD
When this message is displayed, Auto
display.
Hold and EPB may not operate. For your
safety, depress the brake pedal.
Press the AUTO HOLD switch after
closing the driver's door and hood.
OJX1069035L
Press brake pedal to deactivate AUTO
HOLD
If you did not apply the brake pedal when
you release Auto Hold by pressing the
AUTO HOLD switch, a warning will sound
and a message will appear.
6-43
Driving your vehicle
Anti-lock Brake System (ABS)
Using ABS
To obtain the maximum benefit from
your ABS in an emergency situation,
WARNING
do not attempt to modulate your brake
Anti-Lock Braking System (ABS) or
pressure and do not try to pump your
Electronic Stability Control (ESC)
brakes. Depress your brake pedal as hard
system will not prevent accidents
as possible.
due to improper or dangerous driving
When you apply your brakes under
maneuvers. Even though vehicle
conditions which may lock the wheels,
control is improved during emergency
you may hear sounds from the brakes,
braking, always maintain a safe
or feel a corresponding sensation in the
distance between you and objects
brake pedal. This is normal and it means
ahead of you. Vehicle speeds should
your ABS is active.
always be reduced during extreme
ABS does not reduce the time or distance
road conditions. The braking distance
it takes to stop the vehicle.
for vehicles equipped with ABS or ESC
may be longer than for those without
Always maintain a safe distance from the
these systems in the following road
vehicle in front of you.
conditions.
ABS will not prevent a skid that results
Drive your vehicle at reduced speeds
from sudden changes in direction, such
during the following conditions:
as trying to take a corner too fast or
making a sudden lane change. Always
ś Rough, gravel or snow-covered
drive at a safe speed for the road and
roads.
weather conditions.
ś On roads where the road surface is
ABS cannot prevent a loss of stability.
pitted or has different surface height.
Always steer moderately when braking
ś Tire chains are installed on your
hard. Severe or sharp steering wheel
vehicle.
movement can still cause your vehicle to
The safety features of ABS or ESC
veer into oncoming traffic or off the road.
equipped vehicle should not be tested
On loose or uneven road surfaces,
by high speed driving or cornering. This
operation of the anti-lock brake system
could endanger the safety of yourself or
may result in a longer stopping distance
others.
than for vehicles equipped with a
conventional brake system.
ABS is an electronic braking system that
The ABS (
) warning light will stay
helps prevent a braking skid. ABS allows
on for several seconds after the Engine
the driver to steer and brake at the same
Start/Stop button is in the ON position.
time.
6-44
06
During that time, ABS will go through
Electronic Stability Control (ESC)
self-diagnosis and the light will go off if
everything is normal. If the light stays on,
you may have a problem with your ABS.
Contact an authorized HYUNDAI dealer
as soon as possible.
WARNING
If the ABS (
) warning light is on and
stays on, you may have a problem with
the ABS. Your power brakes will work
normally. To reduce the risk of serious
OTM060013
injury or death, contact your authorized
HYUNDAI dealer as soon as possible.
Electronic Stability Control helps to
stabilize the vehicle during cornering
maneuvers.
NOTICE
ESC checks where you are steering and
When you drive on a road having poor
where the vehicle is actually going. ESC
traction, such as an icy road, and apply
applies braking pressure to any one of
your brakes continuously, ABS will be
the vehicle's brakes and intervenes in the
active continuously and the ABS (
)
engine management system to assist the
warning light may illuminate. Pull your
driver with keeping the vehicle on the
vehicle over to a safe place and turn the
intended path. It is not a substitute for
vehicle off.
safe driving practices. Always adjust your
Restart the vehicle. If the ABS warning
speed and driving to the road conditions.
light is off, then your ABS system is
normal.
WARNING
Otherwise, you may have a problem
with your ABS system. Contact an
Never drive too fast for the road
authorized HYUNDAI dealer as soon as
conditions when cornering. ESC will not
possible.
prevent accidents.
Excessive speed in turns, abrupt
maneuvers, and hydroplaning on wet
Information
surfaces can result in severe accidents.
When you jump start your vehicle because
of a drained battery, the ABS (
)
warning light may turn on at the same
time. This happens because of the low
battery voltage. It does not mean your
ABS is malfunctioning. Have the battery
recharged before driving the vehicle.
6-45
Driving your vehicle
ESC operation
ESC OFF condition
ESC ON condition
To cancel ESC operation:
When the Engine Start/Stop button is
in the ON position, ESC and the ESC
OFF indicator lights illuminate for
ś State 1
approximately three seconds. After both
Press the ESC OFF button briefly. The
lights go off, ESC is enabled.
ESC OFF indicator light and/or message
'Traction Control disabled' will illuminate.
When operating
In this state, the traction control function
When ESC is in operation, the
of ESC (engine management) is disabled,
ESC indicator light blinks:
but the brake control function of ESC
(braking management) still operates.
ś
When you apply your brakes under
ś State 2
conditions which may lock the wheels,
you may hear sounds from the brakes,
Press and hold the ESC OFF button
or feel a corresponding sensation in
continuously for more than 3 seconds.
the brake pedal. This is normal and it
The ESC OFF indicator light and/or
means your ESC is active.
message 'Traction & Stability Control
disabled' illuminates and a warning
ś
When ESC activates, the engine may
chime sounds. In this state, both the
not respond to the accelerator as it
traction control function of ESC (engine
does under routine conditions.
management) and the brake control
ś
If Cruise Control was in use when ESC
function of ESC (braking management)
activates, Cruise Control automatically
are disabled.
disengages. Cruise Control can be
If the Engine Start/Stop button is pressed
reengaged when the road conditions
to the OFF position when ESC is off, ESC
allow. See “Cruise Control System”
remains off. Upon restarting the vehicle,
later in this chapter (if equipped).
ESC will automatically turn on again.
ś
When moving out of the mud or
driving on a slippery road, the engine
rpm (revolutions per minute) may
not increase even if you press the
accelerator pedal deeply. This is to
maintain the stability and traction of
the vehicle and does not indicate a
problem.
6-46
06
Indicator lights
NOTICE
Ŷ ESC indicator light (blinks)
Driving with wheels and tires with
different sizes may cause the ESC
system to malfunction. Before replacing
tires, make sure all four tires and wheels
are the same size. Never drive the
vehicle with different sized wheels and
Ŷ ESC OFF indicator light (comes on)
tires installed.
ESC OFF usage
When Driving
The ESC OFF mode should only be used
briefly to help free the vehicle if stuck in
When the Engine Start/Stop button is
snow or mud, by temporarily stopping
pressed to the ON position, the ESC
operation of ESC, to maintain wheel
indicator light illuminates, then goes off
torque.
if the ESC system is operating normally.
To turn ESC off while driving, press the
The ESC indicator light blinks whenever
ESC OFF button while driving on a flat
ESC is operating.
road surface.
If the ESC indicator light stays on, your
vehicle may have a malfunction with
NOTICE
the ESC system. When this warning light
To prevent damage to the transmission:
illuminates have the vehicle be checked
by an authorized HYUNDAI dealer as
ś Do not allow wheel(s) of one axle to
spin excessively while the ESC, ABS,
soon as possible.
and Parking Brake warning lights
The ESC OFF indicator light comes on
are displayed. The repairs would not
when ESC is turned off.
be covered by the vehicle warranty.
Reduce engine power and do not
spin the wheel(s) excessively while
WARNING
these lights are displayed.
When ESC is blinking, this indicates ESC
ś When operating the vehicle
is active:
on a dynamometer, make sure
Drive slowly and NEVER attempt to
ESC is turned off (ESC OFF light
accelerate. NEVER turn ESC off while
illuminated).
the ESC indicator light is blinking or you
may lose control of the vehicle resulting
in an accident.
Information
Turning ESC off does not affect ABS or
standard brake system operation.
6-47
Driving your vehicle
Vehicle Stability Management
VSM OFF condition
(VSM)
To cancel VSM operation, press the ESC
OFF button. ESC OFF (
) indicator light
Vehicle Stability Management is a
will illuminate.
function of the Electronic Stability
Control (ESC) system. It helps the vehicle
To turn on VSM, press the ESC OFF
stay stable when accelerating or braking
button again. The ESC OFF indicator light
suddenly on wet, slippery and rough
will go out.
roads where traction over the four tires
can suddenly become uneven.
WARNING
If the ESC (
) indicator light or EPS
WARNING
(
) warning light stays illuminated
Take the following precautions when
or blinks, your vehicle may have a
using Vehicle Stability Management:
malfunction with the VSM system.
When the warning light illuminates
ś ALWAYS check the speed and the
have the vehicle be checked by an
distance to the vehicle ahead. VSM
authorized HYUNDAI dealer as soon as
is not a substitute for safe driving
possible.
practices.
ś Never drive too fast for the road
conditions. VSM will not prevent
NOTICE
accidents. Excessive speed in bad
Driving with wheels and tires with
weather, on slippery and uneven
different sizes may cause the VSM
roads can result in severe accidents.
system to malfunction. Before replacing
tires, make sure all four tires and wheels
VSM operation
are the same size. Never drive the
When operating
vehicle with different sized tires and
wheels installed.
When you apply your brakes under
conditions which may activate ESC, you
may hear sounds from the brakes, or feel
a corresponding sensation in the brake
pedal. This is normal and it means your
VSM is active.
Information
VSM does not operate when:
ś Driving on a banked road such as
gradient or incline.
ś Driving in reverse.
ś The ESC OFF indicator light is on.
ś The EPS (Electric power steering)
warning light (
) is on or blinks.
6-48
06
Hill-Start Assist Control (HAC)
Downhill Brake Control (DBC)
Hill-Start Assist Control helps prevent
the vehicle from rolling backwards
when starting a vehicle from a stop on
a hill. The system operates the brakes
automatically for approximately 2
seconds and releases the brake after 5
seconds or when the accelerator pedal is
depressed.
WARNING
OTM060014
Always be ready to depress the
Downhill Brake Control assists the driver
accelerator pedal when starting off
an incline. Hill-Start Assist Control
to descend down a steep hill without
having to depress the brake pedal.
activates only for approximately 2
seconds.
The system automatically applies the
brakes to maintain vehicle speed below
a certain speed and allows the driver
Information
to concentrate on steering the vehicle
ś Hill-Start Assist Control does not
down hill.
operate when the gear is shifted to P
The system is turned off whenever the
(Park) or N (Neutral).
engine is turned off.
ś Hill-Start Assist Control activates even
Press the button to turn on the system
when the ESC (Electronic Stability
and press the button again to turn it off.
Control) is off. However, it does not
activate, when ESC does not operate
normally.
6-49
Driving your vehicle
System operation
Mode
Indicator
Description
Press the Downhill Brake Control button when vehicle
speed is under 37 mph (60 km/h). Downhill Brake
Standby
Control will turn on and enter the standby mode. The
system does not turn on if vehicle speed is over 37 mph
(60 km/h).
Green light on
In the standby mode, Downhill Brake Control will
activate under the following conditions:
ś The hill is steep enough.
ś The brake pedal or accelerator pedal is not depressed.
Activated
ś Vehicle speed is within 2~25 mph (4~40 km/h) range
(within 1.5~5 mph (2.5~8 km/h) when reversing).
Green light blink
Within the activation speed range 2~25 mph (4~40
km/h), the driver can control the vehicle speed by
depressing the brake pedal or accelerator pedal.
Downhill Brake Control will turn off under the following
conditions:
ś The Downhill Brake Control button is pressed again.
ś Vehicle speed is over 37 mph (60 km/h).
Green light off
Deactivated
Downhill Brake Control will be deactivated but maintain
the standby mode under the following conditions:
ś The hill is not steep enough.
ś Vehicle speed is between 25~37 mph (40~60 km/h).
Green light on
The yellow warning light illuminates when the system
may have malfunctioned or may not work properly
System
during activation. If this occurs, Downhill Brake Control
malfunction
is deactivated. Have the system be inspected by an
authorized HYUNDAI dealer as soon as possible.
Yellow light on
6-50
06
Information
ś
Downhill Brake Control may not
deactivate on steep inclines even though
the brake pedal or accelerator pedal is
depressed.
ś
Downhill Brake Control may not
always maintain vehicle speed at a
certain speed.
ś
Downhill Brake Control does not
operate when:
OJX1069039L
- The gear is in P (Park).
Downhill Brake Control disabled. Control
- ESC is activated.
vehicle speed (manually)
ś
Noise or vibration may occur from the
When Downhill Brake Control is not
brakes when Downhill Brake Control is
working properly this warning message
activated.
will appear on the cluster LCD display
and you will hear a warning sound. If
ś
The rear stop light comes on when
this occurs, control vehicle speed by
Downhill Brake Control is activated.
depressing the brake pedal.
WARNING
Always turn off Downhill Brake Control
on normal roads. The system might
activate inadvertently from the standby
mode when driving through speed
bumps or making sharp curves.
6-51
Driving your vehicle
Good braking practices
Wet brakes can be dangerous! The
brakes may get wet if the vehicle is
driven through standing water or if it
WARNING
is washed. Your vehicle will not stop as
quickly if the brakes are wet. Wet brakes
Whenever leaving the vehicle or
may cause the vehicle to pull to one side.
parking, always come to a complete
stop and continue to depress the brake
To dry the brakes, apply the brakes
pedal. Shift the gear to the P (Park)
lightly until the braking action returns to
position, then apply the parking brake,
normal. If the braking action does not
and press the Engine Start/Stop button
return to normal, stop as soon as it is safe
to the OFF position.
to do so and call an authorized HYUNDAI
dealer for assistance.
Vehicles parked with the parking brake
not applied or not fully engaged may
DO NOT drive with your foot resting on
roll inadvertently and may cause injury
the brake pedal. Even light, but constant
to the driver and others. ALWAYS apply
pedal pressure can result in the brakes
the parking brake before exiting the
overheating, brake wear, and possibly
vehicle.
even brake failure.
If a tire goes flat while you are driving,
apply the brakes gently and keep the
vehicle pointed straight ahead while you
slow down. When you are moving slowly
enough for it to be safe to do so, pull off
the road and stop in a safe location.
Keep your foot firmly on the brake pedal
when the vehicle is stopped to prevent
the vehicle from rolling forward.
6-52
06
)285 :+((/ '5,9( ǣ :'Ǥ ǣ,) (48,33('Ǥ
Four Wheel Drive (4WD) delivers engine
NOTICE
power to front and rear wheels for
ś
Do not drive in water if the level
maximum traction. 4WD is useful when
is higher than the bottom of the
extra traction is required, such as when
vehicle.
driving on, muddy, wet, or snow-covered
roads.
ś
Check your brake condition once
you are out of mud or water. Depress
the brake pedal several times as you
WARNING
move slowly until you feel normal
braking return.
To reduce the risk of SERIOUS INJURY
or DEATH:
ś
Shorten your scheduled
maintenance interval if you drive in
ś Do not drive in conditions that
off-road conditions such as sand,
exceed the vehicles intended
mud or water (see "Maintenance
design such as challenging off-road
Under Severe Usage Conditions"
conditions.
section in chapter 9).
ś Avoid high speeds when cornering or
ś
Always wash your vehicle thoroughly
turning.
after off road use, especially the
ś Do not make quick steering wheel
bottom of the vehicle.
movements, such as sharp lane
ś
Be sure to equip the vehicle with four
changes or fast, sharp turns.
tires of the same size and type.
ś The risk of a rollover is greatly
ś
Make sure that a full time 4WD
increased if you lose control of your
vehicle is towed by a flat bed tow
vehicle at highway speeds.
truck.
ś Loss of control often occurs if two or
more wheels drop off the roadway
and the driver over steers to reenter
the roadway.
ś In the event your vehicle leaves
the roadway, do not steer sharply.
Instead, slow down before pulling
back into the travel lanes.
6-53
Driving your vehicle
Four Wheel Drive (4WD) operation
Four Wheel Drive (4WD) mode selection
Transfer
Selection
Indicator
Description
mode
button
light
In the 4WD AUTO mode, under normal
operating conditions, onventional 2WD
vehicles. If the system determines
there is a need for four wheel drive, the
4WD AUTO
engine’s driving power is distributed to
(4WD LOCK is
all four wheels automatically.
deactivated)
Use this mode when driving on normal
(not
roads.
illuminated)
If you select the "Driving force
distribution" in the cluster, Driving force
distribution (4WD) state is displayed.
In the 4WD LOCK mode, the system is
deactivated when vehicle speed is over
37 mph (60 km/h) and the mode is shifted
to 4WD AUTO mode. If the vehicle speed
slows down to 37 mph (60 km/h), the
mode shifts back to the 4WD LOCK mode.
4WD LOCK
If 4WD Lock is activated, the driving force
distribution in the cluster is not displayed.
(illuminated)
Use this mode when driving up or down
steep inclines, driving off-road, driving on
sandy and muddy roads, etc., to maximize
traction
WARNING
If 4WD warning light (
) stays on the instrument cluster, your vehicle may have a
malfunction with the 4WD system. When the 4WD warning light (
) illuminates have
the vehicle be checked by an authorized HYUNDAI dealer as soon as possible.
6-54
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст