Hyundai Elantra GT (2018 year). Instruction — part 25
Instrument panel fuse panel
Fuse Name
Fuse Rating
Protected Component
MEMORY 2
7.5A
BCM
A/C Control Module, Instrument Cluster, Auto Light & Photo Sensor, Electro Chromic Mirror,
MEMORY 1
10A
ICM Relay Box (Outside Mirror Folding/Unfolding Relay)
AMP
30A
AMP
MODULE 6
7.5A
Smart Key Control Module, BCM
MDPS
7.5A
MDPS Unit
Hazard Switch, Center Door Lock Switch, Ignition Key Interlock Switch,
MODULE 1
7.5A
Driver/Passenger Smart Key Outside Handle, Data Link Connector
MODULE 7
7.5A
Front Seat Warmer Control Module, Front Air Ventilation Seat Control Module
A/BAG IND
7.5A
Instrument Cluster, Center Door Lock Switch
BRAKE
7
7.5A
Smart Key Control Module, Stop Lamp Switch
SWITCH
Without Smart Key : Ignition Key Switch
START
7.5A
With Smart Key : Smart Key Control Module
CLUSTER
7.5A
Instrument Cluster
DR LOCK
20A
Door Lock/Unlock Relay, ICM Relay Box (T/Turn Unlock Relay)
7-59
Maintenance
Instrument panel fuse panel
Fuse Name
Fuse Rating
Protected Component
AEB
10A
Autonomous Emergency Braking Module
S/HEATER
20A
Front Seat Warmer Control Module, Front Air Ventilation Seat Control Module
A/CON
7.5A
A/C Control Module, Cluster Ionizer, E/R Junction Block (Blower Relay)
SMART KEY 1
15A
Smart Key Control Module, Immobilizer Module
A/BAG
15A
SRS Control Module
IG1
25A
PCB Block (ABS3, ECU5, SENSOR4, TCU2)
Wireless Charger, Smart Key Control Module, BCM, A/V & Navigation Head Unit,
MODULE 2
10A
Power Outside Mirror Switch, E/R Junction Block (Power Outlet Relay), AMP
WASHER
15A
Multifunction Switch
WIPER
10A
ECM/PCM, BCM
(LO/HI)
WIPER (RR)
15A
Rear Wiper Relay, Rear Wiper Motor
HEATED
10A
Driver/Passenger Power Outside Mirror, A/C Control Module, ECM/PCM
MIRROR
POWER
20A
Rear Power Outlet #2
OUTLET
HEATED
15A
BCM
STEERING
7-60
Engine compartment fuse panel
OPD077037L
Inside the fuse/relay box cover, you
can find the fuse/relay label describ-
ing fuse/relay names and ratings.
i
Information
Not all fuse panel descriptions in this
7
manual may be applicable to your
vehicle; the information is accurate at
the time of printing. When you inspect
OPD077103N
the fuse panel in your vehicle, refer to
the fuse panel label.
7-61
Maintenance
Engine compartment fuse panel
Fuse Name
Fuse Rating
Protected Component
MAIN
150A
E/R Junction Block (Fuse - ABS1, ABS2, B/Alarm, Power Outlet1)
MDPS 1
80A
MDPS Unit, Battery
B+5
60A
PCB Block (Fuse - ECU4, ECU3, Horn, Wiper, Engine Control Relay)
B+2
60A
IGPM (Fuse - S/Heater, IPS0, IPS1, IPS2)
B+3
60A
IGPM (IPS3, IPS4, IPS5, IPS6, IPS7, IPS8)
B+4
60A
IGPM (Fuse - AMP, P/WDW LH, P/WDW RH, Tail Gate Open, Sunroof1, Sunroof2, P/Seat (DRV))
COOLING
60A
E/R Junction Block (Cooling Fan1 Relay)
FAN 1
REAR
40A
E/R Junction Block (Rear Heated Relay)
HEATED
BLOWER
40A
E/R Junction Block (Blower Relay)
IG1
40A
Ignition Switch, E/R Junction Block (ACC Relay, IG1 Relay)
IG2
40A
Ignition Switch, E/R Junction Block (IG2 Relay)
PTC
50A
PTC Heater1
HEATER 1
POWER
20A
Rear Power Outlet 1
OUTLET 3
7-62
Engine compartment fuse panel
Fuse Name
Fuse Rating
Protected Component
POWER
20A
Front Power Outlet
OUTLET 2
TCU1
15A
TCM
VACUUM
20A
Vacuum Pump
PUMP
FUEL PUMP
20A
E/R Junction Block (Fuel Pump Relay)
COOLING
40A
E/R Juntion Block (Cooling Fan2 Relay, Cooling Fan3 Relay)
FAN 2
B+1
40A
IGPM (Fuse - Door Lock, Smart Key1, Module1, Brake Switch, Reak Current Autocut Device)
DCT 1
40A
TCM
DCT 2
40A
TCM
B/ALARM
7
10A
ICM Relay Box (Burglar Alarm Horn Relay)
HORN
ABS 1
40A
Multipurpose Check Connector, ESC Control Module
ABS 2
30A
Multipurpose Check Connector, ESC Control Module
POWER
40A
E/R Junction Block (Power Outlet Relay)
OUTLET 1
B/UP LAMP
10A
Back-Up Lamp Switch
7-63
Maintenance
Engine compartment fuse panel
■ GAMMA 1.6L T-GDI
Fuse Name
Fuse Rating
Protected Component
Waste Gate Valve, Purge Control Solenoid Valve, Oil Control Valve #1/#2, RCV Control Solenoid Valve,
SENSOR2
10A
E/R Junction Block (Cooling Fan2 Relay, Cooling Fan1 Relay)
ECU2
10A
ECM
ECU1
20A
ECM
SENSOR1
15A
Oxygen Sensor (Up), Oxygen Sensor (Down)
IGN COIL
20A
Ignition Coil #1/#2/#3/#4
ECU3
15A
ECM
ECU5
10A
ECM
SENSOR4
15A
Vaccum Pump
ABS3
10A
ESC Control Module, Multipurpose Check Connector, Clutch Master Cylinder
TCU2
15A
E/R Junction Block (Fuse - B/Up Lamp), Transaxle Range Switch, TCM
SENSOR3
10A
E/R Junction Block (Fuel Pump Relay)
ECU4
15A
ECM
WIPER
25A
Wiper Relay
HORN
15A
Horn Relay
7-64
Engine compartment fuse panel
■ NU 2.0L GDI
Fuse Name
Fuse Rating
Protected Component
Purge Control Solenoid Valve, Oil Control Valve #1/#2, Variable Intake Solenoid Valve,
SENSOR2
10A
E/R Junction Block (Cooling Fan2 Relay, Cooling Fan3 Relay)
ECU2
10A
ECM/PCM
ECU1
20A
ECM/PCM
SENSOR1
15A
Oxygen Sensor (Up), Oxygen Sensor (Down)
IGN COIL
20A
Ignition Coil #1/#2/#3/#4, Condenser
ECU3
15A
ECM/PCM
ECU5
10A
ECM/PCM
ABS3
10A
ABS/ESC Control Module, Multipurpose Check Connector
7
ABS3
15A
E/R Junction Block (Fuse - B/Up Lamp), Transaxle Range Switch, TCM
SENSOR3
10A
E/R Junction Block (Fuel Pump Relay)
WIPER
25A
Wiper Relay
HORN
15A
Horn Relay
7-65
Maintenance
Engine compartment fuse panel
(Battery terminal cover)
OPD076066
Inside the fuse/relay box cover, you
can find the fuse/relay label describ-
ing fuse/relay names and ratings.
i
Information
Not all fuse panel descriptions in this
manual may be applicable to your
OPD076065
vehicle; the information is accurate at
the time of printing. When you inspect
NOTICE
the fuse panel in your vehicle, refer to
After checking the fuse panel in the engine compartment, securely
the fuse panel label.
install the cover. If it is not securely latched, electrical failure may occur
from water contact.
7-66
LIGHT BULBS
Consult an authorized HYUNDAI
Headlamp, Parking Lamp,
WARNING
dealer to replace most vehicle light
Daytime Running Light, Turn
bulbs. It is difficult to replace vehicle
Signal Lamp and Side Marker
•
Prior to replacing a lamp,
light bulbs because other parts of the
depress the foot brake, move
Type A
vehicle must be removed before you
the shift lever into P
(Park)
can get to the bulb. This is especially
true for removing the headlamp
apply the parking brake, place
the ignition switch to the
assembly to get to the bulb(s).
LOCK/OFF position, and take
Removing/installing the headlamp
the key with you when leaving
assembly can result in damage to
the vehicle to avoid sudden
the vehicle.
movement of the vehicle and
to prevent possible electric
i
Information
shock.
After heavy driving, rain or washing,
•
Be aware the bulbs may be
headlamp and trunk lenses could
hot and may burn your fin-
appear frosty. This condition is caused
gers.
OPD076042
by the temperature difference
between the lamp inside and the out-
(1) Headlamp (Low)
side temperature. This is similar to the
(2) Headlamp (High)
condensation on your windows inside
(3) Turn signal lamp
7
your vehicle during the rain and does-
(4) Parking lamp &
n’t indicate a problem with your vehi-
cle. If the water leaks into the lamp
Daytime running ight
bulb circuitry, have your vehicle
(5) Side marker
checked by an authorized HYUNDAI
dealer.
7-67
Maintenance
•
Always handle them carefully, and
■ High/Low beam
WARNING
avoid scratches and abrasions. If
Low
the bulbs are lit, avoid contact with
liquids.
•
Never touch the glass with bare
hands. Residual oil may cause the
bulb to overheat and burst when lit.
•
A bulb should be operated only
when installed in a headlamp.
High
•
If a bulb becomes damaged or
cracked, replace it immediately
OPDE076076
and carefully dispose of it.
OLMB073042L
1. Open the hood.
•
Handle halogen bulbs with
2. Disconnect the negative battery
care. Halogen bulbs contain
cable.
pressurized gas that will pro-
3. Remove the headlamp bulb cover
duce flying pieces of glass that
by turning it counterclockwise.
could cause injuries if broken.
4. Disconnect the headlamp bulb
•
Wear eye protection when
socket-connector.
changing a bulb. Allow the
bulb to cool down before han-
dling it.
7-68
5. Remove the bulb from the head-
5. Install a new bulb by inserting it
lamp assembly.
into the socket and rotating it until
it locks into place.
6. Install a new headlamp bulb and
snap the headlamp bulb retaining
6. Install the socket in the assembly
wire into position by aligning the
by aligning the tabs on the socket
wire with the groove on the bulb.
with the slots in the assembly.
7. Connect the headlamp bulb sock-
7. Push the socket into the assembly
et-connector.
and turn the socket clockwise.
8. Install the headlamp bulb cover by
turning it clockwise.
Parking lamp and daytime running
OPDE076077
light
i
Information
Your vehicle is equipped with LED
Turn signal
lamps. LED lamps do not have
The headlamp aiming should be
1. Open the hood.
replaceable bulbs. If the LED lamp
adjusted after an accident or after the
2. Disconnect the negative battery
does not operate, have the vehicle
headlamp assembly is reinstalled at an
cable.
checked by an authorized HYUNDAI
authorized HYUNDAI dealer.
3. Remove the socket from the
dealer.
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
7
the assembly.
4. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7-69
Maintenance
Type B
Side Repeater Lamp
Replacement
OAD075082N
Side marker
OPD076041
1. Open the hood.
OPD076044
(1) Headlamp (Low)
2. Disconnect the negative battery
(2) Headlamp (High)
If the light bulb does not operate,
cable.
have the vehicle checked by an
(3) Parking lamp & Turn signal lamp
3. Remove the socket from the
authorized HYUNDAI dealer.
& Daytime running light
assembly by turning the socket
(4) Side marker
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
Headlamp, parking lamp, turn sig-
4. Remove the bulb from the socket
nal lamp, daytime running light
by pulling out the bulb.
and side marker
5. Insert a new bulb.
Your vehicle is equipped with LED
lamps. LED lamps do not have
replaceable bulbs. If the LED lamp
does not operate, have the vehicle
checked by an authorized HYUNDAI
dealer.
7-70
Rear Combination Light Bulb
Replacement
Type A
OPD076047
OPD076048
Stop/Tail lamp and turn signal lamp
4. Remove the rear combination
lamp assembly from the body of
1. Open the liftgate.
the vehicle.
OPD076045
2. Open the lamp assembly retaining
screw covers.
(1) Stop/Tail lamp
3. Loosen the lamp assembly retain-
(2) Turn signal lamp
ing screws with a cross-tip screw-
(3) Tail lamp
driver.
(4) Back-up lamp
7
(5) Side marker
7-71
Maintenance
8. Install the socket into the assem-
bly by aligning the tabs on the
Stop/tail lamp
socket with the slots in the assem-
bly. Push the socket into the
assembly and turn the socket
clockwise.
9. Reinstall the lamp assembly to the
body of the vehicle.
Turn signal lamp
Side marker
OPD076049
Your vehicle is equipped with LED
OPDE076072
lamps. LED lamps do not have
5. Remove the socket from the
Tail lamp and backup lamp
replaceable bulbs. If the LED lamp
assembly by turning the socket
1. Open the liftgate.
does not operate, have the vehicle
counterclockwise until the tabs on
checked by an authorized HYUNDAI
2. Remove the service cover using a
the socket align with the slots on
dealer.
flat-blade screwdriver.
the assembly.
6. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
7-72
Type B
Tail lamp
Backup lamp
OPD076052
OPD076047
3. Remove the socket from the
Turn signal lamp
OPD076046
assembly by turning the socket
1. Open the liftgate.
(1) Stop/Tail lamp
counterclockwise until the tabs on
2. Open the lamp assembly retaining
the socket align with the slots on
(2) Turn signal lamp
screw covers.
the assembly.
(3) Backup lamp
3. Loosen the lamp assembly retain-
4. Pull the bulb out of the socket.
(4) Side marker
ing screws with a cross-tip screw-
5. Insert a new bulb into the socket.
driver.
6. Install the socket into the assem-
Stop/tail lamp and side marker
7
bly by aligning the tabs on the
Your vehicle is equipped with LED
socket with the slots on the
lamps. LED lamps do not have
assembly and turning the socket
replaceable bulbs. If the LED lamp
clockwise.
does not operate, have the vehicle
7. Reinstall the service cover.
checked by an authorized HYUNDAI
dealer.
7-73
Maintenance
8. Install the socket into the assembly
by aligning the tabs on the socket
Turn signal lamp
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Reinstall the lamp assembly to the
body of the vehicle.
OPD076048
OPD076064
4. Remove the rear combination
5. Remove the socket from the
lamp assembly from the body of
assembly by turning the socket
the vehicle.
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
6. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
7-74
High Mounted Stop Lamp
Replacement
Backup lamp
OPDE076072
OPD076053
Backup lamp
3. Remove the bulb by pulling it
straight out.
1. Open the liftgate.
OPD076054
4. Insert a new bulb by inserting it
2. Remove the service cover using a
1. Open the liftgate.
into the socket and rotating it until
flat-blade screwdriver.
it locks into place.
2. Gently remove the cover of the lift-
gate trim.
5. Install the socket into the assembly
by aligning the tabs on the socket
3. Remove the spoiler plug hole.
with the slots in the assembly.
4. Disconnect the connector and
7
Push the socket into the assembly
remove the washer hose and the
and turn the socket clockwise.
plug holes.
6. Reinstall the service cover.
5. Remove the mounting nuts.
6. Remove the rear spoiler assembly.
7-75
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст