Hyundai Elantra GT (2018 year). Instruction — part 10
Convenient features of your vehicle
The driving information will continue to
Digital speedometer
be counted while the engine is still run-
■ Type A
■ Type B
ning (for example, when the vehicle is
in traffic or stopped at a stop light).
i
Information
The vehicle must be driven for a mini-
mum of 0.19 miles (300 meters) since the
last ignition key cycle before the average
fuel economy will be recalculated.
OPDE046145R/OPDE046146R
This message shows the speed of
the vehicle.
3-80
LIGHTING
Exterior Lights
Daytime running light (DRL)
(if equipped)
Lighting control
The Daytime Running Lights (DRL)
To operate the lights, turn the knob at
can make it easier for others to see
the end of the control lever to one of
the front of your vehicle during the
the following positions:
day, especially after dawn and before
sunset.
3
The DRL system will turn the dedi-
cated lamp OFF when :
• The light switch is in the DRL OFF
OPD047036N
position.
AUTO light position (if equipped)
• The headlamps are ON.
The parking lamp and headlamp will
• The parking lamps are ON.
be turned ON or OFF automatically
• The vehicle is turned off.
depending on the amount of light
outside the vehicle.
OLF044084N
1. DRL (Daytime Running Lights)
Even with the AUTO light feature in
OFF position
operation, it is recommended to
2. AUTO light position
manually turn ON the lamps when
3. Parking lamp position
driving at night or in a fog, driving in
the rain, or when you enter dark
4. Headlamp position
areas, such as tunnels and parking
facilities.
3-81
Convenient features of your vehicle
NOTICE
• Do not cover or spill anything on
the sensor (1) located in front of
the instrument panel.
• Do not clean the sensor using a
window cleaner, the cleanser may
leave a light film which could
interfere with sensor operation.
• If your vehicle has window tint
or other types of metallic coat-
ing on the front windshield, the
OLF044086N
OLF044087N
AUTO light system may not work
Parking lamp position (
)
Headlamp position (
)
properly.
The parking lamp, license plate lamp
The headlamp, parking lamp, license
and instrument panel lamp are turned
plate lamp and instrument panel lamp
ON.
are turned ON.
i
Information
The ignition switch must be in the ON
position to turn on the headlamp.
3-82
High beam operation
Smart high beam
3
OLF044088N
To flash the high beam headlamp,
OLF044089N
OLF044090N
pull the lever towards you, then
To turn on the high beam headlamp,
The Smart High Beam is a system
release the lever. The high beams
push the lever away from you. The
that automatically adjusts the head-
will remain ON as long as you hold
lever will return to its original position.
lamp range (switches between high
the lever towards you.
beam and low beam) according to
The high beam indicator will light
when the headlamp high beams are
the brightness of other vehicles and
road conditions.
switched on.
To turn off the high beam headlamp,
pull the lever towards you. The low
Operating condition
beams will turn on.
1. Place the light switch in the AUTO
position.
WARNING
2. Turn on the high beam by pushing
the lever away from you.
Do not use high beam when there
The smart high beam (
) indica-
are other vehicles approaching
tor will illuminate.
you. Using high beam could
obstruct the other driver's vision.
3-83
Convenient features of your vehicle
3. The Smart High Beam will turn on
When the Smart High Beam is oper-
when vehicle speed is above
ating, the high beam switches to low
25 mph (40 km/h).
beam in the below conditions.
• If the light switch is pushed away
-
When the headlamp of an on-com-
when the Smart High Beam is
ing vehicle is detected.
operating, the Smart High Beam
-
When the tail lamp of a vehicle in
will turn off and the high beam will
front is detected.
be on continuously.
-
When headlamp/tail lamp of bicy-
• If the light switch is pulled towards
cle/motorcycle is detected.
you when the high beam is off, the
-
When the surrounding is bright
high beam will turn on without the
enough high beams are not needed.
ODM046655L
Smart High Beam canceled.
-
When streetlights or other lights
When you let go of the light switch,
Warning light and message
the lever will move to the middle
are detected.
When the Smart High Beam is not
and the high beam will turn off.
-
When the light switch is not in the
working properly, the warning mes-
• If the light switch is pulled towards
AUTO position.
sage will come on for a few second.
you when the high beam is on by
-
When the Smart High Beam is off.
After the message disappears, the
the Smart High Beam, the low
-
When vehicle speed is below 15 mph
master warning light (
) will illumi-
beam will be on and the Smart
(24 km/h).
nate. Take your vehicle to an author-
High Beam will turn off.
ized HYUNDAI dealer and have the
• If the light switch is placed to the
system checked.
headlamp position, the Smart
High Beam will turn off and the
WARNING
low beam will be on continuously.
The system may not operate nor-
mally in the below conditions.
• When the light from the on-
coming or in front vehicle is
not detected because of lamp
damage, hidden from sight, etc.
3-84
(Continued)
(Continued)
(Continued)
WARNING
•
When the lamp of the on-com-
•
When there is a traffic light,
ing or front vehicle is covered
reflecting sign, flashing sign or
•
Do not place any accessories,
with dust, snow or water.
mirror.
stickers or tint on the wind-
shield.
•
When the light from the on-
•
When the road conditions are
coming or front vehicle is not
bad such as being wet or cov-
•
Have the windshield glass
detected because of exhaust
ered with snow.
replaced from an authorized
3
fume, smoke, fog, snow, etc.
dealer.
•
When the front vehicle's head-
•
When the front window is cov-
lamps are off but the fog lamps
•
Be careful that water doesn't
ered with foreign matters such
on.
get into the Smart High Beam
as ice, dust, fog, or is damaged.
unit.
•
When a vehicle suddenly
•
When there is a similar shape
appears from a curve.
•
Do not remove or impact relat-
lamp with the front vehicle’s
ed parts of the Smart High
•
When the vehicle is tilted from
lamps.
Beam system.
a flat tire or being towed.
•
When it is hard to see because
•
Do not place objects on the
•
When the LKAS (Lane Keeping
of fog, heavy rain or snow.
dashboard that reflects light
Assist System) warning light
such as mirrors, white paper,
•
When the headlamp is not
illuminates.
etc. The system may malfunc-
repaired or replaced at an
tion if sunlight is reflected.
authorized dealer.
i
Information
•
At times, the Smart High
•
When headlamp aiming is not
Beam system may not work
properly adjusted.
When you replace or reinstall the wind-
properly, always check the
•
When driving on a narrow
shield glass/LKAS camera (if equipped),
road conditions for your safe-
curved road or rough road.
take your vehicle to an authorized
ty. When the system does not
•
When driving downhill or uphill.
HYUNDAI dealer and have the system
operate normally, manually
checked.
•
When only part of the vehicle in
change between the high
front is visible on a crossroad
beam and low beam.
or curved road.
(Continued)
3-85
Convenient features of your vehicle
Turn signals and lane change
Onetouch turn signal function
Battery saver function
signals
To activate the One Touch Turn
The purpose of this feature is to pre-
Signal function, push the turn signal
vent the battery from being dis-
lever up or down to position (B) and
charged. The system automatically
then release it.
turns off the parking lamp when the
driver turns the vehicle off and opens
The lane change signals will blink 3,
5 or 7 times.
the driver-side door.
With this feature, the parking lamps
You can activate or deactivate the
will turn off automatically if the driver
One Touch Turn Signal function or
parks on the side of road at night.
choose the number of blinks (3, 5, or
7) from the User Settings mode
If necessary, to keep the lamps on
(Light) on the LCD display.
when the vehicle is turned off, perform
the following:
OLF044091N
For more information, refer to the
1) Open the driver-side door.
"LCD Display" section in this
To signal a turn, push down on the
2) Turn the parking lamps OFF and
chapter.
lever for a left turn or up for a right
ON again using the light switch on
turn in position (A).
the steering column.
If an indicator stays on and does not
flash or if it flashes abnormally, one of
the turn signal bulbs may be burned
out and will require replacement.
3-86
Headlamp delay function
NOTICE
Interior Lights
(if equipped)
If the driver gets out of the vehicle
If the key is removed from the ignition
WARNING
through other doors (except dri-
switch or placed in the ACC position
ver's door), the battery saver func-
or the LOCK/OFF position with the
Do not use the interior lights
tion does not operate and the
headlamps ON, the headlamps
when driving in the dark.The inte-
headlamp delay function does not
(and/or parking lamps) remain on for
rior lights may obscure your view
turn off automatically. Therefore, It
about 5 minutes. However, if the dri-
and cause an accident.
3
causes the battery to be dis-
ver’s door is opened and closed, the
charged. In this case, make sure
headlights are turned off after
15
to turn off the lamp before getting
seconds. Also, with the engine off if
NOTICE
out of the vehicle.
the driver's door is opened and
Do not use the interior lights for
closed, the headlamps (and/or park-
extended periods when the vehi-
ing lamps) are turned off after 15
cle is turned off or the battery will
seconds.
discharge.
The headlamps
(and/or parking
lamps) can be turned off by pressing
the lock button on the remote key or
Interior lamp AUTO cut
smart key twice or turning the light
The interior lamps will automatically
switch to the OFF or AUTO position.
go off approximately 20 minutes after
the engine is turned off and the
You can activate or deactivate the
Headlamp Delay function from the
doors are closed. If a door is opened,
the lamp will go off 40 minutes after
User Settings Mode (Light) on the
LCD display.
the engine is turned off. If the doors
are locked by the remote key or
For more information, refer to the
smart key and the vehicle enters the
"LCD Display" section in this
armed stage of the theft alarm sys-
chapter.
tem, the lamps will go off five sec-
onds later.
3-87
Convenient features of your vehicle
Front lamps
Front room lamp (2)
Front Door Lamp (3) (
):
•
:
The front or rear room lamps come on
Press the button to turn ON the
when the front or rear doors are
room lamp for the front/rear seats.
opened if the engine is running or not.
When doors are unlocked by the
•
:
remote key or smart key, the front and
rear lamps come on for approximate-
Press the button to turn OFF the
ly 30 seconds as long as any door is
room lamp for the front/rear seats
not opened. The front and rear room
regardless of front or rear door open
lamps go out gradually after approxi-
position.
mately 30 seconds when the door is
closed. However, if the ignition switch
OPDE046041
is in the ON position or all doors are
(1) Front Map Lamp
locked, the front and rear lamps will
turn off. If a door is opened with the
(2) Front Room Lamp
ignition switch in the ACC position or
(3) Front Door Lamp
the OFF position, the front and rear
lamps stay on for about 20 minutes.
Front Map Lamp (1) :
Press either lenses to turn the map
lamp on or off. This light produces a
spot beam for convenient use as a
map lamp at night or as a personal
lamp for the driver and the front pas-
senger.
3-88
Rear lamp
Luggage compartment lamp
Vanity mirror lamp (if equipped)
■ Type A
3
OAD045407
■ Type B
OPD046042
OAD045410
The luggage compartment lamp
Push the switch to turn the light on or
comes on when the liftgate is
off.
opened.
•
: The lamp will turn on if this
button is pressed.
NOTICE
•
: The lamp will turn off if this
button is pressed.
The luggage compartment lamp
comes on as long as the liftgate is
NOTICE
open. To prevent unnecessary bat-
OPD046406
Always have the switch in the off
tery system drain, close the lift-
position when the vanity mirror
Rear Room Lamp (
):
gate securely after using the lug-
lamp is not in use. If the sunvisor
gage compartment.
Press this switch to turn the rear
is closed without the lamp off, it
room lamp on and off.
may discharge the battery or dam-
age the sunvisor.
3-89
Convenient features of your vehicle
Welcome System (if equipped)
Interior lamp
Welcome light (if equipped)
When the interior lamp switch is in
the DOOR position and all doors (and
Headlamp and parking lamp
trunk) are closed and locked, the
When the headlamp (with the lamp
room lamp will come on for 30 sec-
switch in the headlamp or AUTO
onds if any of the below is performed.
position) is on and all doors
(and
• When the door unlock button is
trunk) are locked and closed, the
pressed on the remote key or
parking lamp and headlamp will
smart key.
come on for 15 seconds when the
door unlock button is pressed on the
• When the button of the outside
door handle is pressed.
remote key or smart key.
At this time, if you press the door lock
At this time, if you press the door lock
or unlock button on the remote key or
or unlock button on the remote key or
smart key the room lamp will turn off
smart key the parking lamp and
headlamp will turn off immediately.
immediately.
You can activate or deactivate the
Welcome Light from the User Settings
Mode (Light) on the LCD display.
For more details, refer to "LCD
Display" in this chapter.
3-90
WIPERS AND WASHERS
■ Front windshield wiper/washer
A : Wiper speed control
OFF : Wiper is not in operation.
· MIST - Single wipe
INT : Wiper operates intermittently at
the same wiping intervals. To
· OFF - Off
vary the speed setting, move
· INT - Intermittent wipe
the speed control lever. The top
· LO - Low wiper speed
most setting will run the wipers
· HI - High wiper speed
most frequently (for more rain).
The bottom setting will run the
3
B : Intermittent control wipe time
wipers the least frequently (for
adjustment
less rain).
C : Wash with brief wipes
LO : The wiper runs at a lower speed.
OPD047454L
(pull lever towards you)
HI : The wiper runs at a higher speed.
■ Rear windshield wiper/washer
D : Rear wiper/washer control
i
Information
· HI - High wiper speed
If there is heavy accumulation of snow
· LO - Low wiper speed
or ice on the windshield, defrost the
· OFF - Off
windshield for about 10 minutes, or
E : Wash with brief wipes (rear)
until the snow and/or ice is removed
(push lever away from you)
before using the windshield wipers to
ensure proper operation.
Windshield Wipers
If you do not remove the snow and/or
ice before using the wiper and washer,
OTLA045318
Operates as follows when the igni-
it may damage the wiper and washer
tion switch is in the ON position.
system.
MIST : For a single wiping cycle,
push the lever upward and
release. The wipers will oper-
ate continuously if the lever is
held in this position.
3-91
Convenient features of your vehicle
Windshield Washers
Front windshield wiper service
WARNING
position
When the outside temperature
is below freezing, ALWAYS
warm the windshield using the
defroster to help prevent the
washer fluid from freezing on
the windshield and obscuring
your vision which could result
in an accident and serious
injury or death.
OTLE045164
NOTICE
OPD076027
In the OFF position, pull the lever
•
To prevent possible damage to
gently toward you to spray washer
This vehicle has a "hidden" wiper
the washer pump, do not operate
fluid on the windshield and to run the
design which means that the wipers
the washer when the fluid reser-
wipers
1-3 cycles. The spray and
cannot be lifted when they are in their
voir is empty.
wiper operation will continue until you
bottom resting position.
•
To prevent possible damage to
release the lever. If the washer does
1. Within 20 seconds of turning off the
the wipers or windshield, do not
not work, you may need to add wash-
engine, lift and hold the wiper lever
operate the wipers when the wind-
er fluid to the washer fluid reservoir.
up to the MIST position for about 2
shield is dry.
seconds until the wipers move to the
•
To prevent damage to the wiper
top wipe position.
arms and other components, do
2. At this time you can lift the wipers off
not attempt to move the wipers
the windshield.
manually.
3. Gently put the wipers back down
•
To prevent possible damage to
onto the windshield.
the wipers and washer system,
4. Turn the wipers to any ON position
use anti-freezing washer fluids in
to return the wipers to the bottom
the winter season or cold weather.
resting position.
3-92
Rear Window Wiper and Washer
Auto rear wiper (if equipped)
The rear wiper will operate while the
vehicle is in reverse with the front
wiper ON by selecting the function on
the LCD display.
Go to 'User Settings → Convenience
→ Auto Rear Wiper (reverse)'.
3
OTLE045166
Push the lever away from you to
OTLE045165
spray rear washer fluid and to run the
The rear window wiper and washer
rear wipers 1~3 cycles. The spray
switch is located at the end of the
and wiper operation will continue
wiper and washer switch lever. Turn
until you release the lever.
the switch to the desired position to
operate the rear wiper and washer.
HI - High wiper speed
LO - Low wiper speed
OFF - Off
3-93
Convenient features of your vehicle
DRIVER ASSIST SYSTEM
Rear View Camera
This is a supplemental system that
WARNING
helps provide a view of the area
behind the vehicle through the audio
•
Never rely solely on the Rear
display while the vehicle is in the R
(Reverse) position.
View Camera when backing-
up.
•
ALWAYS look around your
WARNING
vehicle to make sure there are
no objects or obstacles before
The Rear View Camera is not a
moving the vehicle in any
safety device. It only serves to
direction to prevent a collision.
assist the driver in identifying
OPDE046424
•
Always pay close attention
objects directly behind the mid-
when the vehicle is driven
dle of the vehicle. The camera
close to objects, particularly
does NOT cover the complete
pedestrians, and especially
area behind the vehicle.
children.
NOTICE
Always keep the camera lens
clean. The camera may not work
normally if the lens is covered
OPD047402L
with dirt, water or snow.
The Rear View Camera will activate
when the engine is running and the
shift lever is in the R (Reverse) posi-
tion.
3-94
MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)
■ Type A
3
1. Fan speed control knob
2. Temperature control knob
3. Mode selection buttons
4. Front windshield defroster button
5. Rear window defroster button
■ Type B
6. A/C (Air conditioning) button*
7. Air intake control button
* : if equipped
OPD047300N/OPD047301N
3-95
Convenient features of your vehicle
Heating and Air Conditioning
Mode selection
1. Start the engine.
2. Set the mode to the desired posi-
tion.
To improve the effectiveness of
heating and cooling, select:
- Heating:
- Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to the
outside (fresh) air or recirculated
air position.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn
the air conditioning system on.
(if equipped)
(if equipped)
OPDE046307/OPD046306
The mode selection button controls the direction of the air flow through the
ventilation system. Air can be directed to the floor, dashboard outlets, or
windshield. Five symbols are used to represent Face, Bi-Level, Floor, Floor-
Defrost and Defrost air position.
3-96
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст