Hyundai Atos: Body Repair Manual — part 33
138
SECTION D-D'
SECTION A-A'
SECTION C-C'
CORROSION PROTECTION - Antivibration pads
ANT-0010
EC ONLY
Center floor panel
SECTION B-B'
Side sill inner panel
10mm
84156-02000
Center floor panel
84156-02000
Rear floor panel
ANT-0011
ANT-0012
ANT-0013
ANT-0014
A
A'
!
!
!
!
B
B'
D'
Rear floor panel
25mm
84158-05000
ANTIVIBRATION PADS-LOCATION & SECTION
D
84152-02000
C'
C
!
!
!
!
84156-02000
84166-02000
84158-05060
84151-02000
84153-02000
84155-02000
84165-02000
84161-02000
84158-05060
84152-02000
139
CORROSION PROTECTION - Attachment of antivibration pads
ANT-0010
ATTACHMENT OF ANTIVIBRATION PADS
Antivibration pads are attached to the upper surface of the floor and at the interior side of the dash panel in order to absorb
vibrations and shut out exhaust gas heat. If these antivibration pads are peeled off in the course of replacement or repair
of a welded panel, cut and attach replacement material (in the shape shown in the figure).
1.
Heat the "antivibration pad" with a heater to soften it.
2.
Align the antivibration pad layer in the position where it is to be
installed, and then press it down with a roller or a block of wood
so that it adheres well.
NOTE
An infrared lamp can also be used to heat both the
antivibration pad layer and the body panels(be sure to
wear gloves).
COR-0006
COR-0007
84152-02000
84156-02000
84166-02000
84158-05060
84151-02000
84153-02000
84155-02000
84165-02000
84161-02000
84158-05060
140
SECTION D-D'
SECTION A-A'
SECTION C-C'
CORROSION PROTECTION - Under body coat
COR-0040
Dash panel
Center floor panel
Front side rear lower
member
SECTION B-B'
Side outer panel
Side sill inner panel
Center floor panel
Center floor side member
Center floor panel
Rear floor front
extension
Center floor side member
Because parts are to be mounted in these locations, mask the location, before applying
the under body coat.
Under body coating (Thickness: : 0.8mm,
: 1.0mm,
: 2.0mm)
COR-0041
COR-0042
COR-0043
COR-0044
!
!
!
!
B
B'
D'
!
Rear floor panel
Back panel
Fuel tank mounting
rear bracket
Rear floor center
cross member
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
UNDER BODY COAT
In order to provide corrosion, stone chipping and vibration resistance, under body coat is applied to the under sides of the
floor and wheel house.
Therefore, when such panel is replaced or repaired, apply under body coat to that part.
FLOOR
D
!
"
"
"
"
"
Front side rear
upper member
A
A'
C'
C
!
!
2- Ø 40 Masking
6- Ø 20 Masking
2- Ø 70 Masking
Ø 20 Masking
"
"
"
"
"
"
"
"
"
"
141
SECTION A-A'
CORROSION PROTECTION - Under body coat
SECTION B-B'
Front apron panel
Front inner lower
pillar
Front side inner
member
Because parts are to be mounted in these locations, mask the location before applying
the under body coat.
Under body coating (Thickness :
: 1.0mm,
: 2.0mm)
COR-0050/COR-0053/
COR0054
COR-0051
COR-0052
A
A'
!
B'
Wheel house inner
panel (LH)
Fuel filler house
Wheel house inner
panel (RH)
Quarter inner panel (RH)
"
"
"
"
"
SIDE BODY
Ø 20 Masking
(LH ONLY)
Ø 20 Masking
!
!
!
B
!
!
"A"
"B"
Ø 45 Masking
VIEW "A"
VIEW "B"
Ø 45 Masking
Quarter inner
panel (LH)
Front shock cover panel
80Masking
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст