Hyundai i30 (2018 year). Instruction — part 25
Driving your vehicle
Warning light and message
LDWS failure indicator
Limitations of the system
Check LDWS
The LDWS failure indica-
The LDWS may operate prematurely
tor (yellow) will illuminate
even if the vehicle does not depart
if the LDWS is not work-
from the intended lane, OR, the
ing properly. We recom-
LDWS may not warn you if the vehi-
mend you to have your vehicle
cle leaves the intended lane under
checked by an authorized HYUNDAI
the following circumstances:
dealer.
•
The lanes ahead are not visible
due to rain, snow, water on the
When there is a problem with the
road, damaged or stained road
system, do one of the following:
surface, or other factors.
• Turn the system on after turning
•
The brightness outside changes
the vehicle off and on again.
suddenly such as when entering or
OAE056164L
• Check if the ignition switch is in the
exiting a tunnel.
ON position.
•
The brightness outside is too low
If there is a problem with the system
• Check if the system is affected by the
such as when the headlamps are
a message will appear for a few sec-
weather. (e.g. fog, heavy rain, etc.)
not on at night or the vehicle is
onds.
going through a tunnel.
• Check if there is foreign matter on
If the problem continues the LDWS
the camera lens.
•
The surrounding of the inside rear
failure indicator will illuminate.
view mirror temperature is high
If the problem is not solved, we rec-
due to direct sunlight.
ommend you have the system
•
It is difficult to distinguish the lane
checked by an authorized HYUNDAI
marking from the road surface or
dealer.
the lane marking is faded or not
clearly marked.
•
Driving on a steep grade, over a
hill, or when driving on a curved
road.
5-116
•
When light coming from a street
•
The windshield glass is fogged up;
light or an oncoming vehicle is
a clear view of the road is obstruct-
reflected on a wet road surface
ed.
such as a puddle in the road.
•
There are markings on the road
•
The windshield or the LDWS cam-
surface that look like a lane line
era lens is blocked with dirt or
that is inadvertently being detected
debris.
by the camera.
•
The field of view in front is
•
There is a boundary structure in
obstructed by sun glare.
the roadway such as a concrete
•
The lanes are incomplete or the
barrier, guardrail and reflector post
that is inadvertently being detected
area is in a construction zone.
by the camera.
•
There are more than two lane lines
•
There is not enough distance
on the road in front of you.
between you and the vehicle in
5
•
The lane line is merged or divided.
front to be able to detect the lane
(e.g. tollgate)
line or the vehicle ahead is driving
•
The lane number increases or
on the lane line.
decreases or the lane marker are
•
The adverse road conditions cause
crossing complicatedly.
excessive vehicle vibrations while
•
The lane line in a tunnel is stained
driving.
with oil.
•
The lane markings are not clearly
visible from the road.
•
The lane width is too wide or too
narrow.
•
The shadow is on the lane marker
by a median strip, trees, etc.
5-117
Driving your vehicle
DRIVER ATTENTION ALERT SYSTEM (DAA) (IF EQUIPPED)
The Driver Attention Alert
(DAA),
•
The driver can select the Driver
Display of the driver's attention
system is to warn the driver with any
Attention Alert system mode.
level
hazardous driving situations upon
- Off
: The Driver Attention Alert
detecting the driver's fatigue level or
■ System off
system is deactivated.
inattentive driving practices.
- Normal
: The Driver Attention
Alert system alerts the driver of
System setting and activation
his/her fatigue level or inattentive
driving practices.
System setting
- Early : The Driver Attention Alert
•
The Driver Attention Alert system
system alerts the driver of his/her
is set to be in the OFF position,
fatigue level or inattentive driving
when your vehicle is first delivered
OPDE056125
practices faster than Normal
to you from the factory.
■ Attentive driving
mode.
•
To turn ON the Driver Attention
•
The set-up of the Driver Attention
Alert system, turn on the engine,
Alert system will be maintained, as
and then select 'User Settings
selected, when the engine is re-
Driving Assist Driver Attention
started.
Alert Normal/Early' on the LCD
display.
Prerequisite for activation
The Driver Attention Alert system is
OPDE056061
operable, when driving speed is
■ Inattentive driving
between 60 km/h (40 mph) and 200
km/h (125 mph).
OPDE056062
5-118
•
The driver can monitor their driving
Take a break
Resetting the system
conditions on the LCD display.
•
The last break time is set to 00:00
The DAA screen will appear when
and the driver's attention level is
you select the Assist Mode tab on
set to 5 (very attentive) when the
the LCD display if the system is
driver resets the Driver Attention
activated. (For more information,
Alert system.
refer to "LCD Modes" in chapter
•
The Driver Attention Alert system
3.)
resets the last break time to 00:00
•
The driver's attention level is dis-
and the driver's attention level to 5
played on the scale of 1 to 5. The
in the following situations.
lower the number is, the more inat-
- The engine is turned OFF.
tentive the driver is.
- The driver unfastens the seat belt
•
The number decreases when the
OPDE056063
and then opens the driver's door.
driver does not take a break for a
5
•
The "Consider taking a break"
- The engine has been idled con-
certain period of time.
message appears on the LCD dis-
tinuously over 10 minutes.
•
The number increases when the
play and a warning sounds in order
•
The Driver Attention Alert system
driver attentively drives for a cer-
to suggest the driver to take a
tain period of time.
operates again, when the driver
break, when the driver’s attention
restarts driving.
level is below 1.
•
The Driver Attention Alert system
does not suggest the driver to take
a break, when the total driving time
is shorter than 10 minutes.
5-119
Driving your vehicle
System standby
System malfunction
WARNING
•
The Driver Attention Alert
system is not a substitute for
safe driving practices, but a
convenience function only. It
is the responsibility of the
driver to always drive cau-
tiously to prevent unexpected
and sudden situations from
occurring. Pay attention to the
road conditions at all times.
OPDE056126
OPDE056065
•
The driver, who feels fatigued,
should take a break, even
The Driver Attention Alert system
When the "Check System" warning
though there is no break sug-
enters the ready status and displays
message appears, the system is not
gestion by the Driver Attention
the 'Standby' screen in the following
working properly. In this case, we rec-
Alert system.
situations.
ommend you to have the vehicle
inspected by an authorized HYUNDAI
- The camera sensor keeps failing to
dealer.
detect the lanes.
- Driving speed remains under
60
km/h (40 mph) or over 200 km/h
(125 mph).
5-120
NOTICE
CAUTION
(Continued)
The Driver Attention Alert system
•
The vehicle drives through a
utilizes the camera sensor on the
The Driver Attention Alert sys-
windy area.
front windshield for its operation.
tem may not properly operate
•
The vehicle is controlled by
To keep the camera sensor in the
with limited alerting in the fol-
the following driving assist
best condition, you should
lowing situations:
systems:
observe the followings:
•
The lane detection perform-
- Lane Keeping Assist System
•
NEVER install any accessories
ance is limited.
(For more
(LKAS)
or stickers on the front wind-
information, refer to "Lane
- Autonomous Emergency
shield, nor tint the front wind-
Keeping Assist System
Braking (AEB) System
shield.
(LKAS)" in this chapter.)
•
NEVER locate any reflective
•
The vehicle is violently driven
objects (i.e. white paper, mirror)
or is abruptly turned for
over the dashboard. Any light
obstacle avoidance (e.g. con-
5
reflection may cause a malfunc-
struction area, other vehicles,
tion of the Driver Attention Alert
fallen objects, bumpy road).
(DAA) system.
•
Forward drivability of the
•
Pay extreme caution to keep the
vehicle is severely under-
camera sensor out of water.
mined (possibly due to wide
variation in tire pressures,
•
NEVER arbitrarily disassemble
uneven tire wear-out, toe-
the camera assembly, nor apply
in/toe-out alignment).
any impact on the camera
assembly.
•
The vehicle drives on a curvy
road.
•
Playing the vehicle audio sys-
tem at high volume may offset
•
The vehicle drives on a
the Driver Attention Alert sys-
bumpy road.
tem warning sounds.
(Continued)
5-121
Driving your vehicle
SPEED LIMIT CONTROL SYSTEM (IF EQUIPPED)
Speed Limit Control operation
Speed limit control switch
To set speed limit
You can set the speed limit when you
do not want to drive over a specific
speed.
If you drive over the preset speed
limit, the warning system operates
(set speed limit will blink and chime
will sound) until the vehicle speed
returns within the speed limit.
i
Information
While speed limit control is in opera-
OPDE056114
OPDE056115
tion, the cruise control system cannot
be activated.
: Changes mode between cruise
1. Press the
button to turn the
control/smart cruise control
system on. The speed limit indica-
system and speed limit control
tor in the instrument cluster will
system.
illuminate.
System off
Cruise Control/Smart
Cruise Control
Speed Limit Control
RES+: Resumes or increases speed
limit control speed.
SET-: Sets or decreases speed limit
control speed.
O: Cancels set speed limit.
5-122
If you would like to drive over the pre-
To turn off the speed limit con-
set speed limit when you depress the
trol, do one of the following:
accelerator pedal less than approxi-
mately 50%, the vehicle speed will
maintain within speed limit.
However if you depress the acceler-
ator pedal more than approximately
70%, you can drive over the speed
limit. Then the set speed limit will
blink and chime will sound until you
return the vehicle speed within the
OPDE056116
speed limit.
2. Push the toggle switch down
(SET-).
OPDE056115
5
3. • Push the toggle switch up
(RES+) or down
(SET-), and
• Press the
button.
release it at the desired speed.
• If you press O
(cancel) button
• Push the toggle switch up
once, the set speed limit will can-
(RES+) or down (SET-) and hold
cel, but it will not turn the system
it. The speed will increase or
off. If you wish to resume the speed
decrease by 5 km/h.
limit, push the +RES or SET- tog-
The set speed limit will display on the
gle switch on your steering wheel
instrument cluster.
to your desired speed.
5-123
Driving your vehicle
CRUISE CONTROL (IF EQUIPPED)
Cruise Control operation
WARNING
(Continued)
•
Do not use the Cruise Control
Take the following precautions:
when it may be unsafe to keep
•
Always set the vehicle speed
the vehicle at a constant
under the speed limit in your
speed:
country.
- When driving in heavy traffic
•
If the Cruise Control is left on,
or when traffic conditions
(
indicator light in the
make it difficult to drive at a
instrument cluster is illumi-
constant speed
nated) the Cruise Control can
- When driving on rainy, icy, or
be activated unintentionally.
snow-covered roads
Keep the Cruise Control sys-
- When driving on hilly or
OPDE056066
tem off
(CRUISE indicator
windy roads
light OFF) when the Cruise
1. CRUISE indicator
- When driving in windy areas
Control is not in use, to avoid
2. SET indicator
inadvertently setting a speed.
•
Do not use cruise control
when towing a trailer.
•
Use the Cruise Control system
The Cruise Control system allows you
only when traveling on open
to drive at speeds above 30 km/h
highways in good weather.
NOTICE
(20 mph) without depressing the
(Continued)
accelerator pedal.
During cruise-speed driving of a
manual transmission vehicle, do
not shift into neutral without
depressing the clutch pedal, since
the engine will be overrevved. If
this happens, depress the clutch
pedal or press the cruise control
ON / OFF button.
5-124
i
Information
i
Information
•
During normal cruise control opera-
tion, when the SET switch is activat-
ed or reactivated after applying the
brakes, the cruise control will ener-
gize after approximately 3 seconds.
This delay is normal.
•
Before activating the cruise control
function, the system will check to
verify that the brake switch is oper-
ating normally. Depress the brake
OPDE056117
pedal at least once after turning ON
Cruise control switch
the ignition or starting the vehicle.
OPDE056115
O : Cancels cruise control operation.
5
First, switch the mode to Cruise
: Turns cruise control system on
Control by pressing the
button if
or off.
equipped with the Speed Limit
RES+: Resumes or increases cruise
Control System.
control speed.
The mode changes, as below, whenev-
SET-: Sets or decreases cruise con-
er the
button is pressed.
trol speed.
System off
Cruise Control
Speed Limit Control
5-125
Driving your vehicle
To set Cruise Control speed
To increase Cruise Control
speed
OPDE056119
3. Push the toggle switch down
OPDE056118
(SET-), and release it. The SET
OPDE056120
1. Press the
button on the steer-
indicator light will illuminate.
ing wheel to turn the system on.
4. Release the accelerator pedal.
• Push the toggle switch up (RES+)
The
indicator will illuminate.
and hold it, while monitoring the
2. Accelerate to the desired speed,
SET speed on the instrument clus-
i
Information
which must be more than 30 km/h
ter.
(20 mph).
On a steep slope, the vehicle may
Release the toggle switch when the
slightly slow down or speed up, while
desired speed is shown and the
driving uphill or downhill.
vehicle will accelerate to that speed.
i
Information - Manual trans-
mission
For manual transmission vehicles, you
should depress the brake pedal at
least once to set the cruise control
after starting the engine.
5-126
• Push the toggle switch up (RES+)
To decrease Cruise Control
To temporarily accelerate with
and release it immediately. The
speed
the Cruise Control ON
cruising speed will increase
2.0
Depress the accelerator pedal. When
km/h (1.2 mph) each time the tog-
you take your foot off the accelerator,
gle switch is operated in this man-
the vehicle will return to the previ-
ner.
ously set speed.
• Depress the accelerator pedal.
If you push the toggle switch down
When the vehicle attains the
(SET-) at the increased speed, the
desired speed, push the toggle
Cruise Control will maintain the
switch down (SET-).
increased speed.
OPDE056119
5
• Push the toggle switch down (SET-)
and hold it.Your vehicle will gradual-
ly slow down. Release the toggle
switch at the speed you want to
maintain.
• Push the toggle switch down (SET-)
and release it immediately. The
cruising speed will decrease
2.0
km/h (1.2 mph) each time the toggle
switch is operated in this manner.
• Lightly tap the brake pedal. When
the vehicle attains the desired
speed, push the toggle switch
down (SET-).
5-127
Driving your vehicle
Cruise Control will be canceled
• Moving the shift lever into N
To resume preset Cruising
when:
(Neutral). (for automatic transmis-
speed
sion/dual clutch transmission vehi-
cle)
• Decreasing the vehicle speed to
less than approximately 30 km/h
(20 mph).
• The ESC
(Electronic Stability
Control) is operating.
• Downshifting to the
2nd gear in
manual shift mode. (for automatic
transmission/dual clutch transmis-
sion vehicle)
OPDE056121
OPDE056120
•
Depressing the brake pedal.
i
Information
Push the toggle switch up (RES+). If
the vehicle speed is over 30 km/h (20
•
Depressing the clutch pedal.
Each of the above actions will cancel
(for manual transmission vehicle)
Cruise Control operation
(the SET
mph), the vehicle will resume the
preset speed.
indicator light in the instrument clus-
•
Pressing the O button located on
ter will go off), but only pressing the
the steering wheel.
button will turn the system off. If
•
Pressing the
button. Both the
you wish to resume Cruise Control
indicator and the SET indicator will
operation, push the toggle switch up
turn OFF.
(RES+) located on your steering
•
Pressing the
button. Both the
wheel. You will return to your previ-
indicator and the SET indicator
ously preset speed, unless the system
will turn OFF. (if equipped with the
was turned off using the
button.
Speed Limit Control)
5-128
To turn Cruise Control off
i
Information
The mode changes, as below, whenev-
er the
button is pressed.
System off
Cruise Control
Speed Limit Control
OPDE056118
5
• Press the
button (the
indi-
cator light will go off).
• Press the
button (The cruise
indicator light will go off.).
(if
equipped with Speed Limit Control)
- With the Cruise Control on,
pressing the button once will turn
Off the Cruise Control and turn
on the Speed Limit Control.
- With the Cruise Control off and
Speed Limit Control on, pressing
the button will turn off both sys-
tem.
5-129
Driving your vehicle
ADVANCED SMART CRUISE CONTROL SYSTEM (IF EQUIPPED)
WARNING
WARNING
For your safety, please read the
Take the following precautions :
owner's manual before using the
•
Always set the vehicle speed
Smart Cruise Control system.
under the speed limit in your
country.
•
If the Smart Cruise Control is
WARNING
left on,
(cruise
(
)
indicator light in the instru-
The Smart Cruise Control
ment cluster is illuminated)
OAE056097
System is not a substitute for
the Smart Cruise Control can
safe driving practices, but a
be activated unintentionally.
➀ Cruise indicator
convenience function only. It is
Keep the Smart Cruise
➁ Set speed
the responsibility of the driver
Control System off
(cruise
➂ Vehicle-to-vehicle distance
to always check the speed and
(
) indicator light
distance to the vehicle ahead.
OFF) when the Smart Cruise
Control is not in use, to avoid
The SCC screen will appear when
inadvertently setting a speed.
you select the Assist Mode tab on
the LCD display if the system is acti-
•
Use the Smart Cruise Control
vated.
System only when traveling
on open highways in good
weather.
The Smart Cruise Control System
(Continued)
allows you to program the vehicle to
maintain constant speed and dis-
tance detecting the vehicle ahead
without depressing the accelerator/
brake pedal.
5-130
Smart cruise control switch
(Continued)
•
Do not use the Smart Cruise
Control when it may not be
safe to keep the vehicle at a
constant speed:
- When driving in heavy traffic
or when traffic conditions
make it difficult to drive at a
constant speed
- When driving on rainy, icy, or
snow-covered roads
OPDE056115
- When driving on a steep
OPDE056123
i
Information
downhill or uphill
5
O : Cancels cruise control operation.
First, switch the mode to Smart
- When driving in windy areas
: Turns cruise control system on
Cruise Control by pressing the
- When driving in parking lots
or off.
button if equipped with the Speed
- When driving near crash
Limit Control System.
RES+: Resumes or increases cruise
barriers
control speed.
The mode changes, as below, whenev-
- When driving on a sharp
er the
button is pressed.
SET-: Sets or decreases cruise con-
curve
trol speed.
- When driving with limited
System off
Smart Cruise Control
: Sets vehicle-to-vehicle dis-
view (possibly due to bad
tance.
weather, such as fog, snow,
Speed Limit Control
rain or sandstorm)
- When the vehicle sensing
ability decreases due to
vehicle modification result-
ing level difference of the
vehicle's front and rear
5-131
Driving your vehicle
Smart Cruise Control speed
i
Information
To set Smart Cruise Control
Vehicle speed may decrease on an
speed
upward slope and increase on a down-
ward slope.
OPDE056119
3. Push the toggle switch down
(SET-). The Set Speed and
Vehicle-to-Vehicle Distance on the
OPDE056118
LCD display will illuminate.
1. Push the
button on the steer-
4. Release the accelerator pedal.
ing wheel to turn the system on.
The desired speed will automati-
The cruise (
) indicator
cally be maintained.
will illuminate.
If there is a vehicle in front of you, the
2. Accelerate to the desired speed.
speed may decrease to maintain the
The Smart Cruise Control speed
distance to the vehicle ahead.
can be set as follows:
On a steep grade, the vehicle may
• 30 km/h
(20 mph)~180 km/h
slow down or speed up slightly while
going uphill or downhill.
(110 mph) : when there is no
vehicle in front
• 0 km/h (0 mph)~180 km/h (110
mph) : when there is a vehicle in
front
5-132
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст