Hyundai Santa Fe (2006 year). Manual — part 164
INDICATORS AND GAUGES
BE -117
INSTRUMENT CLUSTER
COMPONENTS
E5E2EEB4
Connector C
Connector A
Connector A
Connector B
Connector C
Connector D
Connector B
Connector D
km/h
<STANDARD>
<SUPER VISION>
8
16
1
9
1
10
11
20
1
6
7
12
1
8
9
16
SCMBE6221L
BE -118
BODY ELECTRICAL SYSTEM
CONNECTOR A
CONNECTOR B
CONNECTOR C
CONNECTOR D
NO
CONNECTOR A
CONNECTOR B
CONNECTOR C
CONNECTOR D
1 Turn signal-right
Washer level
Door
P
2 ABS
Immobilizer
Trunk open
R
3 High beam(-)
ESP
PAB CUT OFF(-)
N
4 High beam(+)
ESP OFF
Air bag off(+)
D
5 -
Fuel GND(MICOM)
Air bag(-)
PWM signal(AT)
6 Fuel sender
Turn signal-left
EBD
-
7 Termperture sender
4WD LOCK
Battery charge
-
8 -
4WD
Brake
-
9 Oil level
Injection signal
seat belt
-
10 CHECK ENGINE
AMBIENT sensor
Oil pressure
-
11 Cruise
Trip computer mode sw
W/SEPERATOR
-
12 SET
Trip reset sw
Glow
Front left door
13 Power GND(-)
IGN2+
Front right door
14 -
GND(signal)
Rear left door
15 Illumination(+)
IGN+
Rear right door
16 Illumination(-)
Battery
-
17 High speed(BCM)
18 Speed signal
19 Tachometer signal
20 -
8
16
1
9
1
10
11
20
1
6
7
12
1
8
9
16
SCMBE6233L
INDICATORS AND GAUGES
BE -119
INSPECTION
E52DCCC6
SPEEDOMETER
1.
Adjust the pressure of the tires to the specified level.
2.
Drive the vehicle onto a speedometer tester.
Use
wheel chocks as appropriate.
3.
Check if the speedometer indicator range is within the
standard values.
CAUTION
Do not operate the clutch suddenly or increase/
decrease speed rapidly while testing.
NOTE
Tire wear and tire over or under inflation will increase
the indication error.
A
SCMBE6203L
[EXCEPT AUSTRALIA - KM/H]
Velocity
(km/h)
20
40
60
80
100
Tolerance
(km/h)
+4.6
+0.5
+5.1
+1.1
+6.6
+1.1
+7.1
+2.1
+7.6
+2.6
Velocity
(km/h)
120
140
160
180
220
Tolerance
(km/h)
+8.1
+3.1
+8.6
+3.6
+9.1
+4.1
+9.6
+4.6
+10.6
+5.5
[AUSTRALIA- KM/H]
Velocity
(km/h)
20
40
60
80
100
Tolerance
(km/h)
+2.9
-0.4
+2.9
-0.4
+4.0
-0.5
+4.4
-0.6
+4.3
-0.7
Velocity
(km/h)
120
140
160
180
220
Tolerance
(km/h)
+4.2
-0.8
+4.1
-0.9
+4.0
-1.0
+3.9
-1.1
+3.7
-1.3
[MPH]
Velocity
(MPH)
10
20
40
60
Tolerance
(MPH)
+2.6
+0.1
+2.9
+0.4
+3.7
+0.7
+4.0
+1.0
Velocity
(MPH)
80
100
120
140
Tolerance
(MPH)
+4.3
+1.3
+4.6
+1.6
+4.9
+1.9
+5.2
+2.2
VEHICLE SPEED SENSOR
1.
Connect the positive (+) lead from battery to terminal
2 and negative (-) lead to terminal 1.
2.
Connect the positive (+) lead from tester to terminal 3
and the negative (-) lead to terminal 1.
3.
Rotate the shaft.
4.
Check that there is voltage change from approx. 0V
to 11V or more between terminals 3 and 1.
5.
The voltage change should be 4 times for every revo-
lution of the speed sensor shaft.
If operation is not as specified, replace the sensor.
1
2
3
ETKD330A
BE -120
BODY ELECTRICAL SYSTEM
TACHOMETER
1.
Connect the scan tool to the diagnostic link connector
or install a tachometer.
2.
With the engine started, compare the readings of
the tester with that of the tachometer. Replace the
tachometer if the tolerance is exceeded.
CAUTION
a.
Reversing the connections of the tachometer
will damage the transistor and diodes inside.
b.
When removing or installing the tachometer,
be careful not to drop it or subject it to severe
shock.
Revolution
(rpm)
1,000
2,000
3,000
4,000
Re-
mark
Tolerance
(rpm)
±100
±125
±150
±150
Gaso-
line
Tolerance
(rpm)
±100
±125
±150
±150
Diesel
Revolution
(rpm)
5,000
6,000
7,000
-
Re-
mark
Tolerance
(rpm)
±150
±180
±210
-
Gaso-
line
Tolerance
(rpm)
±150
±180
-
-
Diesel
FUEL GAUGE
1.
Disconnect the fuel sender connector from the fuel
sender.
2.
Connect a 3.4 wattages, 12V test bulb to terminals 1
and 3 on the wire harness side connector.
3.
Turn the ignition switch to the ON, and then check that
the bulb lights up and the fuel gauge needle moves to
full.
3
5
2
4
1
IGN.
Fuel gauge
Battery
SCMBE6226L
FUEL GAUGE SENDER
1.
Using an ohmmeter, measure the resistance between
terminals 1 and 3 of sender connector (A) at each float
level.
F
1/2
A
3
5
2
4
1
Ω
Warning
lamp
E
SCMBE6227L
2.
Also check that the resistance changes smoothly
when the float is moved from "E" to "F".
Position
Resistance(Ω )
E
104.8 ± 1Ω
Warning lamp
89.9 ± 1Ω
1/2
13.7 ± 1Ω
Sender (F)
4.2 ± 1Ω
3.
If the height resistance is unsatisfied, replace the fuel
sender as an assembly.
CAUTION
After completing this test, wipe the sender dry
and reinstall it in the fuel tank.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст