Hyundai Santa Fe (2006 year). Manual — part 274
DS -56
DRIVESHAFT AND AXLE
REMOVAL
EC587D0E
1.
After making a match mark (C) on the rubber coupling
(A) and rear differential companion (B), remove the
propeller shaft mounting bolts (D).
Tightening torque Nm (kgf-m, lb-ft) :
49.0~68.6 (5~7, 36.2~50.6)
A
D
C
B
SCMDS6038D
2.
Remove the center bearing bracket (A) mounting bolts
(B).
Tightening torque Nm (kgf-m, lb-ft) :
39.2~49.0 (4~5, 28.9~36.2)
A
B
SCMDS6054D
3.
After making a match mark (C) on the flange yoke (A)
and transaxle companion (B), remove the propeller
shaft mounting bolts (D).
Tightening torque Nm (kgf-m, lb-ft) :
49.0~68.6 (5~7, 36.2~50.6)
B
C
D
A
SCMDS6510D
CAUTION
Use the hexagonal wrench to prevent damage of
bolt head when removing bolts (D).
4.
Installation is the reverse of the removal procedures
DIFFERENTIAL CARRIER ASSEMBLY
DS -57
DIFFERENTIAL CARRIER
ASSEMBLY
DIFFERENTIAL CARRIER (4WD)
COMPONENT
E7DDEA5A
1. Differential carrier
2. Pinion locking nut
3. Oil seal guide
4. Pinion oil seal
5. Outer pinion beaing
6. Pinion bearing spacer
7. Inner pinion bearing
10
14
17
16
10
14
15
16
13
12
18
10
11
20
19
21
11
15
9
8
7
6
5
4
3
2
1
8. Inner bearing adjust shim
9. Drive gear
10. Oil seal
11. Differential side bearing
12. Ring gear
13. Differential
14. Cam side gear
15. Pinion gear
16. Thrust washer
17. Differential pinion shaft
18. Differential cover
19. Differential cover mounting bolts
20. Breather
21. Filler plug
SCMDS6517L
DS -58
DRIVESHAFT AND AXLE
REMOVAL
EE8D3F42
1.
Drain the differential gear oil.
2.
Remove the rear drive shaft.
3.
Remove the propeller shaft.
4.
Support the differential assembly (A) with the jack (B).
A
B
SCMDS6056D
5.
Disconnect the coupling control connector (A).
A
KIQE600B
6.
After loosen the differential mounting bolts (A), and
remove the differential (B).
A
A
B
SCMDS6039D
7.
After loosen the cover bolts (A), and remove the dif-
ferential cover (B).
A
B
SCMDS6514D
DIFFERENTIAL CARRIER ASSEMBLY
DS -59
INSPECTION
E92AFA1B
Install the differential carrier assembly(A) with the special
tools(09517-43101
&
09517-43500).Then carry out the
following inspection.
A
09517
-43101
09517
-43500
KIQE610A
1.
Check the final drive gear backlash by the following
procedure.
1)
Place the drive pinion and move the drive gear to
check backlash is within the standard range.
NOTE
Measure at 4 points on the gear periphery.
Standard value :
0.10 ~ 0.15mm (0.0039 ~ 0.0059in.)
KIQE610B
2.
Check the drive gear back-face lash by the following
procedure.
1)
Place a dial gauge on the back-face of the drive
gear and measure the runout.
Limit : 0.05 mm (0.002 in)
KIQE610C
2)
If the runout is beyond the limit, check that there
are no foreign substances between the drive gear
and differential case and, that the bolts fixing the
drive gear are not loose.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст