Hyundai Santa Fe (2006 year). Manual — part 178
WINDSHIELD WIPER/WASHER
BE -173
INSPECTION
EBFE4E3A
1.
Install the wiper arm and blade to the specified posi-
tion.
Specified position
A
B
Distance
[in (mm)]
1.18 ± 0.2
(30 ± 5)
1.18 ± 0.2
(30 ± 5)
A
B
ATGE362C
2.
Set the washer nozzle on the specified spray position.
455.5
300.5
120
150
318.5
374
330.5
340.5
374.5
318
280.5
109 81
434
Unit : mm
SCMBE6345L
BE -174
BODY ELECTRICAL SYSTEM
FRONT WASHER MOTOR
INSPECTION
E40BA24E
1.
With the washer motor connected to the reservoir
tank, fill the reservoir tank with water.
2.
Connect positive (+) battery cables to terminal 1 and
negative (-) battery cables to terminal 2 respectively.
3.
Check that the motor operates normally and the
washer motor runs and water sprays from the front
nozzles.
4.
If they are abnormal, replace the washer motor.
1. Windshield washer (+)
2. Ground
1. Windshield washer (+)
2. Ground
3. Rear washer (+)
1
2
3
[Front & Rear washer]
[Front washer]
1
2
SCMBE6348L
<Windshield & Rear washer motor>
Washer switch
Front
Rear
2
3
M
M2
M1
1
SCMBE6349L
[ Windshield washer motor ]
Washer motor
M
2
1
SCMBE6346L
WASHER FLUID LEVEL SENSOR SWITCH
1.
Disconnect the negative(-) battery terminal.
2.
Drain the washer fluid less than 650 cc.
3.
Check for continuity between the No. 1 and No.2 ter-
minal in each float position.
There should be continuity when the float is down.
There should be no continity when the folat is up.
4.
If the continuity is not as specified, replace the washer
fluid level switch
+ -
SCMBE6352D
1
Over 650cc
Under 650cc
2
Terminal
Position
(Tolerance : -50cc ~ +100cc)
SCMBE6353L
WINDSHIELD WIPER/WASHER
BE -175
REPLACEMENT
EF02B9DF
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front bumper cover. (Refer to Body group
- Front bumper)
3.
Remove the washer hose (A) and the washer motor
connector (B).
A
B
SCMBE6335D
4.
Disconnect the washer fluid level sensor switch con-
nector (A).
A
SCMBE6346D
5.
Remove the washer reservoir after removing 3 bolts.
SCMBE6347D
6.
Installation is the reverse of removal.
BE -176
BODY ELECTRICAL SYSTEM
RAIN SENSOR
CIRCUIT DIAGRAM
E27A55E1
High
Low
Low
High
INT/AUTO
OFF
Washer
IGN
IGN
IGN
IGN
IGN
Wiper
motor
Washer
motor
Blank
Washer
AUTO Signal
Parking brake
RAINSENSOR
Low 8
High 7
IGN 5
1
3
4
2
6
1
2
3
4
5
6
7
8
2
8
7
4
3
6
Washer
Low
OFF
High
AUTO/INT
Terminal
Position
SCMBE6337L
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст