Hyundai Santa Fe (2006 year). Manual — part 136
GENERAL
BE -5
9.
Check for loose retainer (A) and rubber seals (B).
A
A
B
ETKD150E
10. The backs of some connectors are packed with
grease. Add grease if necessary. If the grease (A) is
contaminated, replace it.
A
ETKD150F
11. Insert the connector all the way and make sure it is
securely locked.
12. Position wires so that the open end of the cover faces
down.
DOWN
ETKD150G
HANDLING WIRES AND HARNESSES
1.
Secure wires and wire harnesses to the frame with
their respective wire ties at the designated locations.
2.
Remove clips carefully; don’t damage their locks (A).
A
ETKD150H
3.
Slip pliers (A) under the clip base and through the hole
at an angle, and then squeeze the expansion tabs to
release the clip.
A
ETKD150I
4.
After installing harness clips, make sure the harness
doesn’t interfere with any moving parts.
5.
Keep wire harnesses away from exhaust pipes and
other hot parts, from sharp edges of brackets and
holes, and from exposed screws and bolts.
BE -6
BODY ELECTRICAL SYSTEM
6.
Seat grommets in their grooves properly (A). Do not
leave grommets distorted (B).
A
B
ETKD150J
TESTING AND REPAIRS
1.
Do not use wires or harnesses with broken insulation.
Replace them or repair them by wrapping the break
with electrical tape.
2.
After installing parts, make sure that no wires are
pinched under them.
3.
When using electrical test equipment, follow the man-
ufacturer’s instructions and those described in this
manual.
4.
If possible, insert the remover tool from the wire side
(except waterproof connector).
ETKD150K
5.
Use a probe with a tapered tip.
Refer to the user’s guide in the wiring repair kit (Pub
No. : TRK 015.)
ETKD150L
FIVE-STEP TROUBLESHOOTING
1.
Verify the complaint
Turn on all the components in the problem circuit to
verify the customer complaint. Note the symptoms.
Do not begin disassembly or testing until you have
narrowed down the problem area.
2.
Analyze the schematic
Look up the schematic for the problem circuit.
Determine how the circuit is supposed to work by trac-
ing the current paths from the power feed through the
circuit components to ground. If several circuits fail at
the same time, the fuse or ground is a likely cause.
Based on the symptoms and your understanding of
the circuit operation, identify one or more possible
causes of the problem.
3.
Isolate the problem by testing the circuit.
Make circuit tests to check the diagnosis you made in
step 2. Keep in mind that a logical, simple procedure
is the key to efficient troubleshooting.
Test for the most likely cause of failure first. Try to
make tests at points that are easily accessible.
4.
Fix the problem
Once the specific problem is identified, make the re-
pair. Be sure to use proper tools and safe procedures.
5.
Make sure the circuit works
Turn on all components in the repaired circuit in all
modes to make sure you’ve fixed the entire problem.
If the problem was a blown fuse, be sure to test all of
the circuits on the fuse. Make sure no new problems
turn up and the original problem does not recur.
AUDIO SYSTEM
BE -7
AUDIO SYSTEM
SPECIFICATION
EDB048F2
AUDIO
Item
Specification
Model
RADIO/CD
(M445)
RADIO / TAPE /
CD/MP3 (M455)
RADIO / TAPE / 6CDC
/ MP3 (M465)
RADIO / 6CDC /
MP3 (D466)
Power supply
DC 14.4V
Rated output
Max 43W x 4
Max 3.2Vrms
Max 4.5Vrms
Antenna
80PF 75Ω
Tuning type
PLL synthesized type
FM
87.5 ~ 108.0 MHz/100 KHz (General), 50KHz(Europe)
AM
531 ~ 1602 KHz/9 KHz (General)
MW
522 ~ 1620 KHz/9 KHz (Europe)
Frequency range /
Channel space
LW
153 ~ 279 KHz/1 KHz (Europe)
SPEAKER & EXTERNAL AMPLIFIER
Item
M445
(Internal
Amplifier)
M455
M465
D466
Front
50
50
50
40
Rear
50
50
50
40
Tailgate
-
-
-
32
Tweeter
50
50
50
20
Front center
-
-
-
32
Input Power
(W)
Sub woofer
-
-
50
64
Front
3.4 ± 0.5
3.4 ± 0.5
2 ± 0.3
2 ± 0.4
Rear
3.4 ± 0.5
3.4 ± 0.5
2 ± 0.3
2 ± 0.4
Tailgate
-
-
-
2.15 ± 0.25
Tweeter
3.4 ± 0.5
3.4 ± 0.5
3.4 ± 0.5
4 ± 0.8
Front center
-
-
-
2.15 ± 0.25
Speaker
Impedance
(Ω )
Sub woofer
-
-
2 ± 0.3
1.4 ± 0.25
Speaker Number
6
6
7
10
Power supply
DC 14.4V
DC 14.4V
DC 14.4V
DC 14.4V
Output power
MAX 43W x 4
MAX 43W x 4
MAX 310W (55W
x 4CH + 45W
x 2CH)
MAX 660W (55W
x 12CH)
External Amplifier
Speaker
Impedance (Ω )
4Ω x 4
4Ω x 4
2Ω x 5 + 3.4Ω x 2
2Ω x 5 + 3.4Ω
x 2 + 1.4V
BE -8
BODY ELECTRICAL SYSTEM
COMPONENT LOCATION
E713F673
5
2
2
6
8
10
7
5
6
7
1
3
4
1. Audio unit
2. Tweeter speaker
3. External amplifier
4. Roof antenna
5. Front door speaker
6. Rear door speaker
7. Tailgate speaker
8. Sub-woofer speaker
9. Antenna feeder cable
10. 6CD changer
11. Crash pad center speaker
11
This illustration shows the LHD type.
RHD type is symmetrical.
SCMBE6001L
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст