Hyundai Santa Fe (2006 year). Manual — part 100
ATA -158
AUTOMATIC TRANSAXLE (A5HF1)
13. Tighten the transaxle insulator mounting bolt (A).
TORQUE:
90~110 Nm(9~11 kgf.m, 65.1~79.5 lb-ft)
A
SCMAT6015D
14. Tighten the transaxle mounting bolts (A).
TORQUE:
43~55 Nm(4.3~5.5 kgf.m, 31.1 ~ 39.7 lb-ft)
A
AKKF002O
15. Remove the SST (09200-38001) holding the engine
and transaxle assembly.
09200-38001
SCMAT6014D
16. Install the starter motor. (see EE group).
TORQUE:
65~85 Nm(6.5~8.5 kgf.m, 47.0~61.5 lb-ft)
17. Connect the power steering pressure tube (A) to the
power steering oil pump.
A
SCMAT6018D
18. Connect the transaxle oil cooler hoses (A) to the tubes
by fastening the clamps (B).
A
B
SCMAT6013D
AUTOMATIC TRANSAXLE SYSTEM
ATA -159
19. Install the control cable assembly(C) by tightening the
nut (A) and clip (B).
TORQUE:
10~14 Nm(1.0~1.4 kgf.m, 7.2~10.1 lb-ft)
A
C
B
SCMAT6012D
20. Connect the transaxle wire harness connectors.
1)
Install the inhibiter switch connector (A).
A
SCMAT6007D
2)
Install the solenoid valve connector (A).
A
SCMAT6008D
3)
Install the input speed sensor connector (A).
A
SCMAT6009D
4)
Install the output speed sensor connector (A).
A
SCMAT6010D
ATA -160
AUTOMATIC TRANSAXLE (A5HF1)
5)
Install the vehicle speed sensor connector (A).
A
SCMAT6011D
21. Install the battery tray (B) by tightening the four mount-
ing bolts (A).
A
B
SCMAT6006D
22. Install the air cleaner lower part (B) by installing the
two mounting bolts (A).
A
B
SCMMT6004D
23. Install the air cleaner upper cover (B) by fastening the
clamp bolt (A) and the clips.
A
B
SCMMT6060D
24. Connect the AFS connector (A).
A
SCMMT6002D
25. Install the battery (A).
A
SCMAT6001D
AUTOMATIC TRANSAXLE SYSTEM
ATA -161
26. Refill the transaxle fluid. (see ’Service adjustment
procedure’)
27. Refill the power steering fluid. (see ’ST’ group)
CAUTION
After installing the inter cooler assembly, bleed
the air in the system.
28. Install the engine cover and the inter cooler assembly.
(see ’EM’ group)
NOTE
When replacing the automatic transaxle, reset the au-
tomatic transaxle’s values by using the High- Scan
Pro.
a.
Connect the Hi-Scan Pro connector to the data link
connector under the crash pad and power cable to
the cigar jack under the center facia.
b.
Turn the ignition switch on and power on the Hi-Scan
Pro.
c.
Select the vehicle’s name.
d.
Select ’AUTOMATIC TRANSAXLE’.
SCMAT6511L
e.
Select ’RESETTING AUTO T/A VALUES’ and perform
the procedure.
SCMAT6512L
f.
Perform the procedure by pressing F1 (REST).
SCMAT6513L
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст