Hyundai Santa Fe (2006 year). Manual — part 543
FLA -238
FUEL SYSTEM
DTC P0131 HO2S CIRCUIT LOW VOLTAGE (BANK 1 / SENSOR 1)
COMPONENT LOCATION
E5E16663
HO2S [Bank 1/Sensor 1]
LGLG504A
GENERAL DESCRIPTION
E9CECC3F
In order to control emissions of the CO, HC and NOx components of the exhaust gas, heated oxygen sensor (HO2S),
mounted on the front side and rear side of catalytic converter, detects the oxygen content in the exhaust gas. The front
HO2S signal is used to control air/fuel ratio (closed loop fuel control) and the rear HO2S signal is used to monitor front
HO2S and catalyst for proper operation. The HO2S requires a minimum temperature to operate properly and provide a
closed loop fuel control system. The HO2S contains the heater element to reduce its warming-up time and ensure its
performance during all driving conditions. The oxygen sensor generates a voltage that indicates the difference between
the oxygen content of the exhaust stream and the oxygen content of ambient air. When the exhaust stream is “ rich,”
there is more oxygen in the ambient air than in the exhaust stream, so the voltage will be higher.
DTC DESCRIPTION
E8D2EB10
Checking output signals from HO2S under detecting condition, if an output signal is below 0.04V for more than predeter-
minate time, PCM sets P0131. MIL(Malfunction Indication Lamp) turns on when the malfunction lasts till consecutive 2
driving cycle.
DTC DETECTING CONDITION
E2DEFF6E
Item
Detecting Condition
Possible cause
DTC Strategy
• Monitor signal voltage
Enable Conditions
• Battery voltage ≥ 10V
• Engine running ≥ 60 sec.
• Engine warm-up state
Threshold value
• The voltage of HO2S(B1/S1) < 0.04V
Diagnosis Time
• Continuous
(more than 12.5 sec. failure for every 15 sec.test)
MIL On Condition
• 2 Driving Cycles
• Poor Connection
• Short to ground in harness
• HO2S(B1/S1)
• PCM
DTC TROUBLESHOOTING PROCEDURES
FLA -239
SPECIFICATION
EB86DDBC
(REFERENCE ONLY)
Test Condition
HO2S Voltage(Sensor1)
HO2S Voltage(Sensor2)
HO2S Signal
at idle after warm-up
Signal is commonly switching
from rich to lean more than 3
times in 10 sec.
Signal is commonly above 0.6V.
HO2S signal at open circuit
(Pumping current OFF)
Approx. 0.45V
HO2S signal at open circuit
(Pumping current ON)
Approx.
3.5V
FLA -240
FUEL SYSTEM
SCHEMATIC DIAGRAM
E57946F9
HO2S [Bank 1/Sensor 1]
HO2S [Bank 2/Sensor 1]
PCM
C91-1,2
C30-B
PCM (C30-B)
HO2S [B1/S1] (C91-1)
1
2
1
21
2
22
3
23
4
24
5
25
6
26
7
27
8
28
9
29
10
30
11
31
12
32
13
33
14
34
15
35
16
36
17
37
18
38
19
39
20
40
41
61
42
62
43
63
44
64
45
65
46
66
47
67
48
68
49
69
50
70
51
71
52
72
53
73
54
74
55
75
56
76
57
77
58
78
59
79
60
80
Battery Voltage (B+)
Main Relay
3
4
PCM C30-B (30)
HO2S [B1/S1] Signal
Sensor ground
PCM C30-B (49)
Main Relay
3
4
1
2
49 - HO2S [B1/S1] Signal
30 - GND
70 - Heater [B1/S1] Control
HO2S [B2/S1] (C91-2)
Main Relay
3
4
1
2
51 - HO2S [B2/S1] Signal
28 - GND
67 - Heater [B2/S1] Control
HO2S [B1/S2] (C91-3)
Main Relay
3
4
1
2
50 - HO2S [B1/S2] Signal
31 - GND
74 - Heater [B1/S2] Control
HO2S [B2/S2] (C91-4)
Main Relay
3
4
1
2
52 - HO2S [B2/S2] Signal
29 - GND
73 - Heater [B2/S2] Control
1
2
3
4
PCM C30-B (28)
HO2S [B2/S1] Signal
Sensor ground
PCM C30-B (51)
Battery Voltage (B+)
Main Relay
PCM C30-B (67)
Heater
[B2/S1] Control
1
2
3
4
PCM C30-B (31)
HO2S [B1/S2] Signal
Sensor ground
PCM C30-B (50)
Battery Voltage (B+)
Main Relay
PCM C30-B (74)
Heater
[B1/S2] Control
1
2
3
4
PCM C30-B (29)
HO2S [B2/S2] Signal
Sensor ground
PCM C30-B (52)
Battery Voltage (B+)
Main Relay
PCM C30-B (73)
Heater
[B2/S2] Control
[CIRCUIT DIAGRAM]
[HARNESS CONNECTORS]
[CONNECTION INFORMATION]
Terminal
Connected to
Function
Terminal
Connected to
Function
Terminal
Connected to
Function
Terminal
Connected to
Function
HO2S [B1/S1]
HO2S [B2/S1]
HO2S [B1/S2]
HO2S [B2/S2]
PCM C30-B (70)
Heater
[B1/S1] Control
HO2S [Bank 1/Sensor 2]
HO2S [Bank 2/Sensor 2]
C91-3,4
2
1
4
3
1
2
3
4
SCMF16110L
DTC TROUBLESHOOTING PROCEDURES
FLA -241
SIGNAL WAVEFORM AND DATA
E59FF425
Fig) Signal waveforms of front HO2S(the upper) and rear HO2S(the lower)
SCMF16223L
After warming-up, if accelerator pedal is released suddenly around 4000rpm, the HO2S signal reading will be lower than
200mV resulting from Fuel cut-off for the moment. Conversely, if suddenly accelerator pedal is depressed, HO2S signal
reading will be around 0.6V ~1.0V. At idle, Normally HO2S signal will switch from lean to rich with 3 Hz. And as racing,
Its frequency rises.
MONITOR DTC STATUS
EFA6B287
1.
Check DTC Status
1)
Connect scantool to Data Link Connector(DLC).
2)
IG "ON".
3)
Select "Diagnostic Trouble Codes(DTCs)" mode, and then Press F4(DTAL) to check DTC’s information from the
DTCs menu
4)
Read "DTC Status" parameter.
SCMF16159L
5)
Is parameter displayed "Present fault"?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст