Hyundai Santa Fe (2006 year). Manual — part 585
FLA -406
FUEL SYSTEM
4.
Monitor that all rediness test have been verified as " Complete "
5.
Are any DTCs present ?
YES
▶ Go to the applicable troubleshoooting procedure.
NO
▶ System is performing to specification at this time.
DTC TROUBLESHOOTING PROCEDURES
FLA -407
DTC P0445 EVAP. EMISSION SYSTEM-PURGE CTRL. VALVE CIRCUIT
SHORTED
COMPONENT LOCATION
EA49A992
Refer to DTC P0444.
GENERAL DESCRIPTION
E67CE4F2
Refer to DTC P0444.
DTC DESCRIPTION
E00E371F
Checking output signals from PCSV every 10 sec. under detecting condition, if signals indicating short to battery in the
circuit are detected for more than 5 sec., PCM sets P0445. MIL(Malfunction Indication Lamp) turns on when the malfunc-
tion lasts till consecutive 2 driving cycle.
DTC DETECTING CONDITION
E9146E29
Item
Detecting Condition
Possible cause
DTC Strategy
• Short to battery
EnableConditions
• Engine running state
• 11V ≤ Battery voltage ≤ 16V
• Above enable conditions are met > 0.5 sec.
Threshold value
• Short to battery
DiagnosisTime
• Continuous
(More than 5 sec.failure for every 10 sec.test)
MIL On Condition
• 2 driving cycles
• Poor connection
• Short to battery in harness
• PCSV
• PCM
SPECIFICATION
EF7575BD
Refer to DTC P0444.
SCHEMATIC DIAGRAM
E71171CC
Refer to DTC P0444.
SIGNAL WAVEFORM
E219B974
Refer to DTC P0444.
MONITOR DTC STATUS
ED8A58B2
Refer to DTC P0444.
TERMINAL AND CONNECTOR INSPECTION
EF9207D3
Refer to DTC P0444.
FLA -408
FUEL SYSTEM
CONTROL CIRCUIT INSPECTION
E96A7FBB
1.
IG "OFF" and disconnect PCSV connector.
2.
IG "ON" and ENG "OFF"
3.
Measure voltage between terminal 2 of PCSV harness connector and chassis ground.
Specification : Approx. 0.5V
4.
Is the measured voltage within specification?
YES
▶ Go to "Component Insepction" procedure.
NO
▶ Repair short to battery in harness, and go to " Verification of Vehicle Repair" procedure.
COMPONENT INSPECTION
E5DDBC8E
1.
Check PCSV
1)
IG "OFF" and disconnect PCSV connector.
2)
Measure resistance between terminals 1 and 2 of PCSV connector.(Component side)
SPECIFICATION :
Item
Coil resistance(Ω )
PCSV
14.0 ~ 18.0Ω [20℃( 68℉)]
C94
2
1
SCMF16356L
3)
Is the measured resistance within specification?
YES
▶ Substitute with a known - good PCM and check for proper operation.
▶ If the problem is corrected, replace PCM and go to "Verification of Vehicle Repair" procedure.
NO
▶ Substitute with a known - good PCSV and check for proper operation.
▶ If the problem is corrected, replace PCSV and go to "Verification of Vehicle Repair" procedure.
DTC TROUBLESHOOTING PROCEDURES
FLA -409
NOTE
There is a memory reset function on scantool that can erase optional parts automatically detected and memorized
by PCM. After testing PCM on the vehicle, use this function to reuse the PCM on the others
VERIFICATION OF VEHICLE REPAIR
E86F6EB7
Refer to DTC P0444.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст