Hyundai Tucson (2022 year). Manual in english — page 8
Convenient features
Closing the hood
Liftgate
1.
Before closing the hood, check in and
Opening the liftgate
around the engine compartment to
ensure the following:
--
Any tools or other loose objects
are removed from the engine room
area or hood opening area
--
All glove, rags, or other
combustible material is removed
from the engine compartment
--
All filler caps are tightly and
correctly installed
2.
Return the hood support rod to its clip
ONX4050023
to prevent it from rattling.
Make sure the vehicle is in P (Park) and
3.
Lower the hood until it is about 30 cm
set the parking brake.
(12in.) above the closed position and
Then do one of the following:
let it drop. Make sure that it locks into
place.
1.
Unlock all doors with the Door Unlock
button on your remote key or smart
4.
Check that the hood has engaged
key. Press the liftgate handle button
properly. If the hood can be raised
and open the liftgate.
slightly, it is not properly engaged.
Open it again and close it with a little
2.
Press and hold the liftgate open
more force.
button on the remote key or smart
key. Press the liftgate handle button
and open the liftgate.
WARNING
3.
With the Smart Key in your
•
Before closing the hood, ensure
possession, press the liftgate handle
all obstructions are removed from
button and open the liftgate.
around the hood opening.
•
Always double check to be sure that
the hood is firmly latched before
driving away. Check there is no
hood open warning light or message
displayed on the instrument cluster.
Driving with the hood opened may
cause a total loss of visibility, which
might result in an accident.
•
Do not move the vehicle with the
hood in the raised position, as vision
is obstructed, which might result in
an accident, and the hood could fall
or be damaged.
5-66
05
Closing the liftgate
WARNING
ONX4E050057R
ONX4E050058R
Lower the liftgate lid and press down
Do not grab or hold on to the liftgate
until it locks. To be sure the liftgate lid is
support struts at any time. Damage to
securely fastened, always check by trying
the liftgate support struts could result.
to pull it up again without pressing the
Deformation of the liftgate support
liftgate handle button.
struts may cause vehicle damage and
personal injury may occur.
WARNING
Always keep the liftgate completely
WARNING
closed while the vehicle is in motion. If
• NEVER allow anyone to occupy the
it is left open or ajar, poisonous exhaust
luggage compartment of the vehicle
gases containing carbon monoxide
at any time. If the liftgate is partially
(CO) may enter the vehicle and serious
or totally latched and the person
illness or death may result.
is unable to get out, serious injury
or death could occur due to lack
NOTICE
of ventilation, exhaust fumes and
rapid heat build-up, or because of
To prevent damage to the liftgate
exposure to cold weather conditions.
support struts and the attached
The luggage compartment is also
hardware, always close the liftgate
a highly dangerous location in the
before driving.
event of a crash because it is not a
protected occupant space but is a
Information
part of the vehicle’s crush zone.
In cold and wet climates, liftgate lock
• Your vehicle should be kept locked
and liftgate mechanisms may not work
and keys should be kept out of
properly due to freezing conditions.
the reach of children. Parents
should teach their children about
the dangers of playing in luggage
compartments.
5-67
Convenient features
Emergency liftgate safety release
Power liftgate (if equipped)
The power liftgate open/close button
automatically opens and closes the
liftgate.
Before using the power liftgate
The power liftgate operates when the
gear is in P (Park) with the Engine Start/
Stop button in the ON position. However,
the liftgate will operate regardless of the
gear position when the engine is off.
For safety, before attempting to open or
ONX4E050059R
close the liftgate, make sure the vehicle
Your vehicle is equipped with the
is in P (Park).
emergency liftgate safety release lever
located on the bottom of the liftgate.
When someone is inadvertently locked
WARNING
in the luggage compartment, the liftgate
• Never leave children unattended
can be opened by moving the lever in the
in your vehicle. Children might
direction of the arrow and pushing the
operate the power liftgate. Doing so
liftgate open.
could result in injury to themselves
or others, and could damage the
vehicle.
WARNING
• Make sure there are no people or
• For emergencies, be fully aware
objects around the liftgate before
of the location of the emergency
operating the power liftgate. Wait
liftgate safety release lever in the
until the liftgate is opened fully and
vehicle and how to open the liftgate
stopped before loading or unloading
if you are accidentally locked in the
cargo or passengers from the
luggage compartment.
vehicle.
• No one should be allowed to occupy
the luggage compartment of the
NOTICE
vehicle at any time. The luggage
compartment is a very dangerous
Do not close or open the power
location in the event of a crash.
liftgate manually. This may cause
• Use the release lever for
damage to the power liftgate. If it is
emergencies only. Use with extreme
necessary to close or open the power
caution, especially while the vehicle
liftgate manually when the battery is
is in motion.
discharged or disconnected, do not
apply excessive force.
5-68
05
Opening the power liftgate
ONX4050028
ONX4E050144
• Press the power liftgate button for
approximately one second.
The power liftgate will open
automatically by doing one of the
To stop operation of the power liftgate
following:
while it is in motion, quickly press the
power liftgate button on the dash or on
• Press the liftgate button on the
your remote key or smart key.
remote key or smart key for
approximately one second.
ONX4050027
• Press the liftgate handle button
while having the smart key in your
possession.
5-69
Convenient features
Closing the power liftgate
ONX4050028
ONX4E050144
•
To close the power liftgate from inside
the vehicle, press and hold the Power
• Press the liftgate open/close button
Liftgate button on the dash. You must
on the key and hold until the liftgate is
continue to hold the button until the
fully closed.
liftgate is completely closed. Buzzer
• Releasing the liftgate open/close
sounds continuously during the
button on the key stops liftgate
closing operation. If you release the
movement with the buzzer sound
button, the liftgate motion will stop
approximately for 5 seconds.
and a continuous beeping will sound
• To stop operation of the power liftgate
for about 5 seconds.
while it is in motion, quickly press the
•
To stop operation of the power
power liftgate button on the dash or
liftgate while it is in motion, quickly
on your remote key or smart key.
press the power liftgate button on the
dash or on your remote key or smart
key.
NOTICE
Remain near your vehicle while closing
the liftgate with the remote key or
smart key.
If you exceed the distance limit of the
smart key or remote key while the
liftgate is in motion, the liftgate will
stop and a continuous beeping will
sound for about 5 seconds.
ONX4E050062R
• Press the power liftgate inner button
for approximately one second when
the liftgate is opened. The liftgate will
close and lock automatically.
5-70
05
Automatic reverse
Non-operating conditions of the
power liftgate
•
The power liftgate does not open
when the vehicle is in motion.
The chime will sound if you drive
over 2mph (3km/h) with the
liftgate opened. Stop your vehicle
immediately at a safe place and check
if your liftgate is opened.
•
Operating the power liftgate more
than 5 times continuously could
cause damage to the operating motor.
ONX4E050030
If this occurs, the power liftgate
During power opening and closing if the
system enters into thermal protection
power liftgate is blocked by an object or
mode to prevent the motor from
part of the body, the power liftgate will
overheating. In thermal protection
detect the resistance.
mode, the power liftgate will not
operate. If any of the power liftgate
• If the resistance is detected while
buttons are pressed to try to open the
opening the liftgate, it will stop and
liftgate, the chime will sound 3 times
move in the opposite direction.
but the liftgate will not operate.
• If the resistance is detected while
Allow the power liftgate system
closing the liftgate, it will stop and
to cool for about 1 minute before
move in the opposite direction.
operating the system again.
•
The power liftgate can be operated
However, if the resistance is weak such
when the engine is not running.
as from an object that is thin or soft, or
However the power liftgate operation
the liftgate is near the latched position,
consumes large amounts of vehicle
the automatic stop and reversal may not
electric power. To prevent the battery
detect the resistance. If the automatic
from being discharged, do not
reversal feature operates continuously
operate it excessively e.g.: more than
more than twice during opening or
approximately 10 times repeatedly.
closing operation, the power liftgate may
•
To prevent the battery from being
stop at that position. At this time, close
discharged, do not leave the power
the liftgate manually and operate the
liftgate in the open position for a long
liftgate automatically again.
lime.
•
When jacking up the vehicle to
WARNING
change a tire or repair the vehicle, do
not operate the power liftgate. This
Never intentionally place any object
could cause the power liftgate to
or part of your body in the path of
operate improperly.
the power liftgate to make sure the
automatic reverse function operates.
•
In cold and wet climates, the power
liftgate may not work properly due to
freezing conditions.
NOTICE
Do not put heavy objects on the power
liftgate before you operate the power
liftgate. Additional weight may damage
the operation of the system.
5-71
Convenient features
Resetting the power liftgate
WARNING
ONX4E050145
ONX4E050058R
If the battery has been discharged or
Do not grab or hold on to the liftgate
disconnected, or if the power liftgate
support struts at any time. Damage to
fuse has been replaced or removed, reset
the liftgate support struts could result.
the power liftgate by performing the
Deformation of the liftgate support
following procedure:
struts may cause vehicle damage and
1. Put the gear in P (Park).
personal injury may occur.
2. Press the power liftgate inner button
(B) and the power liftgate handle
User Settings for the Power Liftgate
switch (A) simultaneously for more
From the Infotainment Screen
than 3 seconds. The chime will sound.
The driver can select the power liftgate
3. Close the liftgate manually.
opening height or speed from the
Settings menu in the infotainment
If the power liftgate does not work
system screen.
properly after the above procedure, we
recommend that the system be checked
by an authorized HYUNDAI dealer.
Information
If the power liftgate does not operate
normally, check again if the gear position
is in right position.
OJX1050111N
Power liftgate opening height
To adjust the power liftgate opening
height, select ‘Setup → Vehicle Settings →
Door/Liftgate → Power Liftgate Opening
Height → Full Open/Level 3/Level 2/Level
1/User Height Setting’.
See additional information in supplied
Infotainment Manual.
5-72
05
If ‘User Height Setting’ is selected, follow
Emergency liftgate safety release
the instructions below to set the height
of the power liftgate manually.
1. Position the liftgate manually to the
height you prefer.
2. Press the power liftgate open/close
button located inside the liftgate for
more than 3 seconds.
3. Close the liftgate manually after
hearing the buzzer sound.
4. The liftgate will open to the manually
adjusted height that was set.
ONX4E050059R
Your vehicle is equipped with the
WARNING
emergency liftgate safety release lever
located on the bottom of the liftgate
Always keep the liftgate completely
inside the vehicle.
closed while the vehicle is in motion. If
it is left open or ajar, poisonous exhaust
When someone is inadvertently locked
gases containing carbon monoxide
in the luggage compartment, the liftgate
(CO) may enter the vehicle and serious
can be opened by moving the lever in the
illness or death may result.
direction of the arrow and pushing the
liftgate open.
WARNING
WARNING
Occupants should never ride in the
rear cargo area where no restraints are
• Be aware of the location of the
available. To avoid injury in the event of
emergency liftgate safety release
an accident or sudden stops, occupants
lever in your vehicle and know how
should always be properly restrained.
to open the liftgate using the safety
release lever.
• No one should be allowed to occupy
the luggage compartment of the
vehicle at any time. The luggage
compartment is a very dangerous
location in the event of a crash.
• Use the release lever for emergencies
only. Use extreme caution, especially
while the vehicle is in motion.
5-73
Convenient features
Smart liftgate (if equipped)
1. Settings
To activate the Smart Liftgate, go to
User Settings Mode and select Smart
Liftgate on the LCD display.
2. Detect and Alert
The smart liftgate detecting area
extends approximately 20~40 in.
(50~100 cm) behind the vehicle. If you
are positioned in the detecting area
and are carrying the smart key, the
hazard warning lights will blink and
the chime will sound to alert you that
ONX4E050063R
the smart liftgate will open.
On a vehicle equipped with a smart key,
the liftgate can be opened with hands-
Information
free activation using the smart liftgate
system.
Do not approach the detecting area if you
do not want the liftgate to open. If you
Using smart liftgate
have unintentionally entered the detecting
area and the hazard warning lights and
The hands-free smart liftgate system
chime starts to operate, move away from
can be opened automatically when the
the area behind the vehicle with the smart
following conditions are met:
key. The liftgate will remain closed.
• The smart liftgate option is enabled in
the Settings menu in the infotainment
3.
Automatic opening
system screen.
After the hazard warning lights blink
• The smart liftgate is activated and
and the chime sounds 6 times, the
ready 15 seconds after all the doors
smart liftgate will open.
are closed and locked.
• The smart liftgate will open when
the smart key is detected in the area
behind the vehicle for 3 seconds.
Information
The smart liftgate will NOT operate when:
• A door is not locked or closed.
• The smart key is detected within
15 seconds from when the doors were
closed and locked.
• The smart key is detected within
15 seconds after the doors are closed
and locked, and within 60 in. (1.5
m) from the front door handles. (for
vehicles equipped with Welcome Light).
• The smart key is in the vehicle.
5-74
05
Deactivating smart liftgate
Detecting area
Type A
Type B
OTMA050009
OTMA050010
ONX4050032N
1. Door lock
•
The smart liftgate detecting area
extends approximately 20~40 in.
2. Door unlock
(50~100 cm) behind the vehicle. If
3. Liftgate open (Liftgate)
you are positioned in the detecting
Liftgate open / close (Power liftgate)
area and are carrying the smart key,
the hazard warning lights will blink
If you press any button on the smart key
and the chime will sound for about 3
during the Detect and Alert stage, the
seconds to alert you that the liftgate
smart liftgate will be deactivated.
will open.
Make sure to be aware of how to
•
The alert stops once the smart key is
deactivate the smart liftgate for
moved outside of the detecting area
emergency situations.
within the 3 second period.
• If you press the door unlock button
(2), the smart liftgate will be
Information
deactivated temporarily. But, if you do
not open any door for 30 seconds, the
•
Smart liftgate may not operate
smart liftgate will be activated again.
properly if any of the following occur:
--
The smart key is close to a radio
• If you press the liftgate open button
(3) for more than 1 second, the liftgate
transmitter such as a radio station or
an airport which can interfere with
opens.
normal operation of the transmitter.
• The smart liftgate will still be activated
if you press the door lock button (1) or
--
The smart key is near a mobile two
liftgate open/close button (3) on the
way radio system or a mobile phone.
smart key as long as the smart liftgate
--
Another vehicle’s smart key is being
is not already in the Detect and Alert
operated close to your vehicle.
stage.
•
Smart liftgate detecting area may
• In case you have deactivated the
change when:
smart liftgate by pressing the smart
--
The vehicle is parked on an incline
key button and opened a door, the
or slope.
smart liftgate can be activated again
--
One side of the vehicle is raised or
by closing and locking all doors.
lowered relative to the opposite side.
5-75
Convenient features
Fuel filler door
Information
Opening the fuel filler door
The fuel filler door will unlock when
Driver’s door is unlocked.
To unlock fuel filler door:
• Press the unlock button on your smart
key
• Press the Central Door unlock button
on armrest trim of driver’s door
The fuel filler door will lock when Driver’s
door is locked.
To lock fuel filler door:
ONX4E050033
• Press the lock button on your smart key
1.
Turn the engine off.
• Press the Central Door lock button on
2.
Ensure Driver’s door is unlocked.
armrest trim of driver’s door
3.
Press the rear center edge of the fuel
ÃÃ
All doors will automatically lock after
filler door.
the vehicle speed exceeds 9 mph. Fuel
filler door is also locked when vehicle
speed exceeds 9 mph.
Information
If the fuel filler door does not open
because ice has formed around it, tap
lightly or push on the door to break the
ice and release the door. Do not pry on the
door. If necessary, spray around the door
with an approved deicer fluid (do not use
radiator antifreeze) or move the vehicle to
ONX4050083N
a warm place and allow the ice to melt.
4.
Pull the fuel filler door (1) outward to
access the fuel tank cap.
5.
To remove the fuel tank cap (2), turn
it counterclockwise. You may hear a
hissing noise as the pressure inside
the tank equalizes.
6. Place the cap on the fuel filler door.
5-76
05
Closing the fuel filler door
•
Do not get back into a vehicle
once you have begun refueling.
1. To install the fuel tank cap, turn it
You can generate a buildup of
clockwise until it “clicks” one time.
static electricity by touching,
2. Close the fuel filler door until it is
rubbing or sliding against any item
latched securely.
or fabric capable of producing
static electricity. Static electricity
discharge can ignite fuel vapors
Information
causing a fire. If you must re-enter
To lock the fuel filler door, make sure the
the vehicle, you should once again
fuel filler door is completely closed. Press
eliminate potentially dangerous
the LOCK button on the remote key or
static electricity discharge by
smart key to lock your vehicle. The fuel
touching a metal part of the vehicle,
filler door will also lock.
away from the fuel filler neck, nozzle
Note that if the fuel filler door is not
or other fuel source, with your bare
completely closed when the vehicle is
hand.
locked, the fuel filler door will not be
•
When using an approved portable
locked.
fuel container, be sure to place the
container on the ground prior to
refueling. Static electricity discharge
CAUTION
from the container can ignite fuel
Make sure the fuel filler door is
vapors causing a fire.
completely closed before driving
Once refueling has begun, contact
through a car wash or operating a high
between your bare hand and the
pressure spray washer.
vehicle should be maintained until
the filling is complete.
WARNING
•
Use only approved portable plastic
fuel containers designed to carry and
Automotive fuel is highly flammable
store fuel.
and explosive. Failure to follow these
•
When refueling, always shift the
guidelines may result in SERIOUS
INJURY or DEATH:
gear to the P (Park) position, set
the parking brake, and press the
• Read and follow all warnings posted
Engine Start/Stop button to the
at the gas station.
OFF position. Sparks produced by
• Before refueling, note the location
electrical components related to the
of the Emergency Fuel Shut-Off, if
engine can ignite fuel vapors causing
available, at the gas station.
a fire.
• Before touching the fuel nozzle, you
•
Do not use matches or a lighter and
should eliminate the potential build-
do not smoke or leave a lit cigarette
up of static electricity by touching
in your vehicle while at a gas station,
a metal part of the vehicle, a safe
especially during refueling.
distance away from the fuel filler
neck, nozzle, or other gas source,
with your bare hand.
• Do not use mobile phones while
refueling. Electric current and/or
electronic interference from cellular
phones can potentially ignite fuel
vapors and cause a fire.
5-77
Convenient features
• Do not over-fill or top-off your
vehicle tank, which can cause fuel
spillage.
• If a fire breaks out during refueling,
leave the vicinity of the vehicle, and
immediately contact the manager
of the gas station and then contact
the local fire department. Follow any
safety instructions they provide.
• If pressurized fuel sprays out, it can
cover your clothes or skin and thus
subject you to the risk of fire and
burns. Always remove the fuel cap
carefully and slowly. If the cap is
venting fuel or if you hear a hissing
sound, wait until the condition stops
before completely removing the cap.
• Always check that the fuel cap is
installed securely to prevent fuel
spillage in the event of an accident.
Information
Make sure to refuel your vehicle according
to the “Fuel Requirements” section in
suggested in chapter 1.
NOTICE
• Do not spill fuel on the exterior
surfaces of the vehicle. Any type of
fuel spilled on painted surfaces may
damage the paint.
• If the fuel filler cap requires
replacement, we recommend that
you use only a genuine HYUNDAI cap
or the equivalent specified for your
vehicle. An incorrect fuel filler cap
can result in a serious malfunction of
the fuel system or emission control
system.
5-78
05
LIGHTING
Exterior lights
Lighting control
To operate the lights, turn the knob at
the end of the control lever to one of the
following positions:
ODN8059201
AUTO headlamp position
The position lamp and headlamp will
be turned ON or OFF automatically
depending on the amount of daylight as
measured by the ambient light sensor (1)
ODN8059200
at the upper end of the windshield glass.
1. OFF position
Even with the AUTO headlamp feature
2. AUTO headlamp position
in operation, it is recommended to
3. Position lamp position
manually turn ON the headlamps when
4. Headlamp position
driving at night or in a fog, driving in the
rain, or when you enter dark areas, such
as tunnels and parking facilities.
Daytime Running Light (DRL)
The Daytime Running Lights (DRL) can
make it easier for others to see the front
NOTICE
of your vehicle during the day, especially
• Do not cover or spill anything on the
after dawn and before sunset. The
sensor (1) located at the upper end of
Daytime Running Lights (DRL) should
the windshield glass.
be illuminated whenever you are driving
• Do not clean the sensor using
during daylight hours. The DRL system
a window cleaner, the cleanser
will be ON when the headlamp stalk is
may leave a light film which could
in the OFF or the AUTO Position (when
interfere with sensor operation.
daylight is detected) and the Electronic
Parking Brake (EPB) is released.
• If your vehicle has window tint or
other types of metallic coating on
the front windshield, the AUTO
The DRL system will turn off when:
headlamp system may not work
• The headlamps are ON.
properly.
• The parking brake is applied.
• The vehicle is turned off.
• Parking Brake is applied
5-79
Convenient features
High beam operation
ODN8059202
Position lamp position (
)
ODN8059205
The position lamp, license plate lamp
To turn on the high beam headlamp,
and instrument panel lamp are turned
push the lever away from you. The lever
ON.
will return to its original position.
The high beam indicator will light when
the headlamp high beams are switched
on.
To turn off the high beam headlamp, pull
the lever towards you. The low beams
will turn on.
WARNING
Do not use high beam when there are
other vehicles approaching you. Using
ODN8059203
high beam could obstruct the other
driver’s vision.
Headlamp position (
)
The headlamp, position lamp, license
plate lamp and instrument panel lamp
are turned ON.
Information
The ignition switch must be in the ON
position to turn on the headlamp.
ODN8059204
To flash the high beam headlamp, pull
the lever towards you, then release the
lever. The high beams will remain ON as
long as you hold the lever towards you.
5-80
05
Turn signals and lane change signals
Battery saver function
The purpose of this feature is to prevent
the battery from being discharged.
The system automatically turns off the
position lamp when the driver turns the
vehicle off and opens the driver-side
door.
With this feature, the position lamps will
turn off automatically if the driver parks
on the side of road at night.
If necessary, to keep the lamps on when
the vehicle is turned off, perform the
ODN8059207
following:
To signal a turn, push down on the lever
(1) Open the driver-side door.
for a left turn or up for a right turn in
(2) Turn the position lamps OFF and ON
position (A).
again using the headlamp switch on
If an indicator stays on and does not flash
the steering column.
or if it flashes abnormally, one of the turn
signal bulbs may be burned out and will
require replacement.
One touch turn signal
To use One Touch Turn Signal push the
turn signal lever up or down to position
(B) and then release it.
The lane change signals will blink 3, 5 or
7 times.
You can enable the One Touch Turn
Signal function or choose the number
of blinking by selecting ‘Setup → User
Settings → Lights → One Touch Turn Signal
→ Off/3 flashes/5 flashes/7 flashes’ in the
instrument panel LCD cluster.
5-81
Convenient features
Headlamp delay function
If you place the ignition switch to the
ACC position or the OFF position with
the headlamps ON, the headlamps (and/
or position lamps) remain on for about
5 minutes. However, if the driver’s door
is opened and closed, the headlamps
are turned off after 15 seconds. Also,
with the vehicle off if the driver’s door is
opened and closed, the headlamps (and/
or position lamps) are turned off after 15
seconds.
The headlamps (and/or position lamps)
can be turned off by pressing the lock
button on the remote key or smart key
twice or turning the headlamp switch to
the OFF or AUTO position.
You can enable the headlamp delay
function by selecting ‘Setup → User
Settings → Lights → Headlight Delay.
NOTICE
If the driver exits the vehicle through
another door besides the driver
door, the battery saver function
does not operate and the headlamp
delay function does not turn OFF
automatically.
This may cause the battery to
discharge. To avoid battery discharge,
turn OFF the headlamps manually from
the headlamp switch before exiting the
vehicle.
5-82
05
HIGH BEAM ASSIST (HBA)
NOTICE
Always keep the front view camera in
good condition to maintain optimal
performance of High Beam Assist.
For more details on the precautions
of the front view camera, refer to
“Forward Collision-Avoidance Assist
(FCA)” section in chapter 7.
System settings
ODN8059206
With the engine on, select ‘Lights → High
High Beam Assist will automatically
Beam Assist (or HBA (High Beam Assist))’
adjust the headlamp range (switches
from the Settings menu to turn on High
between high beam and low beam)
Beam Assist and deselect to turn off the
depending on the brightness of detected
system.
vehicles and certain road conditions.
WARNING
Detecting sensor (Front view
camera)
For your safety, change the Settings
after parking the vehicle at a safe
location.
ONX4070075
[1] : Front view camera
The front view camera is used as a
detecting sensor to detect ambient light
and brightness while driving.
Refer to the picture above for the
detailed location of the detecting sensor.
5-83
Convenient features
System operation
• When High Beam Assist is operating,
high beam switches to low beam if
Display and control
any of the following conditions occur:
•
After selecting ‘High Beam Assist’
--
When the headlamp of an
in the Settings menu, High Beam
oncoming vehicle is detected.
Assist will operate by following the
procedure below.
--
When the tail lamp of a vehicle in
front is detected.
--
Place the headlamp switch in
the AUTO position and push
--
When the headlamp or tail lamp of a
the headlamp lever towards the
motorcycle or a bicycle is detected.
instrument cluster. The High Beam
--
When the surrounding ambient light
Assist (
) indicator light will
is bright enough that high beams
illuminate on the cluster and the
are not required.
system will be enabled.
--
When streetlights or other lights are
--
When the system is enabled, high
detected.
beam will turn on when vehicle
speed is above 25mph (40km/h).
System malfunction and
When vehicle speed is below 15mph
limitations
(25km/h), high beam will not turn
System malfunction
on.
--
The High Beam (
) indicator light
Type A
Type B
will illuminate on the cluster when
high beam is on.
•
When High Beam Assist is operating, if
the headlamp lever or switch is used,
the system operates as follow:
--
If the headlamp lever is pulled
towards you when the high beam
is off, the high beam will turn on
without High Beam Assist canceled.
When you let go of the headlamp
OTM050218N
OTM050218L
lever, the lever will move to the
When High Beam Assist is not working
middle and the high beam will turn
properly, the ‘Check High Beam Assist
off.
(HBA) system’ or ‘Check HBA (High
--
If the headlamp lever is pulled
Beam Assist system’ warning message
towards you when the high beam is
will appear and warning light will
on by High Beam Assist, low beam
illuminate on the cluster. We recommend
will be on and the system will turn
that the system be inspected by an
off.
authorized HYUNDAI dealer.
--
If the headlamp switch is placed
from AUTO to another position
(headlamp/position/off), High
Beam Assist will turn off and the
corresponding lamp will turn on.
5-84
05
Limitations of the system
WARNING
High Beam Assist may not work properly
•
At times, High Beam Assist may not
in the following situations:
work properly. It is the responsibility
•
Light from a vehicle is not detected
of the driver for safe driving
because of lamp damage, or because
practices and always check the road
it is hidden from sight, etc.
conditions for your safety.
•
Headlamp of a vehicle is covered with
•
When High Beam Assist does
dust, snow or water.
not operate normally, change
•
A vehicle’s headlamps are off but the
the headlamp position manually
fog lamps are on and etc.
between high beam and low beam.
•
There is a lamp that has a similar
shape as a vehicle’s lamp.
•
Headlamps have been damaged or
not repaired properly.
•
Headlamps are not aimed properly.
•
Driving on a narrow curved road,
rough road, uphill or downhill.
•
Vehicle in front is partially visible on a
crossroad or curved road.
•
There is a traffic light, reflecting sign,
flashing sign or mirror ahead.
•
There is a temporary reflector or flash
ahead (construction area).
•
The road conditions are bad such as
being wet, iced or covered with snow.
•
A vehicle suddenly appears from a
curve.
•
The vehicle is tilted from a flat tire or
is being towed.
•
Light from a vehicle is not detected
because of exhaust fume, smoke, fog,
snow, etc.
For more details on the limitations
of the front view camera, refer to
“Forward Collision-Avoidance Assist
(FCA)” section in chapter 7.
5-85
Convenient features
INTERIOR LIGHTS
Front lamps
WARNING
Do not use the interior lights when
driving in the dark. The interior lights
may obscure your view and cause an
accident.
NOTICE
Do not use the interior lights for
extended periods when the vehicle is
turned off or the battery will discharge.
Interior Lamp AUTO OFF
ONX4E050147
The interior lamps will automatically go
1. Front map lamp (
):
off approximately 10 minutes after the
Touch either icons to turn the map lamp
vehicle is turned off and the doors are
on or off. This light produces a spot
closed. If a door is opened, the lamp
beam for convenient use as a map lamp
will go off 40 minutes after the vehicle
at night or as a personal lamp for the
is turned off. If the doors are locked by
driver and the front passenger.
the smart key and the vehicle enters the
armed stage of the theft alarm system,
the lamps will go off five seconds later.
2. Door lamp (
):
The front or rear room lamps come on
when the front or rear doors are opened.
When doors are unlocked by the smart
key, the front and rear lamps come on
for approximately 30 seconds as long as
any door is not opened. The front and
rear room lamps go out gradually after
approximately 30 seconds when the
door is closed. However, if the Engine
Start/Stop button is in the ON position
or all doors are locked, the front and rear
lamps will turn off. If a door is opened
with the ignition switch in the ACC
position or the OFF position, the front
and rear lamps will stay on for about 20
minutes.
3. Room lamp (
)
Press the button to turn ON the room
lamp for the front/rear seats.
5-86
05
Rear lamps (if equipped)
Vanity mirror lamp
Type A
ODN8059211
OTM050200
Type B
Push the switch to turn the light on or off.
•
: The lamp will turn on if this
button is pressed.
•
: The lamp will turn off if this
button is pressed.
Glove box lamp (if equipped)
OLFP048099
Rear room lamp switch :
Press this button to turn the room lamp
on and off.
ONX4050039
The glove box lamp turns on when the
glove box is opened.
5-87
Convenient features
Luggage compartment lamp
Welcome system (if equipped)
ONX4E050073
ONX4E050038
The luggage compartment lamp is on
Welcome system helps keep the driver
when the liftgate is opened.
visible by turning on vehicle lights when
the driver approaches the vehicle.
The luggage compartment lamp is off
when the liftgate is closed.
5-88
05
Puddle Lamp or Door Handle Lamp
Headlamp and position lamp
(if equipped)
When the headlamp (lamp switch in the
When all the doors (and liftgate) are
headlamp or AUTO position) is on and
closed and locked, the puddle lamp
all doors (and liftgate) are locked and
and door handle lamp will turn on for
closed, the position lamp and headlamp
approximately 15 seconds if any of the
will come on for 15 seconds when the
below is performed.
door unlock button is pressed on the
remote key or smart key.
1. If ‘Convenience → Welcome mirror/
light → On door unlock’ is selected in
At this time, if you press the door lock
the User Settings mode on the LCD
or unlock button, the position lamp and
display,
headlamp will turn off immediately.
• the lamps will turn on when the
door lock button is pressed on the
Interior lamp
smart key.
When the interior lamp switch is in the
• the lamps will turn on when the
position and all doors (and liftgate)
are closed and locked, the room lamp
button of the outside door handle
is pressed with the smart key in
will come on for 30 seconds if any of the
below is performed.
possession.
--
When the door unlock button is
2. If both ‘Convenience → Welcome
mirror/light → On door unlock’ and
pressed on the remote key or smart
key.
‘Convenience → Welcome mirror/light
→ On driver approach’ is selected in
--
When you put your hand in the
the User Settings mode on the LCD
outside door handle while carrying the
display, the lamps will turn on when
smart key.
the vehicle is approached with the
smart key in possession.
At this time, if you press the door lock
or unlock button on the smart key the
You can activate or deactivate Welcome
lamps will turn off immediately.
Light function from the User Settings
mode on the LCD display.
5-89
Convenient features
WIPERS AND WASHERS
Front windshield wiper/washer
Windshield wipers
Operates as follows when the ignition
switch is turned ON.
MIST :
For a single wiping cycle,
move the lever down (V)
or up (MIST) and release
it. The wipers will operate
continuously if the lever is
held in this position.
OFF :
Wipers are not in operation.
ONX4050042
INT :
Wipers operate intermittently
Rear windshield wiper/washer
at the same wiping intervals.
Use this mode in light rain
or mist. To vary the speed
setting, turn the speed
control knob.
LO :
The wiper runs at a lower speed.
HI :
The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
ONX4050043
or ice on the windshield, defrost the
A. Wiper speed control (front)
windshield for about 10 minutes, or until
• MIST - Single wipe
the snow and/or ice is removed before
using the windshield wipers to ensure
• OFF - Off
proper operation.
• INT - Intermittent wipe
If you do not remove the snow and/or ice
AUTO* - Auto control wipe
before using the wiper and washer, it may
• LO- Low wiper speed
damage the wiper and washer system.
• HI - High wiper speed
B. Intermittent control wipe time
adjustment
C. Wash with brief wipes (front)
D. Rear wiper control*
• HI - High wiper speed
• LO- Low wiper speed
• OFF - Off
* : if equipped
5-90
05
AUTO Wiper Control (if equipped)
WARNING
To avoid personal injury from the
windshield wipers, when the engine
is running and the windshield wiper
switch is placed in the AUTO mode:
• Do not touch the upper end of the
windshield glass facing the rain
sensor.
• Do not wipe the upper end of the
windshield glass with a damp or wet
cloth.
ONX4EH050002
• Do not put pressure on the
The rain sensor located on the upper
windshield glass.
end of the windshield glass senses
the amount of rainfall and controls the
NOTICE
wiping cycle for the proper interval.
• When washing the vehicle, set the
The wiper operation time will be
wiper switch in the OFF (O) position
automatically controlled depends on
to stop the auto wiper operation. The
rainfall.
wiper may operate and be damaged
When the rain stops, the wiper stops.
if the switch is set in the AUTO mode
To vary the sensitivity setting, turn the
while washing the vehicle.
sensitivity control knob.
• Do not remove the sensor cover
If the wiper switch is set in AUTO mode
located on the upper end of the
passenger side windshield glass.
when the Engine Start/Stop button is in
the ON position, the wiper will operate
Damage to system components
could occur and may not be covered
once to perform a self-check of the
system. Set the wiper to the OFF (O)
by your vehicle warranty.
position when the wiper is not in use.
• Because of using a photo sensor,
temporary malfunction could occur
according to sudden ambient light
change made by stone and dust
while driving.
5-91
Convenient features
Front windshield washers
WARNING
When the outside temperature is below
freezing, ALWAYS warm the windshield
using the defroster to help prevent
the washer fluid from freezing on the
windshield and obscuring your vision
which could result in an accident and
serious injury or death.
NOTICE
• To prevent possible damage to the
ONX4E050044
washer pump, do not operate the
washer when the fluid reservoir is
In the OFF position, pull the lever gently
empty.
toward you to spray washer fluid on the
windshield and to run the wipers 1-3
• To prevent possible damage to the
cycles. The spray and wiper operation
wipers or windshield, do not operate
will continue until you release the lever. If
the wipers when the windshield is
the washer does not work, you may need
dry.
to add washer fluid to the washer fluid
• To prevent damage to the wiper
reservoir.
arms and other components, do
not attempt to move the wipers
manually.
• To prevent possible damage to the
wipers and washer system, use anti-
freezing washer fluids in the winter
season or cold weather.
5-92
05
Rear window wiper and washer
ONX4050043N
The rear window wiper and washer
switch is located at the end of the wiper
and washer switch lever. Turn the switch
to the desired position to operate the
rear wiper and washer.
HI - High wiper speed
LO - Low wiper speed
OFF - Off
ONX4050045N
Push the lever away from you to spray
rear washer fluid and to run the rear
wipers 1~3 cycles. The spray and wiper
operation will continue until you release
the lever.
5-93
Convenient features
MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)
ONX4050100N
1. Fan speed control knob
5. A/C (air conditioning) button
2. Temperature control knob
6. Air intake control button
3. Front windshield defroster button
7. Mode selection button
4. Rear window defroster button
5-94
05
Heating and air conditioning
3. Set the temperature control to the
desired position.
1. Start the engine.
4. Set the air intake control to the
2. Set the mode to the desired position.
outside (fresh) air position.
To improve the effectiveness of
5. Set the fan speed control to the
heating and cooling, select:
desired speed.
--
Heating:
6. If air conditioning is desired, turn the
--
Cooling:
air conditioning system on.
Mode selection
The actual shape of air conditioner may differ from the illustration.
ONX4050102
The mode selection button controls the direction of the air flow through the ventilation
system.
5-95
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст