Hyundai Tiburon (2003 year). Manual — part 163

[HINT]
Codes other than these may be output at this time, but they are not relevant to this procedure.

C. Turn the ignition switch to LOCK, and wait for 30 seconds.

D. Turn the ignition switch to ON, and wait for 30 seconds.

E. Using the Hi-Scan Pro, check for DTCs.

There is no DTC.

9. Check the PAB squib.

[PREPARATION]

[CHECK]

[HINT]
Codes other than these may be output at this time, but they are not relevant to this procedure.

A. Turn the ignition switch to LOCK.

B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds.

C. Connect the PAB connector.

D. Connect the negative (-) terminal cable from the battery, and wait for 30 seconds.

A. Turn the ignition switch to ON, and wait for at least 30 seconds.

B. Clear the malfunction code stored in the memory with the Hi-Scan Pro.

C. Turn the ignition switch to LOCK, and wait for 30 seconds.

D. Turn the ignition switch ON, and wait for 30 seconds.

E. Using the Hi-Sacn Pro, check for DTCs.

There is no DTC.

10. Check the SAB squib.

[PREPARATION]

A. Turn the ignition switch to LOCK.

B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds.

C. Connect the SAB connector.

D. Connect the negative (-) terminal cable from the battery, and wait for 30 seconds.

[CHECK]

[HINT]
Codes other than these may be output at this time, but they are not relevant to this procedure.

A. Turn the ignition switch to ON, and wait for at least 30 seconds.

B. Clear the malfunction code stored in the memory with the Hi-Scan Pro.

C. Turn the ignition switch to LOCK, and wait for 30 seconds.

D. Turn the ignition switch ON, and wait for 30 seconds.

E. Using the Hi-Sacn Pro, check for DTCs.

There is no DTC.

11. Check the BPTs squib.

[PREPARATION]

[CHECK]

[HINT]
Codes other than these may be output at this time, but they are not relevant to this procedure.

A. Turn the ignition swich to LOCK.

B. Disconnect the negative (-) terminal cable from the battery, and wait for 30 seconds.

C. Connect the BPTs connector.

D. Connect the negative (-) terminal cable from the battery, and wait for 30 seconds.

A. Turn the ignition switch to ON, and wait for 30 seconds.

B. Clear the malfunction code stored in the memory with the Hi-Scan Pro.

C. Turn the ignition switch to LOCK, and wait for 30 seconds.

D. Turn the ignition switch to ON, and wait for 30 seconds.

E. Using the Hi-Scan Pro, check for DTCs.

There is no DTC.

12. Check the Satellite sensors.

[PREPARATION]

[CHECK]

[HINT]
Codes other than these may be output at this time, but they are not relevant to this procedure.

A. Turn ignition switch to LOCK.

B. Disconnect the negative (-) terminal cable from the battery, and wait at least 30 seconds.

C. Connect the Satellite sensor connector.

D. Connect the negative (-) terminal cable from the battery, and wait at least 30 seconds.

A. Turn the ignition switch to ON, and wait at least 30 seconds.

B. Clear the malfunction code stored in memory with Hi-scan.

C. Turn the ignition switch to LOCK, and wait at least 30 seconds.

D. Turn the ignition switch to ON, and wait at least 30 seconds.

E. Using the Hi-Scan Pro, check for DTCs.

There is no DTC.

13. Check the Clock spring.

[PREPARAION]

[CHECK]
Turn the ignition switch ON, and measure the voltage between the DAB high side and the body ground.
Voltage : 0V

A. Turn the ignition switch to LOCK.

B. Disconnect the connector between the SRSCM and the clock spring.

CIRCUIT INSPECTION

DTC

B1346
B1347

DAB resistance too high (R

≥

6.70

Ω

)

DAB resistance too low (R

≤

1.06

Ω

)

CIRCUIT DESCRIPTION

DTC Detecting Condition

Trouble Area

• Too high or low resistance between DAB high (+) wiring

harness and DAB low (-) wiring harness of squib.

• DAB squib

• DAB malfunction

• Clock spring malfunction

• SRSCM malfunction

• Clock spring

• SRSCM

• Wire harness

WIRING DIAGRAM

INSPECTION PROCEDURE

1. Preparation

(1) Disconnect the negative (-) terminal cable from the battery, and wait at least 30 seconds.

(2) Remove the DAB module.

(3) Disconnect the connectors of the PAB, left and right side airbags, belt pretensioners and satellite sensors.

(4) Disconnect the SRSCM connector.