Hyundai Tiburon (2003 year). Manual — part 64
D. If the steering continues to pull to the opposite side, replace the front wheels with new ones.
WHEEL RUNOUT
1. Jack up the vehicle and support it with jack stands.
2. Measure the wheel runout with a dial indicator as illustrated.
3. Replace the wheel if the wheel runout exceeds the limit.
LH : Left Hand side, RH : Right Hand side
Wheel runout [Limit]
Steel wheeel
Radial 0.6mm (0.028 in.) : (Average of LH & RH)
Axial 1.0mm (0.039 in.)
Aluminum wheel
Radial 0.3mm (0.012 in.)
Axial 0.3mm (0.012 in.)
TIGHTENING WHEEL NUT
1. Tightening torque
Steel and aluminum alloy wheel
Specified torque
90~110 Nm (900~1,100 kgf·cm, 65~80 lbf·ft)
Rotate the tires in the pattern illustrated.
When using an impact gun, final tightening torque should be checked using a torque wrench.
2. Tightening order
Check the torque again after tightening the wheel nuts diagonally.
WHEEL ROTATION
When rotating the 215/45 ZR17 tires, ensure to follow the "ROTATION"direction marked on the sidewall of
tires.
When rotating the tires of the left and right, seperate the wheel from the tire and then re-assemble them.
CHECKING FOR PULL AND WANDER
1. If the steering pulls to one side, rotate the tires according to the following wheel rotation procedure.
A. Rotate the front right and front left tires, and perform a road test in order to confirm vehicle stability.
B. If the steering pulls to the opposite side, rotate the front and rear tires, and perform a road test again.
C. If the steering continues to pull to one side, rotate the front right and left tires again, and perform a road
test.
D. If the steering continues to pull to the opposite side, replace the front wheels with new ones.
2. On some vehicles which dirft or pull to the right only, the following procedure may be applied for fixing.
A. Adjust tire pressure as recommended below (4 tire) prior to conducting road test.
Tire inflation pressure : 2.1 kgf/cm² (30 psi)
Front 215/45 ZR 17 tire only : 2.2 kgf/cm² (32 psi)
B. To eliminate the pulling, rotate the front tires and test drive the vehicle to see if the pulling returns.
C. If a vehicle still exhibits the pulling to the right, replace the right front strut insulator with the redesigned
new part (Part No. 54610-2C000A) which increases the caster angle. (see page SS-11)
• This procedure applies to the vehicle pulls to the right only.
• Confirm the direction of the vehicle pulling by road testing prior to performing the repair procedure.
• If 'Michelin' tires are installed, do not rotate the tires because they are directional. Replace the
right front strut insulator only.
TIBURON(GK) > 2003 > G 2.7 V6 DOHC > Driveshaft and axle > General Information > Special Service
Tools, TIBURON(GK) > 2003 > G 2.7 V6 DOHC > Driveshaft and axle > General Information > Special
Service Tools
SPECIAL TOOLS
Tool (Number and Name)
Illustration
Use
09216-21100
Mounting bushing remover and
installer
Removal of the center bearing (Use with
09495-33100)
09495-33000
Puller
Removal of wheel bearing inner race from
the hub.
09495-33100
Center bearing remover and
installer
1. Removal of wheel bearing from the
knuckle. (Use with 09517-29000)
2. Installation of hub to the knuckle.
3. Removal of the center bearing (Use with
09216-21100)
09517-21500
Front hub remover and installer
1. Removal of front hub from the knuckle.
(Use with 09517-29000)
2. Measurement of front wheel bearing
pre-load. (Use with 09532-11600)
09517-29000
Knuckle arm bridge
1. Removal of wheel bearing outer race
from the knuckle. (Use with 09495-
33100)
09517-43001
Bearing puller
Removal of the center bearing bracket
09532-11600
Preload socket
Measurement of front wheel bearing pre-
load. (Use with 09517-21500)
09532-11500
Pinion bearing outer race
Installation of wheel bearing to the knuckle.
09568-34000
Ball joint puller
Separation of front lower arm and tie rod
end ball joint.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст