Chrysler PT Cruiser. Manual — part 910
(3) When installing hood, align all marks and
secure bolts. The hood should be aligned to 4 mm
(0.160 in.) gap to the front fenders and flush across
the top surfaces along fenders.
(4) Verify hood operation and alignment.
HOOD LATCH
REMOVAL
(1) Release hood latch and open hood.
(2) Support hood on prop rod.
(3) Remove grille.
(4) Remove screws attaching hood latch to radiator
closure panel (Fig. 3).
(5) Remove hood latch from closure panel.
(6) Disengage remote release cable from latch (Fig.
4).
INSTALLATION
(1) Engage remote release cable into latch (Fig. 4).
(2) Place hood latch onto radiator closure panel
(Fig. 3).
(3) Install bolts attaching latch to closure panel.
(4) Install grille.
(5) Close hood and verify alignment of hood and
that latch is securely engaged.
Fig. 2 HOOD
1 - HOOD
2 - HOOD HINGE
3 - FRONT FENDER
Fig. 3 HOOD LATCH
1 - HOOD ADJUSTER BUMPER
2 - HOOD LATCH
Fig. 4 HOOD LATCH RELEASE CABLE
1 - HOOD LATCH RELEASE CABLE
2 - HOOD LATCH
23 - 98
HOOD
PT
HOOD (Continued)
HOOD LATCH RELEASE CABLE
REMOVAL
(1) Remove hood latch.
(2) Disconnect remote hood release cable from
hood latch (Fig. 4).
(3) Remove left front cowl trim panel.
(4) Remove screws attaching hood release handle
to cowl panel.
(5) Disconnect rubber grommet from dash panel
behind instrument panel.
(6) Pull release cable through hole in dash panel.
(7) Remove cable and handle from vehicle.
INSTALLATION
(1) Assemble cable and handle onto vehicle.
(2) Push release cable through hole in dash panel.
(3) Connect rubber grommet into dash panel.
(4) Install screws attaching hood release handle to
cowl panel.
(5) Install left front cowl trim panel.
(6) Connect remote hood release cable to hood
latch (Fig. 4).
(7) Install hood latch.
(8) Close hood and verify operation.
HOOD LATCH STRIKER
REMOVAL
(1) Release hood latch and open hood.
(2) Remove bolts attaching striker to inside of
hood (Fig. 5).
(3) Remove hood latch striker from vehicle.
INSTALLATION
(1) Position hood latch striker on vehicle (Fig. 5).
(2) Install bolts attaching hood latch striker to
hood.
(3) Align hood latch striker to engage smoothly
into hood latch.
(4) Verify hood operation and alignment. Adjust as
necessary.
(5) Tighten attaching bolts to 13.5 N·m (10 ft. lbs.)
torque.
SILENCER PAD
REMOVAL
(1) Open hood.
(2) Remove fasteners attaching hood silencer to
hood (Fig. 6).
(3) Remove hood silencer from vehicle.
INSTALLATION
(1) Place hood silencer in position on hood (Fig. 6).
(2) Install fastener attaching hood silencer to hood.
(3) Close hood.
Fig. 5 HOOD STRIKER
1 - HOOD STRIKER
2 - HOOD
Fig. 6 HOOD SILENCER
1 - HOOD
2 - HOOD INNER PANEL SILENCER
PT
HOOD
23 - 99
INSTRUMENT PANEL
TABLE OF CONTENTS
page
page
ACCESSORY SWITCH BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
. . . . . . . . . . . . . . . . . . . . . . . . 100
CLUSTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
. . . . . . . . . . . . . . . . . . . . . . . . 102
GLOVE BOX
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
. . . . . . . . . . . . . . . . . . . . . . . . 103
GLOVE BOX LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
. . . . . . . . . . . . . . . . . . . . . . . . 103
GLOVE BOX LOCK CYLINDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
. . . . . . . . . . . . . . . . . . . . . . . . 104
INSTRUMENT PANEL ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
. . . . . . . . . . . . . . . . . . . . . . . . 109
INSTRUMENT PANEL CENTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
. . . . . . . . . . . . . . . . . . . . . . . . 112
INSTRUMENT PANEL CENTER BEZEL
CONTROL KNOBS
REMOVAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
. . . . . . . . . . . . . . . . . . . . . . . . 112
INSTRUMENT PANEL END CAP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
. . . . . . . . . . . . . . . . . . . . . . . . 113
INSTRUMENT PANEL TOP COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
. . . . . . . . . . . . . . . . . . . . . . . . 113
STEERING COLUMN OPENING COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
. . . . . . . . . . . . . . . . . . . . . . . . 115
ACCESSORY SWITCH BEZEL
REMOVAL
NOTE: The accessory switches are serviced sepa-
rately, but the cigar lighter/power outlet is not (Fig.
1).
(1) Open hood.
(2) Disconnect and isolate the battery negative
cable (Fig. 2).
(3) Remove the instrument panel center bezel.
Refer to Removal and Installation, Instrument Panel
Center Bezel in this section.
(4) Remove two screws retaining the accessory
switch bezel (Fig. 3).
(5) Disconnect the harness connectors to the fol-
lowing (Fig. 4):
• Rear Window Defogger Switch (if equipped)
• Traction Control Switch (if equipped)
• Cigar Lighter/Power Outlet
• Rear Windshield Washer/Wiper Switch
(6) To remove switches from bezel, use both
thumbs and slightly pull out on the two walls that
are holding the switches (Fig. 5).
INSTALLATION
NOTE: The accessory switches are serviced sepa-
rately, but the cigar lighter/power outlet is not.
If replacing the accessory switch bezel, you must
transfer the switches to the new bezel.
(1) Reconnect accessory switch bezel connectors
(Fig. 4).
(2) Reinstall switch bezel into instrument panel
opening and install two retaining screws (Fig. 3).
(3) Reinstall instrument panel center bezel. Refer
to Removal and Installation, Instrument Panel Cen-
ter Bezel in this section.
(4) Reconnect the battery negative cable (Fig. 2).
(5) Close the hood.
(6) Verify vehicle and system operation.
23 - 100
INSTRUMENT PANEL
PT
Fig. 1 ACCESSORY SWITCH BEZEL LOCATION
1 - ACCESSORY SWITCH BEZEL
Fig. 2 DISCONNECT AND ISOLATE BATTERY
NEGATIVE CABLE
Fig. 3 ACCESSORY SWITCH BEZEL
Fig. 4 ACCESSORY SWITCH BEZEL CONNECTORS
Fig. 5 ACCESSORY SWITCH BEZEL SWITCH
PT
INSTRUMENT PANEL
23 - 101
ACCESSORY SWITCH BEZEL (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст