Chrysler PT Cruiser. Manual — part 912
Fig. 15 INSTRUMENT PANEL ASSEMBLY
23 - 106
INSTRUMENT PANEL
PT
INSTRUMENT PANEL ASSEMBLY (Continued)
(15) Remove the two left side A-pillar, instrument
panel retaining bolts and one nut. (Fig. 17)
(16) Remove two retaining bolts at the left side of
the center support bracket (Fig. 18).
(17) Remove four screws to center console.
(18) Using a trim stick or equivalent, gently pry
rear power window switch out of console and discon-
nect wiring and remove.
(19) Pull parking brake handle all the way up.
(20) Lift up the front of the center console to gain
access to the power outlet connector.
(21) Disconnect one wire connector to console
mounted auxiliary power outlet.
(22) Pull up on rear of console first to clear park-
ing brake handle and remove from vehicle.
(23) If equipped with an automatic, remove the
shifter handle and shifter bezel.
(a) Shifter Handle - Loosen the set screw
retaining the shifter handle and pull up on handle
to remove.
(b) Shifter Bezel - Pull upward on edge of
shifter bezel, disconnect the illumination lamp and
remove bezel.
(24) Disconnect and remove the two remaining
center console wiring connectors:
(a) Occupant Restraint Controller (ORC) connec-
tor
(b) Park Brake Switch connector
(25) Remove two retaining bolts at the right side
of the center support bracket (Fig. 18).
NOTE: The center console wiring is routed under-
neath the rear floor heat duct. Loosen the retainers
holding down the heat duct and you can maneuver
the wiring from underneath it without removal.
(26) Remove glove box assembly:
(a) Open glove box and push in on the sides of
the glove box bin to allow the retainers to clear the
instrument panel.
(b) Let the glove box drop down and give it
quick pull downward to disengage the hinge.
(27) Remove two screws to the right instrument
panel end cap.
(28) Pull end cap rearward to unsnap and remove
from vehicle.
1 - INSTRUMENT PANEL TOP COVER
10 - INSTRUMENT PANEL STEERING COLUMN COVER
2 - INSTRUMENT PANEL
11 - HVAC CONTROL KNOBS
3 - INSTRUMENT PANEL OUTBOARD A/C OUTLET HOUSING
12 - INSTRUMENT PANEL CENTER BEZEL
4 - PASSENGER AIRBAG COVER, PASSENGER AIRBAG MODULE
13 - STEERING COLUMN SHROUD
5 - INSTRUMENT PANEL END CAP
14 - FUSE COVER
6 - INSTRUMENT PANEL GLOVE BOX
15 - INSTRUMENT PANEL END CAP
7 - INSTRUMENT PANEL GLOVE BOX DOOR
16 - INSTRUMENT CLUSTER BEZEL
8 - INSTRUMENT PANEL GLOVE BOX LATCH
17 - INSTRUMENT PANEL CLUSTER BEZEL A/C OUTLET
HOUSING
9 - LOCK CYLINDER
18 - CLUSTER SUPPORT PANEL
Fig. 16 BRAKE PEDAL SUPPORT BRACKET,
INSTRUMENT PANEL RETAINING BOLTS
1 - INSTRUMENT PANEL
2 - FLOOR PAN BRACKET
3 - ATTACHING SCREW(S)
PT
INSTRUMENT PANEL
23 - 107
INSTRUMENT PANEL ASSEMBLY (Continued)
(29) Remove the two right side A-pillar, instru-
ment panel retaining bolts and one nut (Fig. 17).
(30) Disconnect the right side instrument panel
wire connectors:
(a) Antenna
(b) Overhead Systems (Fig. 19)
(c) Blower Motor
(d) Left Door Harness
(e) Body Harness
(31) Remove the four fence line instrument panel
retaining bolts (Fig. 20).
(32) With the help of an assistant, carefully
remove the instrument panel from the vehicle being
careful not to damage the instrument panel or vehi-
cle interior.
NOTE: If the instrument panel is being replaced, all
the components left on the assembly must be
transferred.
This would include:
• Passenger Airbag
• Instrument Cluster and Cluster Bezel
• Cluster Area Support Panel
• Remote Keyless Entry Module (if equipped)
• Radio
• Accessory Switch Bezel
• Left and Right Instrument Panel Speakers
• Instrument Panel Wire Harness
• Right Instrument Panel A/C Outlet Housing
Assembly
• All A/C and Heat Duct work and Plumbing
Fig. 17 INSTRUMENT PANEL
1 - WINDSHIELD COWL
4 - INSTRUMENT PANEL TO COWL SCREW(S)
2 - INSTRUMENT PANEL TO COWL STUD RT/LT
5 - INSTRUMENT PANEL
3 - INSTRUMENT PANEL TO COWL NUT(S)
23 - 108
INSTRUMENT PANEL
PT
INSTRUMENT PANEL ASSEMBLY (Continued)
INSTALLATION
(1) With the help of an assistant, carefully install
the instrument panel in the vehicle being careful not
to damage the instrument panel or vehicle interior.
(2) Install the four fence line instrument panel
retaining bolts (Fig. 20).
(3) Connect the right side instrument panel wire
connectors:
(a) Antenna
(b) Overhead Systems (Fig. 19)
(c) Blower Motor
(d) Left Door Harness
(e) Body Harness
(4) Install the two right side A-pillar, instrument
panel retaining bolts and one nut (Fig. 17).
(5) Place the right end cap in position and snap
into place.
(6) Install two screws to the right instrument
panel end cap.
(7) Install glove box assembly:
(a) Place glove box assembly in position and
make the orientation of the hinge is correct and
snap glove box assembly hinge into place (Fig. 9).
(b) Lift glove box assembly up, push in on the
box/bin sides to allow the glove box to pass by the
instrument panel.
(c) Close glove box.
NOTE: The center console wiring is routed under-
neath the rear floor heat duct. You can maneuver
the wiring underneath the rear seat heat duct with-
out removal.
(8) Install two retaining bolts at the right side of
the center support bracket (Fig. 18).
(9) Connect the following two center console wiring
connectors:
(a) Occupant Restraint Controller (ORC) connec-
tor
(b) Park Brake Switch connector
(10) If equipped with an automatic, install the
shifter handle and shifter bezel.
(a) Shifter Bezel - Connect the illumination
lamp, place in position and snap into place.
(b) Shifter Handle - Place the shifter handle on
the shifter assembly, tighten the set screw retain-
ing the shifter handle.
Fig. 18 INSTRUMENT PANEL CENTER SUPPORT
RETAINING BOLTS
1 - ATTACHING SCREW(S)
2 - FLOOR PAN BRACKET
Fig. 19 INSTRUMENT PANEL TO OVERHEAD
SYSTEMS JUMPER HARNESS CONNECTOR -
TYPICAL LEFT OR RIGHT
1 - INSTRUMENT PANEL
2 - HEADLINER CONNECTOR
PT
INSTRUMENT PANEL
23 - 109
INSTRUMENT PANEL ASSEMBLY (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст