Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 102
Symptom:
DECKLID RELEASE SWITCH FAILURE
When Monitored and Set Condition:
DECKLID RELEASE SWITCH FAILURE
When Monitored:
Continuously.
Set Condition:
The BCM detects the decklid release switch stuck in the depressed
condition for more than 30 seconds.
POSSIBLE CAUSES
DECKLID RELEASE SWITCH SHORTED
DECKLID RELEASE SWITCH SENSE CIRCUIT SHORT TO GROUND
WIRING HARNESS INTERMITTENT DEFECT
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII, erase DTC’s.
Cycle the ignition switch from off to on and wait at least 30 seconds.
With the DRBIII, read DTC’s.
Did this DTC reset?
All
Yes
→ Go To 2
No
→ Go To 5
2
Disconnect the Decklid Release Switch harness connector.
With the DRBIII, erase DTC’s.
Cycle the ignition switch from off to on and wait at least 30 seconds.
With the DRBIII, read DTC’s.
Did this DTC reset?
All
Yes
→ Go To 3
No
→ Replace the Decklid Release Switch.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the Decklid Release Switch harness connector.
Disconnect the BCM
9C29 harness connector.
Turn the ignition on.
Measure the resistance between ground and the Decklid Release Switch Sense
circuit.
Is the resistance below 100.0 ohms?
All
Yes
→ Repair the Decklid Release Switch Sense circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
393
POWER DOOR LOCKS/RKE
TEST
ACTION
APPLICABILITY
4
If there are no possible causes remaining, view repair.
All
Repair
Replace the Body Control Module Module.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
Note: Visually inspect the related wire harness connectors. Look for broken,
bent, pushed out, or corroded terminals.
Were any problems found?
All
Yes
→ Repair wiring harness/connectors as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
394
POWER DOOR LOCKS/RKE
DECKLID RELEASE SWITCH FAILURE —
Continued
Symptom:
DOOR LOCK SWITCH FAILURE
When Monitored and Set Condition:
DOOR LOCK SWITCH FAILURE
When Monitored:
Continuously
Set Condition:
When the BCM detects a signal on the Driver or Passenger Door Lock
Switch for over 8 seconds this code will set. If the voltage is over 5.5 volts for over 8 seconds,
both door lock switches will be inoperative until the offending input is corrected. This is an
active code only.
POSSIBLE CAUSES
DRIVER DOOR LOCK SWITCH SHORTED
PASSENGER DOOR LOCK SWITCH SHORTED
DRIVER DOOR LOCK SWITCH MUX CIRCUIT SHORTED TO VOLTAGE
PASSENGER DOOR LOCK SWITCH MUX CIRCUIT SHORTED TO VOLTAGE
SYSTEM INTERMITTENT
BODY CONTROL MODULE - DOOR LOCK SWITCH SHORTED
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase DTC’s.
Operate both door lock switches to the lock and unlock positions several times.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Go To 2
No
→ Go To 7
2
Disconnect the Driver Door Lock Switch harness connector.
Turn the ignition on.
With the DRBIII, enter BODY COMPUTER then SENSORS and observe the Dr Lock
SW voltage
Is there any voltage present?
All
Yes
→ Go To 3
No
→ Replace the Driver Door Lock Switch.
Perform BODY VERIFICATION TEST - VER 1.
3
Disconnect the Passenger Door Lock Switch harness connector.
Turn the ignition on.
With the DRBIII, enter BODY COMPUTER then SENSORS and observe the Dr Lock
SW voltage
Is there any voltage present?
All
Yes
→ Go To 4
No
→ Replace the Passenger Door Lock Switch.
Perform BODY VERIFICATION TEST - VER 1.
395
POWER DOOR LOCKS/RKE
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the BCM
9C49 harness connector.
Disconnect the Driver Door Lock Switch connector.
Turn the ignition on.
Measure the voltage of the Driver Door Lock Switch Mux circuit.
Is there any voltage present?
All
Yes
→ Repair the Driver Door Lock Switch Mux circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the BCM
9C49 harness connector.
Disconnect the Passenger Door Lock Switch connector.
Turn the ignition on.
Measure the voltage of the Passenger Door Lock Switch Mux circuit.
Is there any voltage present?
All
Yes
→ Repair the Passenger Door Lock Switch Mux circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
If there are no possible causes remaining, view repair.
All
Repair
Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
7
Turn the ignition off.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Check for either switch possibly sticking
Were any problems found?
All
Yes
→ Repair or replace as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
396
POWER DOOR LOCKS/RKE
DOOR LOCK SWITCH FAILURE —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст